PRODUCTS Hybrid IC TYPE PAGE 22/33 BP35C5 19. RECOMMENDED REFLOW CONDITION Peak temp. 230~255℃ Ramp rate(Avg.) < 4℃/sec 220℃ 180℃ Time above 220℃ 40sec (30~90sec) 150℃ Time between A-B 80sec (60~120sec) Point A Ramp rate(Avg.
PRODUCTS Hybrid IC TYPE PAGE 23/33 BP35C5 20. PACKING (TBD) 20.1 Taping dimensions UNIT: mm Symbol Dimensions (mm) Tolerance (mm) A0 15.55 B0 19.4 D0 1.5 D1 2.0 E 1.75 F 14.2 P0 4.0 P 20.0 P2 2.0 K0 3.2 S 28.4 t 0.35 W 32.0 ±0.1 ±0.1 +0.1 /0.0 MIN. ±0.1 ±0.1 ±0.1 ±0.1 ±0.1 ±0.1 ±0.1 ±0.05 ±0.3 Pocket: PS, Cover tape: PE 20.2 Taping packaging specification Pull-Out direction of taping and direction of pin 1 are shown below.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 24/33 20.3 Packaging method Carrier tape Reel Box label Desiccant Humidity indicator card Foil bags Box label REV. E TSZ22111・05・002 SPECIFICATION No.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 25/33 Box label (1) Foil bags Box (2) label Box label Middle Carton Material: B Flute Packing slip Carton (4000 pcs/1 CTN) Material: AB Flute Box label REV. E TSZ22111・05・002 SPECIFICATION No.
PRODUCTS Hybrid IC TYPE PAGE 26/33 BP35C5 20.4 Reel Dimensions Reel size/ Tape size Dimensions (mm) Tolerance (mm) A B C D W t T MAX 330 100 13.3 2.5 32.5 2.0 36 ±2.0 ±2.0 ±1.0 ±0.5 +2.0/ -0.0 ±0.5 +2.0/ -1.0 REV. E TSZ22111・05・002 SPECIFICATION No.
PRODUCTS Hybrid IC 20.5 TYPE BP35C5 PAGE 27/33 Leader and Trail Tape There will be 40 pockets at Leader tape. Leader tape part リーダー部 Empty 空部 Reel side Pulling-out side 80cm (about 40 pockets in 40ポケット以上 the front) There will be 10 pockets at Trail tape. The end of Trail tape is not fixed to Reel. Empty 空部 Reel side Pulling-out side 20cm (about 10pockets in the10ポケット以上 tail) 20.6 Missing product ratio Rate of incident Consecutive missing products Non-Consecutive missing products 20.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 28/33 20.8 Peel-off strength of Cover Tape Peel-off strength of Cover tape is: 0.1~0.7N (10gf~70gf) with peeling speed of 300mm/min. 165~180° 165 ~ 180° 300mm/min 300mm/min 20.9 Packing Label The label with following things is stuck at the packing case. ① Type name (BP35C5) ② Quantity ③ Lot No.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 29/33 21. Product Weight 1.4 gram 22. Manufacturing Country China 23. Precautions for Use 1) This product allows the reflow process only once. (with ROHM’s recommended reflow condition) During the reflow process, the solder inside the product may be re-fused or re-melt. Please note this and pay special attention. 2) If this product is laid neglected, it will absorb moisture from the surrounding environment.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 30/33 24. Precautions as Radio Equipment 24.1. For Japan region (ARIB STD-T108) BP35C5 has acquired the “Construction design certification” (Article 38-24 (1) of the Radio Act) for “Radio Equipment: Specified low power equipment of less than 13 GHz prescribed in Article 2-1 (8) Type of Specified Radio Equipment.” Consequently, BP35C5 is available for use as radio equipment only in Japan without making an application for radio station license.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 31/33 1. LABELING AND USER INFORMATION REQUIREMENTS The BP35C5 module has been labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside another device, then the outside of the finished product into which the module is installed must also display a label referring to the enclosed module.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 32/33 3. APPROVED EXTERNAL ANTENNA TYPES To maintain modular approval in the United States, only the antenna types that have been tested shall be used. It is permissible to use different antenna manufacturer provided the same antenna type and antenna gain (equal to or less than) is used. Testing of the BP35C5 module was performed with the antenna types listed in Table 1 Tested External Antenna Types. TABLE 1: Tested External Antenna Types Type Dipole Gain (dBi) +3 4.
PRODUCTS Hybrid IC TYPE BP35C5 PAGE 33/33 25. Firmware 25.1 Firmware licensing With respect to the built-in firmware of this Product, agree to the following licensing prior to use. 1) 2) 3) 4) 5) 6) 7) 8) 9) This software is firmware dedicated to BP35C5. Do not use the firmware for any product other than BP35C5. Do not assign, transfer, sub-license, or lend this Software to any third parties. Reverse engineering, decompilation, disassembly, reproduction, and change of this Software are prohibited.