MOTOR PROGRAMMING INSTRUCTIONS 5V Zero & Li-ion Wire-free Motors Live Feedback SOFT STOP ELECTRONIC LIMIT SELECTABLE SPEED SOLAR OPTION LEVEL CONTROL BATTERY POWERED • Fav Position 433 MHZ BI-DIRECTIONAL USE THIS DOCUMENT WITH THE FOLLOWING MOTORS: DESCRIPTION 5V ZERO LI-ION 0.5NM MOTOR [Ø20/5V/20rpm] (Skyline) 5V [Ø20/5V/20rpm] (S45) 5V ZERO LI-ION 1.
SAFETY INSTRUCTIONS WARNING: Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty. WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
CONTENTS 1 ASSEMBLY 4 12 BATTERY CHECK FUNCTION 15 2 RETROFIT INSTALLATION 5 12.1 Send Shade to battery charge level 15 3 CHARGING 5 13 15 4 P1 BUTTON FUNCTIONS 6 4.1 Motor state test 6 4.2 Motor configuration options 6 5 7 5.1 Pair motor with controller 7 5.2 Check motor direction 7 5.3 Set limits 8 6 9 ADJUSTING LIMITS 6.1 Adjust upper limit 9 6.2 Adjust lower limit 9 7 CONTROLLERS AND CHANNELS CHARGING LED 13.
1 ASSEMBLY 4 | Automate™ Programming Instructions | 5V Li-ion Tubular Motors ROLLEASE ACMEDA
2 RETROFIT INSTALLATION 3 CHARGING ROLLEASE ACMEDA Automate™ Programming Instructions | 5V Li-ion Tubular Motors | 5
4 P1 BUTTON FUNCTIONS 4.1 Motor state test This table describes the function of a short P1 Button press/release (<2 seconds) depending on current motor configuration. P1 Press Short Press 4.2 Condition Function Achieved Visual Feedback Audible Feedback Function Described If limit is NOT set None No Action None No Action If limits are set Operational control of motor, run to limit.
5 INITIAL SET UP 5.1 Pair motor with controller Hold P1 button on motor head. Select channel on controller. IMPORTANT Hold STOP on controller. Motor Response Motor Response Consult user manual for your controller for information on selecting channel. Approx. Motor is now in step mode and ready for setting limits 5.2 Check motor direction To check travel direction of shade, press UP or DOWN on controller. . To reverse shade direction, hold both UP and DOWN. Until the motor responds.
5.3 Set Limits To save upper limit, hold UP and STOP. IMPORTANT Cycle shade up and down prior to setting limits to settle fabric Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. Motor Response OR Move shade to the desired highest or lowest position by pressing the UP or DOWN buttons on controller. Approx. 5 SEC S To save lower limit, hold DOWN and STOP. OR Motor Response Approx.
6 ADJUSTING LIMITS 6.1 Adjust upper limit Hold UP and STOP on controller. Move shade to the desired highest position by pressing the UP or DOWN button. To save upper limit, hold UP and STOP. OR Motor Response Approx. 6.2 Motor Response 5 SEC S Approx. 5 SEC S Adjust lower limit Hold DOWN and STOP on controller. Move shade to the desired lowest position by pressing the UP or DOWN button. To save lower limit, hold DOWN and STOP. OR Motor Response Approx. 5 SEC S Motor Response Approx.
7 CONTROLLERS AND CHANNELS 7.1 Using P2 Button on existing controller to add a new controller or channel A = Existing controller or channel (to keep) B = Controller or channel to add or remove Press P2 on controller A. Motor Response IMPORTANT 7.2 Press P2 on controller A. Motor Response Press STOP on an new controller to add it.
8 FAVORITE POSITIONING 8.1 Set a favorite position Move shade to the desired position by pressing the UP or DOWN button on the controller. OR Press P2 on controller. Motor Response 8.2 Press STOP on controller. Motor Response Press STOP on controller. Motor Response Send shade to favorite position Approx. 8.3 Delete favorite position Press P2 on controller. Motor Response ROLLEASE ACMEDA Press STOP on controller. Motor Response Press STOP on controller.
9 TILT & ROLLER MODE 9.1 Toggle motor to Tilt Mode Default motor mode is Roller after initial Limits have been set, use following steps to change to Roller Mode. Hold UP & DOWN on controller. Motor Response Approx. 9.2 Press STOP on controller. Motor Response 5 SECS Toggle Motor to Roller Mode If motor is in Tilt Mode, use following steps to change to Roller Mode. Hold UP & DOWN on controller. Motor Response Approx. Press STOP on controller.
10 ADJUSTING SPEED 10.1 Increase Motor Speed Default motor mode is the slowest speed. Press P2 Motor Response Press UP Motor Response Press UP Motor Response 10.
11 SOFT STOP CONFIGURATION 11.1 Turn Soft Stop OFF Motor must be in slowest speed to turn Soft Stop OFF. Press P2 Motor Response Press DOWN Motor Response Press DOWN Motor Response 11.2 Turn Soft Stop ON Motor must be in fastest speed to turn Soft Stop ON.
12 BATTERY CHECK FUNCTION 12.1 Send Shade to battery charge level Shade must be at Upper Limit. Hold UP Upper Limit Lower Limit Motor Response Approx. 13 5 SEC Shade must be at Upper Limit Hold UP for Approx. 5s Percentage of Battery Charge Remaining Percentage Depleted Shade moves to percentage of battery charge remaining CHARGING LED 13.1 Turn Charging LED ON/OFF Motor must be at Lower Limit. Hold DOWN to toggle off Motor Response Approx.
14 9 SLEEP MODE SLEEP MODE If multiple motors are grouped on a single channel, Sleep Mode may be used to put all but 1 motor to sleep, allowing programming of just the one motor that remains “Awake”. See page 6 for detailed P1 functions. Enter Sleep Mode Sleep mode is utilized to prevent a motor from incorrect configuration during other motor setup. Hold P1 button on the motor head Motor Response Exit Sleep Mode: Method 1 Exit Sleep Mode: Method 2 Exit sleep mode once the shade is ready.
