User Manual
If you find some inconsistency in this manual during use, please consult the technical support department. The content will be updated over time to time without notice. In order to ensure the normal operation of the device, to extend its service life, please ensure that it meets the specifications during installation. The device should be installed horizontally, as far as possible from locations with high vibrations.
Menu ................................................................................................................. 2 .........................................................................................................2 1. Product Introduction ..........................................................................................................5 1.1. Product description .............................................................................................................................
8.5. Install 4G&WiFi&GPS Antenna ........................................................................................................ 24 9. Use of Web App Configuration Tools ............................................................................. 25 9.1. Login ................................................................................................................................................. 25 9.2. Status inquiry .......................................................................
1. PRODUCT INTRODUCTION 1.1. PRODUCT DESCRIPTION The product is a active safety intelligent prevention and control system.Supporting the following functions: Driver monitoring system(DMS), forward collision warning (ADAS), blind spot detection(BSD), support for GPS/BD positioning, 4G network communication, multi-channel video surveillance，local dual SD card storage, etc. The product is designed to improve the driving safety of the driver.
2.4. PROFESSIONAL AND RELIABLE ACTIVE SAFETY Support DMS, ADAS, BSD and other AI algorithms Deep learning technology: accurate target recognition and fast iterative update Support the latest neural networks of the industry 2.5.
3. APPEARANCE DESCRIPTION 3.1. FRONT VIEW Figure 1：Front view of the controller box 3.1.
3.2. SYSTEM CONNECTION DIAGRAM Figure 3 Note: The solution is flexible and can be customized according to customer needs. 4. PRODUCT CONFIGURATION LIST 4.1.
4.2.
4.3. DEVICE HARNESS Sub I/O GPS 、 WIFI 、 4G antenna I/O Speaker Power ADAS camera Rear view/LBSD/FBSD camera DMS camera RBSD camera IPC camera or network interface CVBS Figure 4: Device Cable Connection The harness has a variety of function combinations.
5. PRODUCT FUNCTION OVERVIEW Function type Function description Voice prompts Satellite positioning, etc.
Camera Cover Warning If the blocking object covers the driver's status monitoring camera for more than the set time, the device will send out a blocking alarm "Do not camera" block the Blind zone detection auxiliary system Blind Spot Detection BSD: Blind Spot Detection When the vehicle is driving and detects the presence of pedestrians, vehicles and other obstacles on the blind area, the device will issue a warning, "Please note the pedestrian on the right" Rapid acceleration, Rapid deceleration, S
6. INSTALLATION PREPARATION 6.1. SITE TERRAIN REQUIREMENTS Find an open area before installation. In principle, it is required to install and calibrate in areas with flat road, wide vision (skyline can be seen) and lane lines. Considering the actual situation, the installation and calibration shall be carried out at least on the flat ground. Park the vehicle horizontally. It is forbidden to install and calibrate the device when the vehicle is in an inclined state.
Whether the vehicle power supply system is in good condition, whether there are other electrical faults, etc. Whether the vehicle has appearance damage. 6.4. DEVICE INFORMATION CONFIRMATION 6.4.1. Hardware information confirmation Before installation, check whether the device is complete and damaged. The specific device list shall be subjected to the project plan. 6.4.2.
7.
8 Insulating black tape Used for binding thread 9 tie-wraps 7cm long, used to fix the harness 10 Adhesive tape It is used to fix the DMS bracket when the hole cannot be punched 11 Electric screwdriver Professional Electric screwdriver, with a drill diameter of 3cm, is used to fix screws and make holes when walking dark lines 8. INSTALLATION GUIDANCE AND PRECAUTIONS 8.1. INSTALL THE CONTROLLER 8.1.1.
Device’s GND connects to vehicle GND position If the description of the fuse box is vague and cannot be judged, the corresponding harness can be found by measuring with a test pencil. The judgment method is as follows： Vehicle Power Harness(VIN) ：When the vehicle engine turning off, use the test pencil to measure whether the VIN has electricity. If there is electricity, you can judge that this harness is VIN, and then measure the voltage to ensure that it is within the scope of use of the device.
20° MAX Figure 5: Installation Position 2)Anti-vibration: the device shall be installed at the place with weak vibration of the vehicle and away from the engine; If you choose to install it on the center console of the vehicle, ensure that the device is firmly installed and that the device will not move due to vehicle shaking during vehicle driving.
