Installation Guide

ManualsBrandsRobern ManualsLightingRobern Eyezon Single Light 16" Bathroom Bath Bar with White Shade and Night Light

This instruction sheet contains information

on how to install EYEZON™ TOPLIGHT

FOR M and PL SERIES cabinets.

The lights are designed to attach to Robern

M and PL Cabinets. For information on

installing cabinets and lighting, see the M or

PL Series instructions that are shipped with

the cabinets.

Save these instructions for future use and

reference. An improper installation voids

the warranty. Installed products cannot be

returned.

If you experience any problems with your

cabinet, contact your dealer or Robern

directly.

Limited Warranty — One Year Term

Ce feuillet d’instruction contient

l’information sur comment installer les

Eyezon ™ TOPLIGHT pour modules de la

série M-PL.

Les lampes sont conçues pour se xer

aux armoires M et PL de Robern. Pour

l’information sur l’installation des armoires

et de l’éclairage, voir les instructions pour les

Séries M ou PL qui sont expédiées avec les

armoires.

Conservez ces instructions pour référence et

utilisation future. Une mauvaise installation

annule la garantie. Des produits installés ne

peuvent pas être retournés.

Si vous éprouvez de la difculté avec votre

armoire, veuillez contacter soit votre march-

and ou contactez directement Robern.

Garantie limitée — d’une durée d’un an

Esta hoja de instrucciones contiene

información sobre cómo instalar las Eyezon

™ Toplight para armarios de la serie M-PL.

Las luces están diseñadas para ser colocadas

en gabinetes M y PL de Robern. Para

obtener información sobre la instalación

de los gabinetes y las luces, consulte las

instrucciones de la Serie M o PL que se

envían con los gabinetes.

Guarde estas instrucciones para uso y

referencia futura. La instalación inadecuada

invalida la garantía. Los productos instala-

dos no podrán devolverse.

Si usted tiene algún problema con su gabi-

nete, póngase en contacto con su distribuidor

o directamente con Robern.

Garantía Limitada – Término de Un Año

EYEZON

™ TOPLIGHT

for M and PL Series Cabinets

M et PL Série Armoires

para M y PL Series Cabinets

nightlight and non-nightlight models

modèles veilleuse et non veilleuse

Robern, Inc.

701 N. Wilson Ave.

Bristol, PA 19007 U.S.A.

1.800.877.2376

INSTALLATION / INSTALLATION / INSTALACIÓN

⅝

”

92mm

60mm

”

83mm

16”/ 20”/ 24”

406mm / 508mm / 610mm

MPL24

MPL20

MPL16

Summary of content (12 pages)

