Installation assistance available at: POWERED ENCLOSURE www.rockfordfosgate.com/rftech P300-8P P300-10 P300-10T P300-12 P300-12T P500-12P 102418JF 1230-71030-02 Printed In Thailand Serial Number: 600 South Rockford Drive • Tempe, Arizona 85281 United States Direct: (480) 967-3565 • Toll Free: (800) 669-9899 R O C K F O R D F O S G AT E .
Introduction Dear Customer, Congratulations on your purchase of the world’s finest brand of car audio amplifiers. At Rockford Fosgate we are fanatics about musical reproduction at its best, and we are pleased you chose our product. Through years of engineering expertise, hand craftsmanship and critical testing procedures, we have created a wide range of products that reproduce music with all the clarity and richness you deserve.
Specifications P300-10 Model Description 10” Powered Subwoofer Power Rating (RMS/Peak) 300W / 600W Crossover Slope 12dB/Oct Crossover Variable 50Hz-200Hz Frequency Punch Bass Variable 0 - +12dB @ 45Hz Frequency 35Hz - 200Hz Response P300-12 P300-8P 12” Powered Subwoofer 8” Powered Subwoofer 300W / 600W 300W / 600W 12dB/Oct 12dB/Oct Variable 50Hz-200Hz Variable 50Hz-200Hz Variable 0 - +12dB @ 45Hz Variable 0 - +12dB @ 45Hz 35Hz - 200Hz 35Hz - 200Hz 100mV - 3V 100mV - 3V Fuse Rating 20A (2
Specifications [5.98] 152.0 [17.91] 455 [0.59] 15 P300-10 [13.31] 338 [8.82] 224.0 [9.85] 250 [19.80] [7.08] 180 P300-12 [14.96] 380 [10.94] 278 [12.1] 307 3.7 94 17.6 448 1.5 38 11.4 289 P300-8P illus.-1.1 4.8 123 5.
Specifications 21.7 552 4.8 122 P300-10T 13.3 338 7.5 190 7.9 201 4.8 122 25.8 656 15.0 380 P300-12T 8.
Design Features Input Level Phase Switch Allows you to select the output phase of the amplifier between 0° and 180°. Set the Input Level switch to match the outputs of your source unit.(LO - RCA or HI - Speaker Level) Auto Turn On Three different automatic turn-on modes can be selected; REM(+12V), DC Offset, and Audio. Gain Control The input gain control is preset to match the output of most source units.
Installation Contents • Punch Powered Loaded Enclosure • RCA/Speaker Harness 9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12V power wire within 18” (45.7 cm) of the battery terminal.
Installation 2. Prepare the RED wire (power cable) for attachment to the amplifier by stripping 1/2” of insulation from the end of the wire. Insert the bared wire into the B+ terminal of the power connector and tighten the set screw to secure the cable in place. NOTE: The B+ cable MUST be fused 18” or less from the vehicle’s battery. Install the fuseholder under the hood and ensure connections are water tight. 3.
Operation/Troubleshooting Adjusting Gain Troubleshooting 1. Turn amplifier gain to minimum (counter-clockwise). 2. Turn the source unit volume up to 7/8 maximum (or when distortion is just inaudible). 3. Slowly increase amplifier gain control until adequate volume is achieved. NOTE: If you are having problems after installation follow the Troubleshooting procedures below. Step 1. Check Amplifier for proper connections. Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue.
Warranty Rockford Corporation offers a limited warranty on Rockford Fosgate products on the following terms: Length of Warranty Speakers, Signal Processors, PRIME and PUNCH Amplifiers – 1 Year POWER Amplifiers – 2 Years Any Factory Refurbished Product – 90 days (receipt required) What is Covered This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford Fosgate Dealers in the United States of America or its possessions.