be changed further in these riding modes, js NOTICE io di 4 BMW Motor rad recommends usA message is displayed ff ing the Max setting for off-road a setting is not possible the selecting riding mode operation and the Mix setting Counterexample riding for better ground accessibility.« mode: damping not adjusted.
Operation The selection arrow 4 appears on the display. » The selection row 4 disappears after the status is changed.
with Pro riding modes and installed encoding plug ~ DYNAMIC PRO: Dynamic riding on a dry road surface. — ENDURE PRO: Riding off-road with off-road treys with large tread block. When an encoding plug is installed, the DYNAMIC PRO and ENDURE PRO riding modes replace DYNAMIC and ENDURE. The interplay of throttle response, ABS control and ASC/ DTC control is optimized for each of the scenarios. ~ with Dynamic ES ACE The chassis and suspension adjustment can also be adjusted in the scenario selected.
Operation + Repeatedly press button 1 until the desired riding mode is dis Pro riding mode: bear in mind that ABS control is deactivated for the rear wheal « The following ride modes can be selected: — RAIN: For riding on a rain-wet road surface. ~ ROAD: For riding on a dry road surface. ~ with riding modes Pro The following riding modes are additionally available for selection: ~ DYNAMIC: For dynamic riding on a dry road surface.
= Reinstall the protective cap after removing the coding plug = Remove the cover cap from the plug connection press in latch 1 and remove the cap. « Install the encoding plug. = Switch on the ignition. The symbol for the encoding plug 1 is displayed. The riding modes ENDURE PRO and DYNAMIC PRO can be selected and replace the ENDURE { and DYNAMIC riding modes. + Installing front seat (x= 32).
Operation Display when adjusting [ 1 Adjustment range for settings (Speed Limit Info speed control ) 30..210 kmh “4% Telltale light for cruise control shows. # The motorcycle maintains your “55 current cruising speed and the = Slide switch 1 to the right. setting is saved, » Button 2 is enabled for operation. y alerting The symbol 1 for cruise control ga d speed : is displayed in the Pure Ride view ing roa and the top status line.
® Push button 1 forward and hold it in this position. » The motorcycle accelerates spotlessly. * The current speed is maintained and saved if button 1 is * The motorcycle decelerates sleeplessly. » The current speed is maintained and saved if button 1 is not pushed again. Deactivate cruise control not pushed again. « Brake, pull the clutch lever Decelerating or tum the throttle twist grip 2 (close the throttle by muting the twist grip back past the idle position) to deactivate the cruise-control system.
‘telltale light for cruise colon shows, Hill Start Control brake failure = It is essential to apply the brakes manually to hold the vehicle« Angel Switching off cruise control Lyle) Hill Start Control is purely a comfort system to facilitate holding i the machine and pulling way on uphill gradients and should The symbol 1 for drive-off assist not be confused with a parking ant is displayed in the Pure Ride brake« view and tha top status line.
he holding symbol is displayed. » Hill Start Control has been activated. « To switch off Hill Start Control, operate the parking brake lever 1 again. The holding symbol disap® Or drive off in first or second gear. [10+ Hill Start Control is deactivated ‘automatically when the motorcycle pulls away «4 general waning light + flashes yellow. ® he holding symbol flashes WEL) briefly. Once the brake has been fully released, the holding symbol disappears. » Hill Start Control has been switched off.
Operation » Anti-theft alumna is active. = Press button 1 again on the radio-operated key during the activation pasha to deactivate the motion sensor (8.9. to transport tha motorcycle by train when the severe movements may activate the alarm). » Tum indicators flash three times. » Confirmation tone sounds three times (if programmed). » Motion sensor has been deactivated.
If an alarm was triggered while the motorcycle wes unattended, the rider is notified accordingly by an lama tone sounding once when the ignition is switched on. The DWA LED then indicates the reason for the alarm for one minute.
