40" to 75" TV WALL MOUNT - FULL MOTION RF-HTLF23 ASSEMBLY GUIDE Before using your new product, please read these instructions to prevent any damage.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Dimensions . . . . . . . . . . . . . . . . . . .
RF-HTLF23 Specifications • • • • • Maximum TV weight: 100 lbs. (45.3 kg) Screen size: From 40 in. to 75 in. (101.6 cm to 190.5 cm) diagonal Overall dimensions (H × W): 17.7 × 25.1 in. (45 cm × 63.9 cm) Wall-mount weight: 18.8 lbs. (8.5 kg) For customer service, call: 1-800-620-2790 Dimensions 25.14" (63.9 cm) 17.72" (45 cm) Need help? Call 1-800-620-2790 (U.S.
Tools needed You need the following tools to assemble your new TV wall mount: Level Measuring tape Pencil Drill Phillips screwdriver Socket wrench with 1/2" (13 mm) socket or adjustable wrench Tape Wood Stud Wall Edge-to-edge stud finder 4 7/32" (5.5 mm) wood drill bit Concrete or Concrete Block Wall Hammer 3/8" (10 mm) masonry drill bit Need help? Call 1-800-620-2790 (U.S.
RF-HTLF23 Package contents Make sure that you have all the hardware necessary to assemble your new TV wall mount: 04 Horizontal bracket (2) 07 Template (1) 05 Vertical bracket (1) 08 Wall plate (1) 11 Arm assembly (1) Need help? Call 1-800-620-2790 (U.S.
TV Hardware Lbl. Hardware # Lbl. Hardware M6 × 12 mm screw # 4 4 Spacer (2.5 mm) 03 M6 × 35 mm screw 4 4 Spacer (22 mm) 01 M8 × 16 mm screw 4 06 M8 × 25 mm screw 4 09 4 10 Lag screw 5/16 × 2 3/4 in. 4 4 4 Washer 5/16 in. M8 × 35 mm screw M8 × 50 mm screw M5 × 10 mm TV interface screw 4 1 12 Locking screw 10-32 × 3/8 in. M6/M8 washer 02 4 13 Wall plate screw 10-24 × 1 1/4 in. 14 1 5/32 in. hex key 6 2 Need help? Call 1-800-620-2790 (U.S.
RF-HTLF23 Concrete Installation Kit CMK1 (not included) Contact customer service at 1-800-359-5520 to have these additional parts shipped directly to you. Lbl. Hardware # C1 Lag screw 5/16 × 2 3/4 in. 4 C2 Washer 5/16 in.
• Obstructed back: The brackets block any of the jacks on the back of your TV. You need 2.5 mm or 22 mm spacers (03) when assembling the wall mount. • Irregularly-shaped back: There is a gap between the brackets and some part of the back of your TV. You need 2.5 mm or 22 mm spacers (03) when assembling the wall mount. 6 8 Remove the brackets. Need help? Call 1-800-620-2790 (U.S.
RF-HTLF23 STEP 2 - Select screws, washers, and spacers 1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If screws came with your TV, they are almost always in the holes on the back of your TV.) If you don't know the correct length of the mounting screws your TV requires, test various sizes by hand threading the screws.
STEP 3 - Option 1: Attaching the horizontal brackets to a TV with a flat back CAUTION: To avoid personal injury or property damage, do not use power tools. 1 2 3 Align the holes you noted on the horizontal brackets (04) with the screw holes on the back of your TV. Place the washers (02) over the holes in the brackets that align with the screw holes on the back of your TV, then insert the screws that you selected in STEP 2 (01) through the washers. Make sure that the brackets are level.
RF-HTLF23 STEP 3 - Option 2: Attaching the horizontal brackets to a TV with irregular or obstructed back CAUTION: To avoid personal injury or property damage, do not use power tools. 1 2 3 Place the spacers you selected in STEP 2 (03) over the screw holes on the back of your TV. Align the horizontal brackets (04) over the spacers, then place the washers (02) over the holes in the brackets. Insert the screws you selected in STEP 2 (01) through the washers, brackets, and spacers.
STEP 4 - Attaching the vertical bracket 1 2 CAUTION: To avoid personal injury or property damage, do not use power tools. Lay the vertical bracket (05) on top of the horizontal brackets (04). Make sure that the bracket is centered. Secure the vertical bracket to the horizontal brackets with the TV interface screws (06). Tighten the screws until they are snug against the vertical brackets. Do not over tighten.
RF-HTLF23 STEP 5 - Determine wall-mount location Note: Your TV should be high enough so your eyes are level with the middle of the screen from a seated position (normally, 40 to 60 inches from the ground). For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder The center of your TV will match the center of the wall plate (08).
STEP 6 - Option 1: Installing on a wood stud wall Note: Drywall covering the wall must not exceed 5/8" (16 mm). 1 2 Locate the stud, then verify the center of the stud with an edge-to-edge stud finder. Make sure that the distance between the studs is 16 in. (40.6 cm). Note: Drywall covering the wall must not exceed 5/8 in. (1.6 cm). Minimum wood stud size: nominal 2 × 4 in. (5.1 × 10.2 cm) actual 1 1/2 × 3 1/2 in. (3.8 × 8.9 cm). 16" (40.
