User manual Multi Electric Stand electrical height-adjustable stand
Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 03.12.
Table of contents Table of contents 1 General information.............................................................................................................. 1.1 Further information........................................................................................................ 1.2 Notational conventions................................................................................................. 1.3 Symbols and signal words..............................................................
Multi Electric Stand electrical height-adjustable stand
General information 1 General information This user manual contains important information on the safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future refer‐ ence. Make sure that it is available to all persons using this device. If you sell the device to another user, be sure that they also receive this manual. Our products and user manuals are subject to a process of continuous development.
General information Instructions The individual steps of an instruction are numbered consecutively. The result of a step is indented and highlighted by an arrow. Example: 1. Switch on the device. 2. Press [Auto]. ð Automatic operation is started. 3. Switch off the device. 1.3 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this manual.
Safety instructions 2 Safety instructions Intended use This device is intended for use as multifunctional base for stable fixing and heightadjustable installation of keyboards, synthesizers, stage pianos, etc. and is not suit‐ able for lifting persons. Use the device only as described in this user manual. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage.
Features 3 Features Special characteristics: n Electrical height-adjustable stand for keyboards, synthesizers, stage pianos, mixers, studio equipment, etc.
Assembly 4 Assembly When assembling the stand, use felt-pad floor protectors or a carpet in order not to damage the coating of your parquet, linoleum, laminate or PVC floor. Open the package and make sure before assembling that the entire scope of delivery is present, as posted here.
Assembly % ö # $ 3. First attach the control panel (1) to the control panel holder (2). Use the four supplied slide screws (3) and the four round nuts (4) and hand-tighten them. ( ' & 5 4. 10 Multi Electric Stand electrical height-adjustable stand Place the tubes (6) and standing columns (7) as illustrated. Attach the mounted control panel holder with two Allen screws M6×25 (5) to the tube (6) and to the standing column (7) using the Allen key (20).
Assembly ) * 5. Attach the motor holder (8) with four Allen screws M6×10 (9) to both tubes (6) using the Allen key (20). + 6. Attach two adhesive cable ties (10) in the illustrated position to properly install the cable of the control panel.
Assembly , - .7. Slide the motor (11) in the holder (8) and connect the cables of the standing columns (12) and the cable of the control panel (13) to the motor. * / 8. 12 Multi Electric Stand electrical height-adjustable stand Attach the feet (14) with four Allen screws M6×10 each (9) to the standing col‐ umns (7).
Assembly + 0 9. Attach two adhesive cable ties (10) in the illustrated position to properly install the power cable (15). Connect the power cable (15) to the motor (11). Ensure that the power cable is not installed too tight in the cable ties. The cable should be able to move while adjusting the height.
Assembly 1 2 1 3 S 4 2 10. Turn the stand over and put it onto the feet. Attach the crossbars (16) at the desired position to both tubes (6) with two Allen screws M6×40 each (17) using the Allen key (20). 3 2 1 3 11. 14 Multi Electric Stand electrical height-adjustable stand S 4 Attach two adhesive foam pads (18) to each crossbar (16) at the desired posi‐ tions.
Assembly 4 * 2 1 3 S 4 % 12. Attach the angle pieces (19) if desired with one Allen screw M6×10 each (9) to the crossbars (16). Alternatively, you can attach the devices to be mounted on the stand with a 3/8” cylinder head screw each (not included in the scope of delivery) using the Allen key (20). Align the control panel (1) as desired and tighten the slide screws (3) and the round nuts (4).
Assembly 2 1 13. S 4 3 Align the adjustable feet to compensate for the floor unevenness.
Operating elements 5 Operating elements Control panel ö # $ % 1 Display 2 [1] | [2] | [3] | [4] Number buttons for storing and selecting a set height 3 [S] Buttons for storing a set height 4 | Buttons for setting the height Multi Electric Stand electrical height-adjustable stand 17
Operating 6 Operating Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively. Switching the unit centimeter/inch Press and hold [S] and [3] simultaneously until the unit display switches.
Technical specifications 7 Technical specifications Adjustable height, min. 61 cm (24 in) Adjustable height, max.
EU Declaration of Conformity 8 EU Declaration of Conformity Name and address of manufacturer / EU-AR Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany THIS DECLARATION OF CONFORMITY IS ISSUED UNDER THE SOLE RESPONSIBILITY OF: Name and address of manufacturer Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Product identification 491963 Roadworx Multi Electric Stand THE PRODUCTS MENTIONED IN THIS DECLARATION ARE IN CONFORMITY WITH: EU Community Legislation Machinery Directive 2
EU Declaration of Conformity SIGNED FOR AND ON BEHALF OF: Place and date of issue Burgebrach, 29 November 2021 Multi Electric Stand electrical height-adjustable stand 21
Protecting the environment 9 Protecting the environment Disposal of the packaging material For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.