PAGE 1
EYEZON™ TOPLIGHT for M and PL Series Cabinets M et PL Série Armoires para M y PL Series Cabinets nightlight and non-nightlight models modèles veilleuse et non veilleuse MPL24 MPL20 MPL16 3 1 4” 83mm 3 60mm 16”/ 20”/ 24” 406mm / 508mm / 610mm 3 ⅝” 92mm INSTALLATION / INSTALLATION / INSTALACIÓN This instruction sheet contains information on how to install EYEZON™ TOPLIGHT FOR M and PL SERIES cabinets. The lights are designed to attach to Robern M and PL Cabinets.
PAGE 2
1-1 PARTS / PIÈCES / PARTES HARDWARE BAG SAC DE QUINCAILLERIE BOLSA DE ACCESORIOS 216-1075 3-Pan Head type B Leader Point Screw #6-20 x 1 ¼ 3-Pan Head Type B chef de point vis # 6-20 x 1 ¼ 3-Tornillo #6-20 x 1 ¼, Cabeza troncocónica, Punta tipo B [203-1236] Light Fixture Luminaire artefacto de iluminación 2 18/8 SS Washer 2-Standoff, #6 x ½” x 0.250 Dia 4 Wire Connectors 2 18/8 SS Rondelle 2 Standoff, n ° 6 x ½ "x 0,250 Dia 4 Connecteurs de fils 2 18/8 SS Arandela 2-Standoff, # 6 x ½ "x 0.
PAGE 3
NOTES / REMARQUES / NOTAS Unpack the light. Check the box thoroughly for all hardware and loose parts. The EYEZON™ TOPLIGHT uses 24W or 36W 2G11 base twin tube fluorescent lamps. See page 2 for recommended replacement bulbs. DANGER: Risk of personal injury. To avoid possible electrical shock, the electricity must be turned off at the circuit breaker or fuse box before attempting any installation procedure. DANGER: Risk of personal injury.
PAGE 4
PREPARATION / PRÉPARATION / PREPARACIÓN 1. Remove lens by squeezing inward and pulling out. 1. Enlever la lentille en la pressant vers l’intérieur et en la tirant. 1. Quite el lente apretándolo hacia adentro y halándolo. 2. Remove reflector by removing screws on top and pulling reflector straight out. Note: A star tooth lock washer is located on one of the screws. 2. Enlever le réflecteur en ôtant les vis du dessus et en retirant le réflecteur directement.
PAGE 5
EYEZON™ ATTACHMENT EYEZON™ FIXATION EYEZON™ ADJUNTO IMPORTANT: For Recess installation of the EYEZON™, the light fixture should be installed on the cabinet before installing in wall. For Surface mounted installation, the EYEZON™ toplight should be mounted after the cabinet is installed on the wall. 4. Loosen screws as required but do not remove screws. The EYEZON™ should then be lowered over the screws until the bottom of the light fixture sits on top of the cabinet flange, (See below). 5.
PAGE 6
SURFACE MOUNTING / MONTAGE EN SURFACE / MONTAJE EN SUPERFICIE When installing the fixture on a wall, the height of the cabinet is higher by 3 5/8” (92mm). See the chart on page 7 for the overall height of the cabinets. First, install the cabinet on the wall as shown in Figure 1. 1. Be sure the field wire has been installed as shown in Figure 1. See the Electrical Connections Page 9 & 10 for the field wiring for the night light versus non night light models. Mount light fixture as shown on page 5.
PAGE 7
RECESS MOUNTING / MONTAGE ENCASTRÉ / MONTAJE EMPOTRADO When installing the fixture in a wall, the height of the wall opening is higher by 3 5/8” (92mm). See the chart below for the overall wall opening height for the three R3 cabinets. First, create the framed wall opening as shown below. The width of the opening is shown in the cabinet instructions. Be sure the field wire has been installed as shown in Figure 1.
PAGE 8
ELECTRICAL CONNECTIONS / RACCORDS ÉLECTRIQUES / CONEXIONES ELÉCTRICAS DANGER: To reduce the risk of electrical shock, shut off power before wiring the lights. DANGER: Pour réduire le risque de choc électrique, coupez le courant avant d’effectuer le câblage des lampes. PELIGRO: Para reducir el riesgo de electrocución, apague la electricidad antes de cablear el gabinete.
PAGE 9
ELECTRICAL CONNECTIONS / RACCORDS ÉLECTRIQUES / CONEXIONES ELÉCTRICAS Prepare your wire connection. Wiring connections are made through the front of the light fixture. Préparez votre connexion filaire. Les raccordements sont effectués par l’avant de l’appareil d’éclairage. Prepare la conexión de cables. Conexiones de cableado se realizan a través de la parte delantera de la lámpara. The light fixture wiring is routed into the plastic Romex connectors on the rear of the fixture.
PAGE 10
ELECTRICAL CONNECTIONS / RACCORDS ÉLECTRIQUES / CONEXIONES ELÉCTRICAS WITHOUT NIGHT LIGHT MODELS FIELD CONNECTION LIGHT FIXTURE COMPACT FLUORESCENT BULB: 2G11 BASE TWIN-TUBE 24 WATT (16" FIXTURE) -or32 WATT (20" & 24" FIXTURE) WALL SWITCH CIRCUIT BREAKER PANEL BLACK (L) NEUTRAL WHITE (N) GROUND GREEN (GND) BLUE OUT LINE INPUT 120VAC 15A CIRCUIT BALLAST RED CHASSIS GROUND NIGHT LIGHT MODELS LIGHT FIXTURE FIELD CONNECTION COMPACT FLUORESCENT BULB: 2G11 BASE TWIN-TUBE 24 WATT (16" FIXTURE) -o
PAGE 11
FINAL ASSEMBLY / ASSEMBLAGE FINAL / ENSAMBLADO FINAL 1. Replace reflector by installing screws on top. Note: A star tooth lock washer is located on one of the screws. 1. Remplacer le réflecteur en installant les vis du dessus. Remarque: une rondelle de blocage est située sur certaines des vis. 2. Reinstall bulb. Align four socket pins of the bulb with the slots in the lamp holder. Align bulb with the bulb clip. Carefully push bulb inward until fully seated. 2. Réinstaller ampoule.
PAGE 12
WARRANTY / GARANTIE / GARANTÍA 1-1 Limited Warranty One Year Term Garantie limitée d’une durée d’un an Garantía Limitada Término de Un Año ROBERN warrants to the original purchaser that, it will, at its election repair, replace, or make appropriate adjustment to products made by this company shown to have significant defects in material or workmanship which are reported to ROBERN in writing within one (1) year from the date of delivery. ROBERN is not responsible for installation costs.