SD CARD1 SD CARD2 SIM CARD figure 6： Installation of SIM and SD Card 8.2. INSTALL DMS CAMERA 8.2.1. Installation position requirements The DMS camera is installed on the dashboard in front of the driver, within 60cm~120cm from the driver's face, and the included angle with the normal of the face when the driver looks forward is required to be less than ± 30 °; The included angle with the face normal in the vertical direction is less than 30 °, as shown in Figure 7 below.
camera angle through the universal ball shaft until the driver's face is in the center of the display and occupies about 1/3 of the screen, as shown in Figure 9 below. Figure 8：DMS Camera fixing 8.2.3. Precautions Figure 9：Driver position of DMS Camera Since the camera is installed above the center console, it is necessary to ensure that the installation will not affect the driver's driving vision.
8.3. INSTALL ADAS CAMERA 8.3.1. Installation Position Requirements The middle of the windshield is recommended. Commercial vehicles are relatively high, so the camera is located below the middle of the windshield; The passenger car is low, and the camera is installed above the middle of the windshield, as shown in Figure 10 below. Middle line middle line Figure 10：ADAS Camera Installation Position 8.3.2.
Figure 12：Adjust the angle Figure 13：Make sure the skyline is in the center of the screen or in web-app 8.3.3. Wiring and precautions When wiring, pay attention to put the harness into the gap between the windshield and the center console as far as possible to hide the harness; Before fixing the camera, check whether the camera is clean. If there are fingerprints or dirt, please gently wipe it with a soft cleaning cloth.
Figure 14: BSD installation 8.4.2. Camera Installation and Angle Adjustment Measure the height of the BSD installation position with a tape measure, mark it, and wipe the vehicle of the installation position with alcohol to remove dust. Fix the bottom of the protective support of BSD camera to the vehicle body through screw punching, or contact the customer's welder to assist in welding and fixing.
heat dissipation pipe Harness routing Figure 16: Wiring requirements 8.5. INSTALL 4G&WIFI&GPS ANTENNA 8.5.1. install 4G & WiFi antenna When installing 4g & WiFi antennas, do not pile them up disorderly. When the antenna length is long, it can be folded and tied When installing and fixing, it should be placed vertically. Tear off the 3M adhesive protective sticker at the back and stick it in a suitable position: the pillar of the vehicle (recommended) is shown in Figure 27 below.
8.5.2. Install GPS Antenna The installation position of GPS antenna is preferentially selected on the roof, and the harness can enter the vehicle through punching or along the door gap. If it cannot be installed on the roof, it is recommended to install it on the console in front of the passenger seat, as close to the window as possible.
9.1.2. Login Web App Open the mobile browser, enter "192.168.1.1" in the website bar, and click go to enter the login page; After checking the device number and the actual device number, enter the password: 123456, click login, and enter the homepage of the web app 9.2. STATUS INQUIRY Click "status inquiry" to enter the status inquiry page.
9.3. SETTING 9.3.1. Set Vehicle Information： Click “setting---general---vehicle info”，input “the license plate color,license plate number”，etc，The business line number can be filled in by clicking the "+" on the right to select "HuoYun" or "default" (it is recommended to select "HuoYun") or according to the demand. 9.3.2. Set IO Status： Click “setting---General---IO signal”，According to the actual situation, set the trigger level “high” or “low” value to be effective 9.3.3.
9.3.4. Set ”display linkage” and “mirror and flip” According to the actual project requirements, click "setting - VIDEO - display linkage" or "setting - VIDEO mirror and flip".You can set the “display linkage” function or mirror / flip the video of any channel 9.4. ALGORITHM SETTING 9.4.1.
If there are obstacles in front of the vehicle, and the lane line and the distant skyline cannot be seen, the installer can also use the calibration rod to calibrate. Step 1: prepare a calibration rod whose length exceeds the installation height of the camera and stand it 1.
9.5. LIVE IMAGE click "live image" to enter the real-time image page to view the images of each channel. After selecting "refresh preview image automatically", you can select one channel to view the real-time video of that channel.
9.6.
9.7.
10. USER NOTICE 1. The product is a active safety intelligent prevention and control system, which can help enterprises manage fleets and monitor the status of vehicles in real time. 2. The driver using this product can reduce the possibility of traffic accidents caused by manual driving, but it cannot replace safe driving. The driver must still be attentive at all times and obey traffic regulations for safe driving. 3.
FCC warning statements: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