Operation Possible settings Warning signal: Set rising and falling or intermittent alarm tone. Tilt sensor: Activate the tilt alarm sensor to monitor the inclination of tha vehicle. The anti-theft alarm goes off in the event of wheel theft or towing, for example. Deactivate the tilt sensor when transporting the vehicle to prevent the anti-theft alarm from bang triggered. 4 Arming tone Confirmation dam tone after having activated’ deactivated the DWA in addition to flashing indicators.
# Repeatedly press button 1 until the desired heating level 2 appears in front of the heated grip symbol 3. The hairband grips have two stage heating. ¥ss) 50% heating power 100% heating power v » Stage 2 is for heating the grips quickly: it is advisable to switch back to stage 1 as soon as the grips are warm. * The selected heating stage will be saved if you allow a certain length of time to pass without making further changes.
Front and rear seats Installing rear seat Removing rear seat Firmly press down rear seat 1 B © Canter the radar seat in rear # The rear seat engages with an © mounts 1 and engage it in audible click front mount 2. » Installing front seat 92) Tum ignition key 1 clockwise. ~~ ® Push the rear seat in the dire Push rear seat 2 in the forward Action opposite the forward direction of travel and lft it up direction of travel. . to remove =» Hack that the rear seat is cor= Place the refer seat, erectly seated.
Remove front seat + Tum ignition key 1 counterclockwise and hold it in this position, while slightly lifting front seat 2 at the rear. = Work front sat 2 to the rear to disengage it from seat holder 3 and remove. # Place the front seat, upholstered side down, on a clean surface. Adjusting the seat height and seat angle « Remove front seat remove the front height admen and align it with 1 (identification L).
« To adjust the low seat position, swing the rear height adjustment 1 into position 3 (identification L). = To adjust the low seat position, swing tha radar height adjustment 1 into position 2 {identification H), If the seat angle needs to be adjusted: « Position the front and rear height adjustment differently. Operation = Installing front seat 92). © Installing front seat Lo : + Engage front seat 1 in seat mounts 2 on left and right and rest it on the motorcycles.
5 V charger interface Using the 5 V charger Interface ~ with 5 V charger interface © Obstruction of the steering angle and risk of fire dua to improperly routed cables Driving safety is impaired @ Do not wind cables around the handlebars, and ensure that the handlebars can move freely. = When routing the cable, ensure that the cable does not cons into contact with hot components. «4 Component damage Damage to cable or component.
= Connect the USB connector 1 of the electrical device to the USB A socket 2 of the access line. = Connect the angle coupling 3 to the socket 4 of the 5 V charger interface.
TFT display General instructions Principle Pure Ride view. General settings Bluetooth ns My Vehicle Navigation Switch GPS synchronization on or off ET Display software version Display license information 103 . 105 106 110 L118 15 115 . 116 . 116 .
TET display General instructions Wakings the Journey or while the engine Is running Risk of accident = Always observe the relevant road traffic regulations. * Do not use the smartphone during the journey {apart from applications that do not require operation, 8.9. making telephone calls with the hands-free system).
systems, the BMW Motor rad Connected App must be opened before use. Actuality The TFT display may be updated after the publication date. Because of this, your motorcycle may differ from the information supplied in the Rider's Manual For up-to-date information go to Principle Controls All contents of the display are operated using the multi-controller 1 and the MENU 2 rocker button. Depending on the context, the following functions are possible.
Confirm selection. Confirm settings. — Advance a menu step. ~ Scroll to the right in lists. ~ In the My Vehicle menu: avarice one menu screen MENU rocker button functions Instructions given by the navigation system are displayed in a dialogue box if the Navigation menu has not been called up. Operation of the MENU rocker button is temporarily restricted 4 Briefly push MENU up: — In the View menu, change up a level. ~ In the Pure Ride view: change the display for rider info status line.
Operating instructions in Lea || sub menus In addition to the operating inroad st ructions in the main menu, 0, there are further operating ina st ructions in sub menus. on whether it is possible to go back to the top. — Operating instruction 2: another sub menu can be called up. Operating instruction 3: there ‘What the operating instructions mean: ~ Operating instruction 1: the left end has been reached.
