Document #5 Centeron™ Ultrasonic Monitor Instruction Manual Model: UM Series Document # 039935A0001 Revision #C Dated 11/07/2000 SRE (ovens U.S.A. ~ Roberts haw industrial Products Division, 1602 Mustang Drive, Maryellen, Tennessee 37801 885-981-3100 + Fax: 865-981-3168 www. Center on net The product described within contains RF technology licensed through Axon Sor. under the following patents: 5,067,136 5,095,483 5.457.
Notice The information contained in this document is current as of the date of publication but is subject to change without notice. Roberts haw makes no warranty, expressed or implied, with regard to this material, including but not limited to the implied warranties of merchant ability and fitness for a particular purpose.
ST : . SEN Centeron™ Ultrasonic Monitor Instruction Manual Centeron™ Ultrasonic Monitor Instruction Manual List of Acronyms i 1.0 Introduction This manual describes how to install, test, and service the Centerfold Ultrasonic Monitor.
ons a _ Centeron™ Ultrasonic Monitor Instruction Manual Centeron™ Ultrasonic Monitor Instruction Manual Figure 1. Centeron™ Monitor Label Product Markings 24.1.5 Product Safety Markings and Text Field The commercial and industrial markets require products to meet certain safety CE] requirements and to be marked appropriately. See Section 2.4.2 for more Center on information on safety certifications, : 202021 21.
Centeron™ Ultra Sonic Monitor Instruction Manual 24 Certifications 24.1 FCC Notice—Radio Frequency Communications The Monitor generates and uses radio frequency energy. If not installed and used in accordance with the manufacturer's instructions, it may cause interference to radio and television reception. The Monitor board has been tested and found to comply with the specifications in Part 15 of Radiators and FCC Rules for Class B Computing Devices.
Ceateron™ Ultra Sonic Monitor Instruction Manual * Windows and wooden doors can provide radio signals access into otherwise closed metal buildings. However, “low-E” window glass may have a thin metallic coating which can reflect radio signals. * Strong electromagnetic fields such as those found in close proximity to power lines, large electric motors, generators, electric fences, and transmitter antennas may interfere with the radio signals received by the Centeron™ Controller.
Centeron™ Ultrasonic Monitor instruction Manual + To activate the Monitor, pull the disable magnet completely out of the top of the Monitor housing. This will activate the Monitor 10 make measurements and burst transmissions on a factory programmed interval . Note: The installer can limit the number of Controller calls during multiple Monitor installs by removing each additional Monitor magnet within 30 seconds of the last one.
Canteron™ Ultrasonic Monitor Instruction Manual Question Does the Monitor occasionally miss scheduled report times (i.e, The Controller reports “lost Monitor” to the Data Collection System)? Does the Monitor ever report a low battery status? Does the Monitor aver report error codes? Solution with the Monitor end resting on a flat surface near the Controller installation location. If successful only at bench testing, re-evaluate the installation site tor RF interference problems per Section 3.
Centeron™ Ultrasonic Monitor Instruction Manual 2. Insert the disable magnet into the sot of the Monitor's upper housing until snug. 3. If testing with the Monitor at the location site, it will be necessary to have one person activate the Monitor while another watches for a response at the Controller. If bench testing, the same person can locate the Monitor close to the Controller in order to watch for a response. Activate the Monitor by completely removing the disable magnet from the upper housing. 4.
Centeron™ Ultrasonic Monitor Instruction Manual Note: The mounting screws are not evenly spaced around the upper housing in order to insure that the housing will only fit in the proper orientation, 10. Using a Phillips screwdriver, gently tighten the 3 screws on the Ultrasonic Monitor housing to 10+/~ 2 inch pounds. Do not over tighten. 11. Re-install the monitor on the tank. 12. Follow the battery manufacturers’ safety and disposal guidelines. 5.
Centeron™ Ultrasonic Monitor Instruction Manual Appendix C: Product Drawing Figure 7. Monitor Drawing 3 smart 208 Tine ¥ Sauna’ Sgn + 73a Tote amour tannest Roberts haw industrial Products Page C-1 14/07/2000 Centeron™ Ultrasonic Monitor Instruction Manual Appendix D: Site Survey Form Figure 8.