Safety Instructions

WARNING: Important safety instructions
to be read before installation and use.
Incorrect installation or use can lead to serious injury and
will void manufacturer's liability and warranty. It is
important for the safety of persons to follow the enclosed
instructions.
Save these instructions for future reference.
• Do not expose to water, moisture, humid and damp
environments or extreme temperatures.
• Persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and
knowledge, should not be allowed to use this product.
• Use or modication outside the scope of this instruction
manual will void warranty.
• Installation and programming to be performed by a
suitably qualied installer.
• Follow installation instructions.
• For use with motorized shading devices.
• Frequently inspect for improper operation.
Do not use if repair or adjustment is necessary.
• Keep clear when in operation.
• Replace battery with correctly specied type.
FCC ID: 2AGGZ003B9ACA3E
IC:
21769-003B9ACA3E
Operation Temperature Range: -10°C to +50°C
Ratings: 3VDC, 15mA
This product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the
battery compartment does not close securely, stop using
the product and keep it away from children.
If you think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical
attention.
WARNING: Do not ingest battery,
Chemical Burn Hazard.
Do not dispose
of in general
waste.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: Changes or modications to this unit not
expressly approved by the party responsible for
compliance could void the user's authority to operate the
equipment.
This device contains licence-exempt transmitter(s)/receiv-
er(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le
présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses
and can radiate radio frequencyenergy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
9-12 hours
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
FCC & ISED STATEMENT
Low battery alert
LED Status:
Blinking Red
USB Cable
USB Power Supply
Charging in process
Blinking Green
Battery has finished
charging
Solid Green
During operation, if the battery is
low, the Endcap LED indicator will
flash red to prompt the user to
charge the system.
PRODUCT RANGE
This Quick Start Programming Guide is for
the Top Down Bottom Up system (controller
and remote).
For battery motors ensure the motor is fully
charged as per instructions.
CHARGE 100%
Use a spare remote to individually program
each shade. Then use that remote to group
rooms as per the user’s needs. If you go back
and service the installation later then, that
same remote can be used to check the
individual shades.
INSTALLERS REMOTE
Run the fabric up and down several times to
ensure fabric has settled to some extent and
re adjust the limits if needed.
SETTLE FABRIC
If pre-programmed: before shipping the motor
ensure the motor is put into sleep mode
so it doesn’t activate during transit.
SLEEP MODE
Prevent users accidently changing the limit;
ensure the remote is locked as your last step
of programming.
LOCK REMOTE
Ask the customer the day before to think how
shades will be zoned on the remote.
This may save an extra call out.
ZONE / GROUPS
INSTALLER
BEST PRACTICE AND TIPS
P1 LOCATIONS
TALLERINS
PROGRAMMINGQUICK START
ctory reset motors only.uld be used for new installation or faThis setup wizard sho
izard from the beginning.Individual steps may not work if you haven't followed the w
ON
REMOTE
STEP 1
SECS
2
SECS
2
SECS
2
PAIRING REMOTE
WITH MOTOR
The motor will respond with Jog x1
Press the P1 button on the motor for
2 Seconds until the motor responds
STEP 2
JOG
x
2
MOTOR RESPONSE
JOG
x
1
MOTOR RESPONSE
JOG
x
2
MOTOR RESPONSE
Press ><
(Up)
or <>
(Down)
to check the
motor direction. If correct skip to step 5.
CHECK
DIRECTION
STEP 3
OR
+
+
If the shade direction needs to be reversed;
press and hold the
><
(Up)
&
<>
(Down)
buttons
together for 2 seconds until the
motor Jog x1.
The operation is only valid when there are no limits.
CHANGE
DIRECTION
STEP 4
SET
UPPER LIMIT
STEP 5
SET
BOTTOM LIMIT
STEP 6
SECS
6
Repeat steps 1-6 for all motors.
Once complete Press the lock button
for 5 seconds to lock the remote,
the L will breifly appear on the screen.
SAVE
YOUR LIMIT
STEP 7
SECS
14
To reset all settings in the motor press
and hold the P1 Button for 14 seconds,
you should see 4 independent jogs.
FACTORY RESET
MOTOR RESET PROCEDURE
SECS2 SECS6 SECS10 SECS14
MOTOR RESPONSE
Press  (lower channel) or
 (higher channel) buttons to select the
channel that needs to be programmed
Within 10 seconds hold the Left STOP
button on the remote until the motor Jogs x2:
Top Down Button Up System
P1 Button
5V USB Charging portLED
RF Controller
There are 2 different End Caps:
1. Left End Cap
2. Right End Cap
Motor 1 Connection Port
Motor 2 Connection Port
Move the middle hembar to the
desired top limit by pressing the right
><
(Up)
button repeatedly.
Then press and hold right
><
(Up)
&
right STOP buttons together for
2
seconds
to save the top limit.
Repeat this process using the left
><
(Up)
button to set desired top limit and
left
><
(Up)
& left STOP for
2 seconds
to
set the lower hembar top limit.
SECS
2
JOG
x
2
MOTOR RESPONSE
JOG
x
4
MOTOR RESPONSE
+
Move the middle hembar to the
desired bottom limit by pressing the
right
<>
(Down)
button repeatedly.
Then press and hold right
<>
(Down)
&
right STOP buttons together for
2
seconds
to save the bottom limit.
Repeat this process using the left
<>
(Down)
button to set desired bottom limit
and left
<>
(Down)
& left STOP for
2
seconds
to set the lower hembar top limit.
Switch
Charging Port
P1 Button
Note:
TDBU
Programming
Guide
Lock Button
P1
P1
OR
Middle Hembar
Lower Hembar
L
15