TET display Switching functions on and off pr EES FL Some menu items have a check box in front of them. The check bax shows whether the function is on or off Action symbols after the menu items show what wil be switched by tilting the multi controller briefly to tha right. Examples for switching on and off: ~ Symbol 1 shows that the function is switched on. ~ Symbol 2 shows that the function is switched off. — Symbol 3 shows that the function can be switched off.
down until the desired entry is highlighted. # To move the cursor up in lists, tum the multi-controller 1 up until the desired entry is highlighted. Confirm selection. = Select the desired entry. « Briefly press the multi-controller 1 to the right. Call up the last menu used # In Pure Ride view: press and hold the MENU rocker button. * The last menu used is called up. The last entry highlighted is selected.
— System status 2: ABS function is switched off. Switch display for rider info status line Requirement The vehicle is at a standstill. The # Average consumption 2 Driving time 1 Driving time 2 F Pure Ride view is displayed. Inactive period 1 oo Switching on ignition (= 561 prong ang hold button 1 to 4» Althea information necessary gig jay the Pure Ride view. (7) elective period 2 = for ding on Public roses Briefly press button 1 to represented in the splay > fe by the on-board computer.
Select content of the rider info status line #Cathedral Unintelligent, Antigen, In halt Statuette menu = Switch on the desired displays. * It is possible to switch between the selected displays in the status line. If no displays are selected, only the range will be displayed. Adjust settings « Select and confirm the desired settings menu. # Tum the multi-controller 1 downwards until the desired setting is highlighted. = If theta ara operating instructions, tit the multi-controller 1 to the right.
Depending on the oil temperature, the red engine speed range changes: The colder the engine, the lower the engine speed at which the red engine speed range starts. The warmer the engine, the higher the engine sped at which the red engine speed range starts. Once the operating temperature has been reached, the red engine speed range display does not change any more. If the engine speed is too high, the entire scale flashes.
General settings Adjust the volume = Conn act rider's and passenger's helmet (+4 108). Increase volume: tum the multi-controller upwards. © Decrease volume: turn the multi-controller downwards. * Mute: tum the multi-controller all the way down. Setting the date = Switching on ignition (s»56). # Call up the Ein muskellunge SystemeinstellungenDatum und UhrzeitDatum einsteinium menu * Set the Tag, Mona and Jar.
Confirm setting. Set units of measurement o Call up the Ein— muskellunge, Systematization, Heighten menu The following units of measurement can be set: ~ Distance covered — Pressure ~ Temperature — Speed — Consumption Set language ¢ Cal up tha Ein muskellunge, Systematization, Preacher menu The following languages can be set: — Chinese ~ English — English Spanish — French Italian ~ Dutch ~ Portuguese = Russian = Ukrainian Adjusting brightness © Call up the Settings, Display, Brightness menu.
connections over short distances, as with every other windlass technology disruptions are possible. Interference can affect connections or connections can sometimes fail. Particularity when multiple devices operate in & Toothbrush network, with wireless technology of this nature it is not possible to ensure fault free communications in every situation Possible sources of interference: ~ interference zones due to transmission masts and similar.
Passenger helm. The connection status for mobile end devices is displayed. Connect mobiles end device « Pairing (us 107) ® Activate the mobile and device's Bluetooth function {see mobile end device's operating instructions). = Select Mobile device and confirm. +» Select CONN. NEW MOBILE DEVICE and confirm. Mobile end devices are being searched for. Tha Bluetooth symbol i fishes in the bottom status line during pairing Mobile end devices found are displayed = Select and confirm mobile end device.
» If the connection is not established, consult the troubleshooting chart in the section entitled "Technical data". {= 213) # If the Bluetooth connection is not working as expected, consult the troubleshooting chart in the section entities "Technical data". (w= 213) Delete connections ® Call up the Settings, Connections menu. # Select Delete connections. = To delete an individual connection, select the connection and confirm. = To delete all connections, select Delete all connections and confirm.
