NT2-A Instruction Manual www.rodemic.com 037-950-1-1_NT2-Akit_manual.
Introduction We at the would like to thank you for investing in NT2-A Multi-Pattern Large Diaphragm Condenser Microphone. The NT2-A carries on the tradition forged by the legendary NT2. It was recognised as the World’s Best Studio Microphone by the MIPA in 2006, in addition to being awarded the Electronic Musician Editor’s Choice.
Specifications Acoustic Principle: Pressure, Pressure gradient Directional Pattern: Three position variable - Omni, Cardioid or Figure 8 (see graph) Frequency Range: 20 Hz - 20 kHz (see graph) Output Impedence: 200Ω Sensitivity: -36 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB @ 1kHz Equivalent Noise: 7dBA SPL (per IEC651) Maximum Output: +16dBu (@ 1kHz, 1% THD into 1KΩ load) Dynamic Range: 140 dB (per IEC651, IEC268-15) Maximum SPL: 147dB SPL (@ 1kHz, 1% THD into 1KΩ load) (157dB with
Specifications Frequency Response 20 dB re 1 V/Pa 10 0 -10 -20 -30 20Hz 100 1000 10 000 20 000 10 000 20 000 Cardioid 20 dB re 1 V/Pa 10 0 -10 -20 -30 20Hz 100 1000 Omni Polar Response 037-950-1-1_NT2-Akit_manual.
Features • Large 1” gold sputtered capsule • On-body control of polar pattern, HPF and PAD • Three position variable polar pattern Omni, Cardioid or Figure 8 • Three position variable High-Pass Filter Flat, 40Hz or 80Hz • Three position PAD - 0dB, -5dB or -10dB • Ultra low noise, transformerless surface mount circuitry • Wide dynamic range • Internal capsule shock mounting • Made in Australia • Full 10 Year warranty* Accessories SM6 Shock mount (including studio grade pop shield) Microphone sleeve/ dustc
Using the NT2-A • The NT2-A is a phantom powered microphone. To operate correctly it requires a 48V phantom supply from the mixing console or other source. • Please ensure all cable connections are secure before applying power to the microphone, and allow a few moments for the microphone to stabilise after the power is turned on. • The gold dot on the face of the NT2-A indicates the front of the microphone, and the pick-up area of the cardioid pattern.
Using the NT2-A • Microphone technique, or how to get the sound you want, requires experimentation. We suggest that you start with the channel EQ set to ‘OFF’ or ‘FLAT’ (no boost or cut). Try to get the sound you want by placing either reflective or absorbent panels at various angles adjacent to the source being recorded. • Changing the acoustic properties of the space around the microphone is our recommended initial approach for obtaining best sound quality.
Setting the Polar Pattern The NT2-A polar pattern can be adjusted to either omni, through cardioid or figure of eight. This flexibility allows for more versatile recording of vocals, instruments and sound sources. After making a selection change, allow a few moments for the microphone to stabilise. Selector Switch • Select the polar pattern via the top selector switch on the NT2-A body.
Setting the Polar Pattern • When in the omni position (lower position), the microphone picks up sound from all around the microphone and there is less proximity effect than in cardioid mode. (Proximity Effect is an increase in lower (bass) frequencies when the sound source is ‘close’ to the microphone). The omni pattern is commonly used for room (ambient) miking or to record a more natural sound when close miking instruments.
Setting the High-Pass Filter The High-Pass Filter setting can be used to reduce the microphone’s sensitivity to low frequency sounds, and is useful when you wish to avoid additional noise and vibration from outside traffic, air conditioning and machinery, foot tapping etc. The middle selector switch on the front of the NT2-A can be used to set the High-Pass Filter to 0Hz/Flat (center position), 40Hz (lower position) or 80Hz (upper position).
Settings Reminder You may wish to keep a record of the settings you have made during a recording. Should you wish to recreate a section of a recording, or to capture the same “sound quality”, you can refer to the manual and easily retrieve the mic’s previous settings. Date: / Date: / / / Description: Description: Date: Date: / / / / Description: Description: Date: Date: / / Description: 037-950-1-1_NT2-Akit_manual.
Support If you experience any problem, or have questions regarding your microphone, first contact the dealer who sold it to you. We have an extensive dealer network to assist you. If you have difficulty getting the advice or assistance you require from the dealer, do not hesitate to contact us directly via the details below. International 107 Carnarvon Street Silverwater NSW 2128 Australia Ph: +61 2 9648 5855 Fax: +61 2 9648 2455 USA P.O.
