IMPORTANT: Read Before Using IMPORTANT : Lire avant usage IMPORTANTE: Leer antes de usar Operating/Safety Instructions Consignes de sécurité/d’utilisation Instrucciones de funcionamiento y seguridad GCY30-4 DRAFT Call Toll Free for Consumer Information and Service Locations. Pour obtenir des informations et les adresses de nos centres de service après-vente, appelez ce numéro gratuit.
Safety Symbols The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. ! This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
General Safety Rules Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE All instructions must be read and observed in order to enable work with the GCY30-4 to be carried out safely. Store these instructions in a safe place and provide them when transferring the GCY30-4 or any power tool using it to a third party.
THINK SAFETY SAFETY IS A COMBINATION OF OPERATOR COMMON SENSE AND ALERTNESS AT ALL TIMES WHEN THE PRESSURE WASHER IS BEING USED. FCC Caution The manufacturer is not responsible for radio interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
These guidelines are based on the safety standards previously set by international standard bodies. These standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada This device complies with Industry Canada licence-exempt RSS standard(s).
Getting to Know your GCY30-4 Connectivity Module Product Features The numbering of the product fea- 4 tures refers to the illustrations on the graphics pages. 1 Button cell battery 2 Connectivity module GCY30-4 1 3 Placeholder * 4 Cover of connectivity module* * Part of the power tool Intended Use 2 The connectivity module GCY30-4 enables power tool customization and power tool status check as well as transfer of data and settings based on Bluetooth® wireless tech- 3 nology.
Technical Data Model Operating temperature Storage temperature Dimensions Weight according to EPTA-Procedure 01:2014 Data transmission Bluetooth® Signal Interval Signal Range Power Supply Battery GCY30-4 14 °F…+ 104 °F -4 °F…+ 158 °F 0.275” x 1.18” x 1.18” 0.352 oz Bluetooth® 4.0 (Low Energy)A 8s Maximum 98 ft.B Button cell (3 V lithium battery, CR2032) Battery service life, approx. 36 months System Requirements Mobile terminal device Android 4.
A B The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.1) and support the Generic Access Profile (GAP). The signal range may vary greatly depending on external conditions. The Bluetooth® range may be significantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.). Installing and setting up the app (see figures A1 – A2) Before you can use the GCY30-4, you need to install the Bosch Toolbox app.
After registration is complete, you will receive your access information. – Download the www.bosch-trackmytools.com app/webbased application via the appropriate app store (Apple App Store, Google Play Store) and register using your access information. You can now create and manage your inventory using the app/web-based application. Note: A user account is required in the respective app store. Note: First, fully complete the tutorial for the app.
Assembly Always remove the power tool battery or disconnect the plug from the power source before installation or removal of communications module. Such preventive safety measures reduce the risk of starting the tool accidently. A. Unlock the cover of conA nectivity module 4 on the power tool by turning it counterclockwise with 4 a screwdriver or a large coin. Using unsuitable B objects can damage the electronics or the cover. B. Lift the cover of connectivity module 4 and put it aside. C.
D. Insert the GCY30-4 module 2 into the power tool. Make sure that the terminals inside the tool and the module align. 2 D E. Insert the battery 1 into the GCY30-4 module 2 with the plus terminal facing upwards. It is not necessary to push in the battery.
F. Lower the cover 4 into the tool. G. Lock the cover 4 in place by turning it clockwise with a screwdriver or a large coin until the triangles on the cover and the tool align and the cover clicks in place. G 4 F Operating instructions Once the battery 1 has been inserted, the GCY30-4 will send out a continuous signal. The Bluetooth® signal will only be interrupted if the battery is drained, faulty, or removed. You can find further information directly in the app from Bosch.
Battery Replacement Before the battery is completely used up, the app displays a warning. Chemical Burn Hazard. Keep batteries away from children. This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment.
C. Pull out the used battery 1. Only remove used battery using your fingers. Do not use sharp objects to remove used battery. D. Insert the new battery 1 into the GCY30-4 module 2 with the plus terminal facing upwards. It is not necessary to push in the battery. 1 1 C D E. Lower the cover 4 into the tool. F. Lock the cover 4 in place by turning it clockwise with a screwdriver or a large coin until the triangles on the cover and the tool align and the cover clicks in place.
F 4 E Removing the GCY30-4 (see figures D1 – D2) Do not use force to remove the GCY30-4 2. Do not use any sharp or pointed tools. Note: If needed, turn the power tool around for easier removal of the GCY30-4. Maintenance and Service Maintenance and Cleaning Remove debris with a brush. Do not use any cleaning agents or solvents.
LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from defects in material or workmanship for a period of one year from date of purchase.
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Symboles relatifs à la sécurité Les définitions ci-dessous décrivent le niveau de gravité pour chaque terme signalant un danger. Veuillez lire le mode d’emploi et lire la signification de ces symboles. ! C’est le symbole d’alerte relatif à la sécurité. Il est utilisé pour vous avertir de l’existence possible d’un danger de lésion corporelle. Obéissez à tous les messages relatifs à la sécurité qui suivent ce symbole pour éviter tout risque de blessure ou même de mort.