Vehicle Start screen 1 Hack control display Mode of presentation (= 25) Coolant temperature (=e 41) Range (us 104) Total distance traveled Service-due indicator (= 53) Rear Tyre pressure 43) On-board voltage (ss 186) Engine oil level (=e 40) Front Tyre pressure (= 43)
‘Operating instructions Scroll through menu ~ TRIP COMPUTER screens with Tyre pressure control (RDC)%E ~ TYRE PRESSURE<] — SERVICE REQUIRE MEETS = For moral information on Tyre pressure and check control messages, see the "Displays" section. Check control messages are at— Operating instruction 1: tabs which show how far to the sft = Call up the My Vehicle or right can be scrolled. menu.
Service requirements service is less than a month or if the next service is due within 700 miles (1000 km), a white CC message is displayed.
Navigation Warnings Using a smartphone during J tha en Risk of accident = Always observe the relevant road traffic regulations. « Do not use the smartphone during the journey (apart from applications that do not require operation, e.g. making telephone cal with the hands-free system).
Select destination from favorites © The FAVORITES menu displays all destinations which have been saved as favorites on the BMW Motor rad Connected App. No new favorites can be added to the TFT display. Call up tha Navigation, Favorites menu = Select and confirm destination. = Select Start guidance. Enter special destinations = Special destinations, such as points of interest, cen be displayed on the map. o Call up the Navigation, Poos menu.
= Select Current instruction and confirm The vehicle is connected to a compatible mobile end device and helmet. Control music playback # Call up the Media menu. # Adjust the volume {= 105). © Pause: press button 2 down. # Next track: briefly tilt multi-controller 1 to the right. = Last track or start of the current track: briefly tilt multi-controller 1 to the left. Fast forward: hold multi-controller 1 to the right.
Phone calls with multiple participants During one phone call, a second call can be accepted. The first phone call is put on hold. The number of active calls is shown in the Telephone menu. Iris possible to switch between two phone calls Telephone data Depending on the mobile end device, telephone data is transmitted to the vehicle automatically once pairing is complete (we 107).
Anticlimactic Mirrors Adjusting mirrors © Tum the mirror to the comet position. Adjusting mirror arm © Push protective cap 1 up over the threaded fastener on the mirror am. = Slacken nut 2 = Turn the mirror arm to the appropriate position. =» Tighten the nut ta tha transpacific tightening torque, while holding the mirror arm to ensure that it doss not move out ~N Mirror (lockout) to adapter 22 Nm (Le-hand thread) = Push the protective cap over the threaded fastener.
Adjusting headlight beam throw Hh If, for a high load, the adjustment of the spring per-load is no lager sufficient not to dazzle ‘oncoming traffic: + Tum adjuster knob 1 counterclockwise in order to lower the headlight beam again. When the motorcycle is again ridden with a lower load: = Have the basic settings of the headlight restored by a specialist workshop, bast of all by 8 BMW Motor rad dealer. ~ with LED headlight ®& 2 The headlight beam-throw is adjusted via an engage pivot lever.
Anticlimactic Clutch Adjusting the clutch lever Adjusting the clutch lever while riding Risk of accident = Do not attempt to adjust the clutch lever unless the motorcycle is at a standstill. = Tum knob 1 to tha desired position. NOTICE The adjuster is easier to tum if you push the clutch lever forward.
Shift mechanism Adjusting shift lever Adjusting foot brake lever + Marks sure the ground is level and firm and place the motorcycle on its stand. » Swing the footplate up until it Latches in position for riding in the seated position. Maladjustment ® Slacken screw 1. = Turn peg 2 to the desired pos# Unlatch footplate 1 of the footrest by pushing it to the left. If the peg is set too high or too low, there may be problems when changing gear. If there are shifting problems, check the position of the peg.
Anticlimactic | 8Nm Handlebars Adjustable handlebars The motor cycle handlebars can ba adjusted in their tilt within the ranges of marking 1. If you want to have the handlebars adjusted consult a specialist workshop, preferably an authorized BMW Motor rad dealer. ~~ Peg (clamp) to shift lever Spring reload Adjustment ~ without Dynamic ESAU It is essential to set the spring reload of the rear suspension to suit the load carried by the motorcycle.
