RF-WHD200_10-1353_MAN_ENG_V3.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 2 Monday, March 14, 2011 3:45 PM Rocketfish RF-WHD200 4-Port WirelessHD Kit Contents Safety information .......................................................... 3 Features............................................................................... 4 Setting up the HDWireless Kit..................................... 9 Using the WirelessHD Kit ............................................13 Specifications................................................................
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 3 Monday, March 14, 2011 3:45 PM Safety information The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 4 Monday, March 14, 2011 3:45 PM • Only use attachments or accessories specified by the manufacturer. • Unplug the included devices during lightning storms or when unused for long periods of time. • Refer all servicing to qualified service personnel.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 5 Monday, March 14, 2011 3:45 PM Transmitter front/top panel Item Description 1 2 3 4 5 HDMI 4—When the indicator is on this HDMI port is in use. HDMI 3—When the indicator is on this HDMI port is in use. HDMI 2—When the indicator is on this HDMI port is in use. HDMI 1—When the indicator is on this HDMI port is in use. Power and link status indicator ( ) • Blinking—The power is on and the receiver is searching for the transmitter or is in sleep mode.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 6 Monday, March 14, 2011 3:45 PM Receiver front/top panel 1 Item Description 1 Power and link status indicator ( ) • Blinking—The power is on and the receiver is searching for the transmitter or is in sleep mode. • On—The transmitter and receiver are linked. • Off—The power is off. Transmitter back panel Item Description 1 2 3 4-7 6 DC IN jack—Connect the power adapter labeled “transmitter” to this jack. Power switch—Turns the transmitter on or off.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 7 Monday, March 14, 2011 3:45 PM Receiver back and side panels Right side view Back view Left side view Item Description 1 2 3 4 HDMI jack—Connect this port to an HDMI input on the TV or projector, using a high-speed HDMI cable. DC IN jack—Connect the power adapter labeled “Receiver” to this jack. Power switch—Turns the receiver on or off. Cable routing clips - Insert HDMI cable into these clips for receiver placement stability.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 8 Monday, March 14, 2011 3:45 PM Remote control Note: Remote control design subject to change. Item Description 1 2-5 SLEEP button -Press to put the WirelessHD receiver and transmitter into sleep mode; or to "wake" them up from sleep mode if they do not automatically do so on their own (this functionality varies by brand and model of connected components). Be sure to point the remote toward each one separately.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 9 Monday, March 14, 2011 3:45 PM Setting up the HDWireless Kit Setup tips: - Test the placement of the transmitter and receiver for a good signal prior to permanently mounting or installing everything.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 10 Monday, March 14, 2011 3:45 PM Connecting the WirelessHD transmitter and receiver To connect the WirelessHD transmitter and receiver: 1 Connect up to 4 HDMI enabled source components, such as a Blu-ray/DVD player, cable/satellite box, gaming console, laptop, etc., to the HDMI input jacks on the transmitter, using high-speed HDMI cables.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 11 Monday, March 14, 2011 3:45 PM 2 Connect the display device, such as a TV or projector, to the receiver with a high-speed HDMI cable. Receiver HDMI cable Display devices OR 3 Connect the AC power adapters to the transmitter and receiver and to power outlets. Note: The included AC adapters are labeled “Receiver” and “Transmitter,” to ensure that the correct adapter is used for each device.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 12 Monday, March 14, 2011 3:45 PM 6 Power on the WirelessHD transmitter and receiver. The HDMI input port LED on the transmitter should light continously (stop blinking) to indicate that the desired input is selected with active video. If this selection does not occur automatically, please use the included remote control or HDMI Select Switch on back of the transmitter to select the desired input port. See step 5 in “Using the WirelessHD Kit” section on page 13.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 13 Monday, March 14, 2011 3:45 PM 2 Using appropriate wall anchors and screws (not included) for the type of wall or ceiling where the receiver will be mounted, securely attach the receiver mounting bracket to the wall. 3 Mount the receiver onto the mounting bracket by sliding the slots on the bottom of the receiver downward onto the tabs on the bracket.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 14 Monday, March 14, 2011 3:45 PM 3 Power on the source component you wish to view. 4 Power on the WirelessHD transmitter. 5 Switching the WirelessHD transmitter to the correct HDMI input: Note: When switching between the four HDMI ports, it is normal for the switching to take an average of about 10 seconds (sometimes up to 20 seconds; the further the WirelessHD transmitter and receiver are from each other, the longer the switching will take).