MISE EN GARDE, conjointement avec le symbole d’alerte en liaison avec la sécurité, indique une situation dangereuse qui, si elle n’est pas évitée, causera une blessure légère ou modérée.
Mise en garde de la FCC : Le fabricant n’est pas responsable des perturbations radioélectriques causées par des modifications non autorisées de ce matériel. De telles modifications pourraient annuler le droit de l’utilisateur de se servir de ce matériel. Cet appareil est conforme à la Partie 15 des Règles de la FCC.
de la radio ou de la télévision – ce qui peut être déterminé en mettant ce matériel sous tension et hors tension – l’utilisateur devrait essayer de remédier à de telles perturbations en prenant une ou plusieurs des mesures suivantes : • Changer l’orientation de l’antenne de réception ou la placer à un autre endroit. • Augmenter la distance entre le matériel et le récepteur. • Brancher le matériel dans une prise de courant faisant partie d’un circuit différent de celui auquel le récepteur est connecté.
Cet appareil et son antenne ne doivent pas être placés au même endroit ou utilisés en même temps que tout autre émetteur ou antenne. Industrie Canada Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
GARANTIE LIMITÉE DES OUTILS ÉLECTRIQUES PORTATIFS ET D’ÉTABLI BOSCH Robert Bosch Tool Corporation (le « vendeur ») garantit à l’acheteur initial seulement que tous les outils électriques portatifs et d’établi BOSCH seront exempts de vices de matériaux ou d’exécution pendant une période d’un an depuis la date d’achat.
AMÉRICAINS, CERTAINES PROVINCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION DE LA DURÉE DES GARANTIES IMPLICITES, IL EST POSSIBLE QUE LES LIMITATIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS. EN AUCUN CAS LE VENDEUR NE SAURAIT ÊTRE TENU POUR RESPONSABLE DES INCIDENTS OU DOMMAGES INDIRECTS (INCLUANT, MAIS NE SE LIMITANT PAS AUX PERTES DE PROFITS) CONSÉCUTIFS À LA VENTE OU L’USAGE DE CE PRODUIT.
Símbolos de seguridad Las definiciones que aparecen a continuación describen el nivel de gravedad de cada palabra de señal de seguridad. Por favor, lea el manual y preste atención a estos símbolos. ! Éste es el símbolo de alerta de seguridad. Se utiliza para alertarle a usted de posibles peligros de lesiones corporales. Obedezca todos los mensajes de seguridad que sigan a este símbolo para evitar posibles lesiones o muerte.
PRECAUCIÓN, cuando se utiliza con el símbolo de alerta de seguridad, indica una situación peligrosa que, si no se evita, causará lesiones leves o moderadas.
Aviso de precaución de la FCC: El fabricante no es responsable de la radiointerferencia causada por las modificaciones no autorizadas que se realicen en este equipo. Dichas modificaciones podrían anular la autoridad del usuario para utilizar el equipo. Este dispositivo cumple con la Parte 15 de las Reglas de la FCC.
diendo el equipo, se recomienda al usuario que intente corregir la interferencia tomando una o más de las medidas siguientes: • Reoriente o reubique la antena receptora. • Aumente la separación entre el equipo y el receptor. • Conecte el equipo a un tomacorriente que esté en un circuito distinto al circuito al que el receptor esté conectado. • Consulte al distribuidor o a un técnico experto en radio/ TV para obtener ayuda.
Industry Canada Este dispositivo cumple con la Parte 15 de las Reglas de la FCC y con el estándar o los estándares RSS exentos de licencia de Industry Canada. Su utilización está sujeta a las dos condiciones siguientes: (1) este dispositivo no podrá causar interferencia perjudicial y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluyendo interferencia que pueda causar un funcionamiento no deseado.
GARANTIA LIMITADA PARA HERRAMIENTAS MECANICAS PORTATILES Y PARA TABLERO DE BANCO BOSCH Robert Bosch Tool Corporation (“el Vendedor”) garantiza, únicamente al comprador original, que todas las herramientas mecánicas portátiles y para tablero de banco BOSCH estarán libres de defectos de material o de fabricación durante un período de un año a partir de la fecha de compra.
LIMITADA A UN AÑO A PARTIR DE LA FECHA DE COMPRA. ALGUNOS ESTADOS DE LOS EE.UU. Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LIMITACIONES EN CUANTO A LA DURACION DE UNA GARANTIA IMPLICITA, POR LO QUE ES POSIBLE QUE LA LIMITACION ANTERIOR NO SEA APLICABLE EN EL CASO DE USTED. EL VENDEDOR NO SERA RESPONSABLE EN NINGUN CASO DE NINGUN DAÑO INCIDENTAL O EMERGENTE (INCLUYENDO PERO NO LIMITADO A RESPONSABILIDAD POR PERDIDA DE BENEFICIOS) QUE SE PRODUZCA COMO CONSECUENCIA DE LA VENTA O UTILIZACION DE ESTE PRODUCTO.
© Robert Bosch Tool Corporation 1800 W. Central Road Mt. Prospect, IL 60056-2230 Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056-2230, E.U.A. Importado en México por: Robert Bosch, S.A. de C.V., Calle Robert Bosch No. 405, Zona Industrial, Toluca, Edo. de México, C.P. 50070, Tel.