Adjusting spring reload while riding. Risk of accident # Do not attempt to adjust spring reload unless the motorcycle is &t a standstill. «4 « If you want ta increase spring reload, tum knob 1 in the direction indicated by the HIGH mow. « If you want to reduce spring reload, tum knob 1 in the direction indicated by tha LOW mow. Basic setting of spring reload, rear — without Dynamic ES ACE Tum the knob as far as it will go in the LOW direction.
Anticlimactic « If you want to increase damping, tum adjusting screw 1 clockwise. = If you want to reduce damping, tum adjusting screw 1 counterclockwise. Basic setting of rear suspension damping characteristic Tum tha adjuster knob as far it will go in the clockwise direction, then back it off 8 clicks in the counter-clockwise direction.
Riding Safety instructions . 126 Comply with checklist 128 Always before riding off: .. 129 Every 3rd refueling stop 129 Starting 129 Running in 132 Off-reading .. cede. 133 Shifting gear . L134 Brakes . .. 135 Parking your motorcycle Ce. 137 Refueling... cede.
@ = 2 Safety instructions eider's equipment Do not ride without the correct clothing! Always wear. ~ Hematite ~ Motorcycling jacket and trousers — Gloves Boots This applies even to short journeys, and to every season of the year. Your authorized BMW Motor rad dealer will be glad to advise you on the correct clothing for Avery purpose.
= Pack heavy items at the bottom and toward the inboard side. « Note the maximum permissible payload and the speed limit for riding with cases fitted, as stated on the label inside the case (see also the section entitled "Accessories"). # Note the maximum permissible payload and the speed limit for riding with top case fitted, &s stated on the label inside the case (see also the section entitled "Accessories"). — with tank Tobago # Note the maximum permissible payload of the tank rucksack.
Riding isk of burn injury Risk of burn injury © When you park the vehicle make sure that no-one and no objects can coma into contact with the hot engine and exhaust system.« Catalytic converter If misfiring causes bummed fuel to enter tha catalytic converter, there is a danger of overheating and damage. The following guidelines must be observed: — Do not run the fuel tank dry. ~ Do not attempt to start or run the engine with a spark-plug cap disconnected — Stop the engine immediately if it misfires.
Always before riding off: # Check operation of the brake system. = Check operation of the lights and signaling equipment ® Checking clutch function [es 168). % Checking Tyre tread depth fo 170) = Checking Tyre pressure fan 169) # Check that cases and luggage ara securely held in place.
= Rags the starter button 1 {ale 3) The start attempt is automatically interrupted if battery voltage is too low. Recharge the battery before you start the engine, or use jump leads and a donor battery to start. See the subsection on jump starting in "Maintenance" for more details. « » The engine starts. » If the engine refuses to start, consult the troubleshooting chart in the section entities "Technical data".
Phase 1 » Test of the diagnose system components with the vehicle at a standstill ABS telltale and waning Le light flashes. Phase 2 » Test of the wheel-speed sensors 8s the vehicle pulls way from rest. #555 ABS telltale and warming 54. light flashes. ABS self-diagnosis completed » The ABS indicator and warning light goes out = Check all the indicator and waning lights. After the ABS self-diagnosis completes, an indicator showing an ABS fault will appear. # You can continue to ride.
DTC self-diagnosis ~ with riding modes Pro BMW Motor rad DTC performs doff-diagnosis to ensure its penetrability. Self-diagnosis is performed automatically when you switch on the ignition. om = # Phase 1 2 » Test of the diagnosis-compatible system components with the vehicle at a standstill a] DTC indicator and waning £3. light fishes slowly. Phase 2 » Pull away test of the system components with diagnostic capability. #343 DTC indicator and waning By light fishes slowly.