RF-HTLF23 3 Align the center of the wall plate template (07) at the height you determined in the previous step and make sure that it is level. Tape the template to the wall. 2 3/4 in (69 mm) 7/32 in (5.5 mm) 07 4 Drill four pilot holes through the template to a depth of 2 3/4 in. (7 cm) using a 7/32 in. (5.5 mm) diameter drill bit, then remove the template. 2 3/4 in. (7 cm) Need help? Call 1-800-620-2790 (U.S.
5 Align the wall plate (08) with the pilot holes, insert the lag screws (09) through washers (10) and into the holes in the wall plate, then tighten the lag screws only until they are firm against the wall plate assembly. 09 10 08 CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag screws (09). 16 Need help? Call 1-800-620-2790 (U.S.
RF-HTLF23 STEP 6 - Option 2: Installing on a solid concrete or concrete block wall CAUTION: To prevent property damage or personal injury, never drill into the mortar between the blocks. Mount the wall plate directly onto the concrete surface. 1 Align the center of the wall plate template (07) at the height you determined in the previous step and make sure that it is level. Tape the template to the wall. 07 Note: Mount the wall plate (08) directly onto the concrete surface (no wall covering).
2 Drill pilot holes to a depth of 3 in. (7.6 cm) using a 3/8 in. (10 mm) diameter masonry drill bit, then remove the template. 3 in. (76 mm) 07 3 Insert the concrete wall anchors (C3) (see Concrete Installation Kit CMK1 (not included) on page 7) into the pilot holes and use a hammer to make sure that the anchors are flush with the concrete surface. C3 18 Need help? Call 1-800-620-2790 (U.S.
RF-HTLF23 4 Align the wall plate (08) with the anchors, insert the lag screws (C1) through the washers (C2) and into the holes in the wall plate assembly, then tighten the lag screws only until they are firm against the wall plate. CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag screws (C1). C2 C1 08 Need help? Call 1-800-620-2790 (U.S.
STEP 7 - Attach the arm assembly to the wall plate 1 Hang the arm (11) onto the wall plate (08) by first hooking the top of the arm assembly into the wall plate channel, then lowering the bottom of the assembly into place. 11 08 You’ll need 13 Wall plate screw (2) 14 Hex key 11 Arm assembly (1) 20 Need help? Call 1-800-620-2790 (U.S.
RF-HTLF23 2 Use the hex key (14) to secure the arm assembly to the wall plate (08) with the wall plate screws (13). CAUTION: These wall plate screws must be installed to secure your TV onto the wall plate assembly. 13 14 08 11 Need help? Call 1-800-620-2790 (U.S.
STEP 8 - Attach your TV to the arm assembly 1 Hang your TV onto the arm assembly (11) by first hooking the top support of the vertical bracket (05) onto the assembly, then resting your TV into place. You hear an audible click when your TV is in place. 05 05 11 11 You’ll need 12 locking screw (1) 22 14 Hex key Need help? Call 1-800-620-2790 (U.S.
RF-HTLF23 2 Use the hex key (14) to lock your TV to the arm assembly with the locking screw (12). IMPORTANT: The locking screw must be installed to secure your TV onto the arm assembly. 05 HEAVY! You may need assistance with this step. 11 12 14 Need help? Call 1-800-620-2790 (U.S.
STEP 9 - Managing cables • Fully extend the arm assembly (11) to provide enough slack, then routing cables along the arms and inserting them into the channels on the arms to provide a clean look to your installation. 11 STEP 10 - Adjust tilt Note: After your TV is in place, tighten the tilt tension knob to prevent unwanted movement. • Loosen the tension knob with your fingers or the hex key (14), adjust the tilt angle, then tighten the knob to keep your TV in place.
RF-HTLF23 STEP 10 - Adjust the level 1 2 3 Loosen the locking screw (12). Turn the leveling screw (L) with a Phillips screwdriver to level your TV. Retighten the screw (12). 12 12 14 L 14 Removing your TV from the wall mount 1 2 3 Disconnect all cables, then pull down the release cord located below the vertical bracket to unlock your TV from the vertical bracket. Use the hex key (14)to remove the locking screw (12) from the arm assembly (see STEP 8 - Attach your TV to the arm assembly on page 22).
LIFETIME LIMITED WARRANTY Definitions: The Distributor* of Rocketfish branded products warrants to you, the original purchaser of this new Rocketfish-branded product ("Product"), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product ("Warranty Period").
RF-HTLF23 • • • • • Accidental damage Misuse Abuse Negligence Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or apartment complex, or otherwise used in a place of other than a private home. • Unauthorized modification of any part of the Product, including the antenna • Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in).
Part # 6907-302025 www.rocketfishproducts.com 1-800-620-2790 (U.S. and Canada) ROCKETFISH is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2019 Best Buy. All rights reserved.