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 15 Monday, March 14, 2011 3:45 PM 6 To turn the WirelessHD kit off, perform one of the following steps: • Power off your TV or projector and source devices - when the WirelessHD transmitter and receiver have not detected a signal, they will automatically go into sleep mode. Note: When the WirelessHD transmitter and receiver go into sleep mode, the power and link status LEDs on both units will blink slowly.
RF-WHD200_10-1353_MAN_ENG_V3.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 17 Monday, March 14, 2011 3:45 PM Troubleshooting Symptom Possible Solutions Receiver will not link to Transmitter • For best performance, mount the receiver on the wall next to the TV (or on the ceiling next to a projector) with a clear view of the room. It should NOT be mounted behind the TV or projector.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 18 Monday, March 14, 2011 3:45 PM Symptom Possible Solutions No video and/or audio Remote control does not operate components 18 • If the power LEDs on the transmitter and receiver are blinking, the adapters are not linked. See “Receiver will not link to Transmitter” troubleshooting steps above.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 19 Monday, March 14, 2011 3:45 PM Specifications Standards WirelessHD, HDMI (V1.4a 3D) Frequency 60 GHz Input/Output interface HDMI Antenna type 32-antenna array (integrated ceramic) Range 32.8 ft. (10 m) AV port Dimensions Weight AC power adapter Operating environment (total system) Transmitter: 4 ports (CEC pass-through) Receiver: 1 port (CEC pass-through) Transmitter: 7.39 x 6.18 x 2.17 in. (187.6 x 157.0 x 55.2 mm) Receiver: 6.06 x 4.72 x 1.89 in. (154.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 20 Monday, March 14, 2011 3:45 PM Video format Vertical refresh Color space Sampling Bits/pixel 50 Hz YCbCr 59.94/60 Hz RGB YCbCr 50 Hz RGB YCbCr 59.94/60 Hz RGB YCbCr 23.976/24 Hz RGB YCbCr 50 Hz RGB YCbCr 59.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 21 Monday, March 14, 2011 3:45 PM 3D video support list Frame packing Top-to-bottom Side-by-side 1080p@23.98/24 Hz 720p@50/59.94/60 Hz 1080p@23.98/24 Hz 720p@50/59.94/60 Hz 1080i@50/59.94/60 Hz Audio format Audio up to 8-channel, 24-bit 192 kHz LPCM, surround sound audio (6/8 channel PCM, Dolby Digital, DTS). Audio sample rate, F’s LPCM 2/6/8-channels Multiple of Fs LPCM 2-channel DTS and Dolby Digital 2/6 channels 32 kHz 44.1 kHz 48 kHz 88.2 kHz 96 kHz 128 4.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 22 Monday, March 14, 2011 3:45 PM • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 23 Monday, March 14, 2011 3:45 PM One year warranty Rocketfish Products (“Rocketfish”) warrants to you, the original purchaser of this new RF-WHD200 (“Product”), that the Product shall be free of defects in the original manufacture of the material or workmanship for one (1) year from the purchase of the Product (“Warranty Period”). This Product must be purchased from an authorized dealer of Rocketfish brand products and packaged with this warranty statement.
RF-WHD200_10-1353_MAN_ENG_V3.
RF-WHD200_10-1353_MAN_ENG_V3.fm Page 28 Monday, March 14, 2011 3:45 PM www.rocketfishproducts.com (800) 620-2790 Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN 55423-3645 USA © 2011 BBY Solutions, Inc. All rights reserved. ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and brand names are trademarks of their respective owners.