= Note the mileage after which the running-in check should be carried out. Mileage until the running-in check km Brake pads New brake pads have to bed down before they can achieve their optimum friction levels. You can compensate for this initial reduction in braking efficiency by exerting greater pressure on the ravels. Now brake pads Longer stopping distance, risk of accident = Apply the brakes in good time. « Tyre New treys have a smooth surface.
Riding Increased brake pad wear = Heck the thickness of the brake pads more frequently and replace the brake pads in good time.« Spring reload and unshockable settings Changed values for spring reload and spring shut damping for off-reading Impaired driving characteristics on paved roads = Before leaving the off-road terrain, set the correct spring reload and shock absorption 4 Rims BMW Motor rad recommends checking the rims for damage after off-reading.
# You select the gear in the usual way by means of the foot-operated shift lever. » Sensor 1 on the selector shaft registers the shift request and triggers shift assistance. * When riding at a steady speed in a low gear at high engine pm, an attempt to shift gear without puling the clutch can cause a severe load-change reaction. BMW Motor rad recommends disengaging the clutch for shifts in these circumstances.
Riding Hazard braking with ABS Pro©E If you brake sharply from a speed in excess of 50 km, the brake light flashes rapidly as an additional waning for road users behind you. The hazard waning lights system switches on if you brake to below 15 kmh in this process. The hazard waning lights system automatically switches off again from a speed of 20 km/h.
Possibility of a fall not precluded Although ABS Pro provides the rider with valuable assistance and constitutes a huge advance in safety for braking with the motorcycle banked for cornering, it cannot under any circumstances be considered es redefining the physical limits that apply to motorcycling. It is still possible for these limits to ba overshot dus to misjudgment or rider error.
Always check that the ground under the stand is level and dim« Center stand folds In due to sharp movements Risk of damage to parts if vehicle topples = Do not lean or sit on the vehicle with the center stand extended 4 = Extend the center stand and lift the motorcycle onto the stand. = On a gradient, the motorcycle should always face uphill; select 1st gear. Refueling Fuel grade Requirement For optimum fuel consumption, fuel should be sulfur-free or as low-sulfur as possible.
Escape of fuel due to heat induced expansion if fus! tank Is overfilled Risk of falling ® Do not overfill the fuel tank « Wetting of plastic surfaces by ful » Open the protective cap 2. » Use ignition key 1 to unlock fuel filler cap by muting it clockwise, and flip the cap Damage to the surfaces (surfaces become unsightly or dull) open. + Clean plastic surfaces immediately after contact with fuel« = Marks sure the ground is level and firm and place the motorcycle on its center stand.
@ = 2 quantity that the fuse tank could hold if refilled after it had been run dry and the engine had cut out due to a lack of fuel.« 7 Usable fuel capacity [approx 201 Tl Reserve fuel approx. 4 | « Press the fuel tank cap down firmly to colas. = Remove the key and close the protective cap. Refueling — with Key less Ride ©E Requirement The steering lock is disengaged. Fuel is highly flammable Risk of fire and explosion © Do not smoke.
Version 1 ~ with Key less Ride Requirement Within the waiting time # Pull up tab 1 of the fuel filler cap slowly. » Fuel filler cap unlocks. # Fully open the fuel filler cap. Version 2 ~ with Key less Ride %& Requirement After the waiting time has expired = Bring the radio-operated key into range. Slowly pull tab 1 up. » The tali tale light for the cooperated key flashes while the search for the radio-operated key is in progress. « Again slowly pull up tab 1 of the fuel filler cap.
Reserve fuel all approx. Press down firmly on the filler cap of the fuel tank. » The fuel filer cap engages with an audible click. » The fuel filler cap locks automatically when the waiting time expires. » The engaged dual flair cap locks immediately when you secure tha steering lack or switch on the ignition. Securing motorcycle for transportation = Make sure that all components that may come into contact with pensioning straps ara adequately protracted against scratching.
# Secure the pensioning straps at the refer on both sides ta the frame for the rear footrest and tighten tha straps. « Tighten all the straps uniformity; the vehicle's suspension should be compressed as tightly as possible front and rear.