CLN ILB Full Spectrum Regulatory Requirements Requirement 1 FSS external label must be same as Bosch label (submitted to FCC & IC) FCC ID: PFJCLNFIA15001 IC ID: 909C-CLNFIA15000 Automotive Electronics 1 AE/EME1-NA | 6/28/2013 | © 2013 Robert Bosch LLC and affiliates. All rights reserved.
CLN ILB Full Spectrum Regulatory Requirements Requirement 2 Must be included in Full Spectrum User Manuals. “Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment”. Automotive Electronics 2 AE/EME1-NA | 6/28/2013 | © 2013 Robert Bosch LLC and affiliates. All rights reserved.
CLN ILB Full Spectrum Regulatory Requirements Requirement 3 Full Spectrum User Manuals must include this verbiage NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CLN ILB Full Spectrum Regulatory Requirements Requirement 4 Full Spectrum User Manuals must include this verbiage. "WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operations at closer distances than this are not recommended." Automotive Electronics 4 AE/EME1-NA | 6/28/2013 | © 2013 Robert Bosch LLC and affiliates.
CLN ILB Full Spectrum Regulatory Requirements Requirement 5 Full Spectrum User Manuals must include this verbiage. Manufacturers of RF lighting devices must provide an advisory statement, either on the product packaging or with other user documentation, similar to the following: This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communication equipment operating between 0.4530 MHz.
CLN ILB Full Spectrum Regulatory Requirements Requirement 6 User manuals for transmitters shall display the following notice in a conspicuous location: Full Spectrum User Manuals must include this verbiage. Especially important if an external antenna connector is provided at a later date. “Under Industry Canada regulation, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
CLN ILB Full Spectrum Regulatory Requirements Requirement 7 Full Spectrum User Manuals must include this verbiage. Especially important if an external antenna connector is provided at a later date. “This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated.
CLN ILB Full Spectrum Regulatory Requirements Requirement 8 Full Spectrum User Manuals must include this verbiage. Especially important if an external antenna connector is provided at a later date. “This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device”.
CLN ILB Full Spectrum Regulatory Requirements Requirement 9 ***The following statement must appear in the manual for the device** Full Spectrum User Manuals must include this verbiage. “The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Heath Canada’s website www.hc-sc.gc.ca/rpb.
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – FCC 1 Items 7 and 8: FCC ID Label and Location This document can be a photo or drawing showing the identification label clearly (you must be able to see the FCC ID number), and the location on the device. These may be submitted as one document demonstrating both, or two separate documents. Bosch submitted label drawing, so please ensure you use the same label as found on the CLN.
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – FCC 1 Item 9: User’s Manual/Installation Instructions A draft copy of the instructions may be submitted if the actual documentation is not available. The actual document shall be furnished to Compliance Testing when it becomes available. Modules require specific verbiage – please inquire further if this applies to your device.
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – FCC 2 Item 9: User’s Manual/Installation Instructions A draft copy of the instructions may be submitted if the actual documentation is not available. The actual document shall be furnished to Compliance Testing when it becomes available. Modules require specific verbiage – please inquire further if this applies to your device.
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – Canada 1 Canada User’s Manual/Installation Instructions and Requirements: Radio apparatus shall comply with the requirements to include required notices or statements to the user of the equipment with each unit of the equipment model offered for sale. The Required notices are specified in the RSS documents (including RSS-Gen) Applicable to the equipment model.
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – Canada 2 Transmitter Antenna - RSS Gen §7.1.2 User manuals for transmitters shall display the following notice in a conspicuous location: “Under Industry Canada regulation, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – Canada 3 License-Exempt Radio Apparatus - RSS Gen §7.1.3 – User manuals for license-exempt Radio Apparatus shall contain the following or equivalent notice in a conspicuous location in the user manual or alternatively on the device or both: “This device complies with Industry Canada license-exempt RSS standard(s).
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – Canada 4 Item 22: IC ID Bosch submitted label drawing, so please ensure you use the same label as found on the CLN. Labeling of Certified Radio Equipment Certified radio equipment must be labeled with a unique certification/registration number, which consists of the Company Number (CN), assigned by the Bureau, followed by the Unique Product Number (UPN), assigned by the applicant.
CLN ILB Full Spectrum Regulatory Requirements Backup Documentation – Canada 5 Item 28: RSS 210 Warning Statement for User’s Manual (If applicable) ***The following statement must appear in the manual for the device** Applicable - Full Spectrum User Manuals must include this verbiage.