Quick Operation Manual

ManualsBrandsRL ManualsElectronicsNVR WIFI

One

NVR WIFI

Quick operation manual

Version 1.0

This manual covers only basic operations.

This manual,to adapt to different types,each specific operation can not be listed one by one,the final

interpretation rights belong to the company.

Hardware description

1．statement

Thank you very much for purchasing our products. If you have any questions or need,please feel free to

This manual is applicable to network wireless NVR.

This manual may contain technical inaccuracies,inconsistencies with product functions and operations,or

typographical errors

The company will update the contents of this manual according to the enhancement of product functions,and

will regularly improve or update the products or procedures described in this manual. The updated contents will

be added in the new version of this manual without notice.

If the description of the product in the manual is inconsistent with the real product,the real product shall

prevail

2．safety precautions

1.Do not expose the wireless NVR to damp,dusty conditions；

2.Wireless NVR should be placed in a well-ventilated place. Do not block the vents of this product；

3.Wireless NVR should be placed in a well-ventilated place. Do not block the vents of this product；

4.Wireless NVR should work within the temperature and humidity allowed by technical specifications；

5.The wireless NVR is placed horizontally and avoids being installed in the environment of violent vibration；

6.The dust on the circuit board will cause a short circuit after being affected by moisture. In order to make the

wireless NVR work normally for a long time,the brush can be regularly used to remove dust on the circuit

board,connectors and chassis；

7.Improper battery replacement may cause explosion hazard. It is not recommended for users to replace the

battery by themselves. In case of replacement,only use the same type or equivalent type of battery to replace,do

not try to open or repair the battery；

8.Please select the hard disk recommended by the manufacturer,suitable for wireless NVR work

requirements,to meet the requirements of long time,large amount of data reading and writing,and at the same

Summary of content (14 pages)

PAGE 1
NVR WIFI Quick operation manual Version 1.0 This manual covers only basic operations. This manual,to adapt to different types,each specific operation can not be listed one by one,the final interpretation rights belong to the company. Hardware description 1．statement Thank you very much for purchasing our products. If you have any questions or need,please feel free to contact us. This manual is applicable to network wireless NVR.
PAGE 2
time,please buy from the official channels,to ensure the quality of the hard disk； 9.When connecting all kinds of communication cables,please pay attention to lightning protection. It is forbidden to directly connect Ethernet cables introduced from outdoor to wireless NVR. 3．out of box audit After receiving the products,please open the packaging box,take out the equipment and place it in an appropriate place,and confirm the products and accessories according to the packing list in the box.
PAGE 3
5．Wireless IPC placement Wireless signal coverage of space like an apple,antenna located in apple,surrounding the signal is strong,the antenna dents two endpoints antenna,the signal is weak. According to the antenna divergence characteristics of signal,in order to ensure that the wireless set graphics,wireless antenna of IPC should try to keep each other with wireless form NVR antenna signal spherical parallel or tangent,as shown in the above.
PAGE 4
Figure 1-1 appearance diagram and interface diagram of wireless IPC serial designation describe Triaxial adjusting bracket Support triaxial adjustment number 1 installation 2 antenna Wireless signal transmitting/receiving antenna 3 rear cover Casing back cover 4 protegulum front cover 5 Double loop glass Prevent light leakage inside the lens 6 power port DC12V Power 7 Matching buttons NVR pairing button 8 antenna interface Antenna mount 6.2 installation procedure 1.
PAGE 5
Figure 2-2 fixed wireless IPC 3.Triaxial adjustment of support: release the locking screw of wireless IPC support,then triaxial adjustment can be carried out It is connected with the base through an axis to achieve 0-360 degree adjustment in the horizontal direction (P direction). Adjust the bracket The ball shaft can be adjusted 0-90 degrees in the vertical direction (T direction) and 0-360 degrees in the rotation direction (R direction).
PAGE 6
7．Interface description of back panel ② 1 1 antenna interface 2 VGA video output interface 3 HDMI video output interface 4 network port 5 Standard USB interface X 2 6 DC 12Vmains input 7 Ground wire interface ③ ④ ⑤ ⑥ ⑦ 8．Turn on/off Confirm that the incoming dc voltage matches the requirements of wireless NVR,and ensure that the middle earthing end of the wireless NVR POWER socket is well grounded.
PAGE 7
size 165（L）*66（W）*66（H）（Not including antenna） net weight About 350g Wireless NVR 4 road parameters main HTH embedded microcontroller processor operating Embedded Linux operating system system image system 1/4frames display Playback 1080P quality Video 4 OUTPUT 1080PAccess to the storage access motion Support detection Video Timing, manual, dynamic detection, external alarm mode local AV(audi o/video) Support 4 channel 1080P simultaneous playback playback Video Time point retrieval, c
PAGE 8
software operation 1．log in After normal startup of the device, log in is required before operation, and the system provides corresponding functions according to the log-in user rights. When the device leaves the factory, it is preset with 2 users admin and guest, with no password by default. Password protection: if the password is wrong for 6 times in a row, the alarm will prompt you to lock the account (after system restart or half an hour, the locked account will be automatically unlocked).
PAGE 9
4. remote upgrade Remote channel, the eighth item and the last item, remote upgrade. Click and select the ipc file to be upgraded in the upgrade interface. 5. Replay Theater Ways to open video playback: first, click the right mouse button on the preview interface to pop up a menu, and select [video playback] in the menu; The second type: [main menu] [recording function] [video playback].
PAGE 10
6.network settings Through [main menu] [system Settings] [network Settings], the local network Settings. 7.Motion Detection settings Motion Detection settings It is divided into two parts： How to set the alarm function of mobile detection (enable switch, sensitivity, detection area, time interval and disarming time), that is, how to set it to generate alarm.
PAGE 11
drawing—A remote control 1. WEB remote access After the network is connected, log in the NVR device to conduct remote monitoring by using the browser that comes with the PC. For the specific operation, please refer to the instructions of the WEB client. WEB interface 2. CMS3.
PAGE 12
3．mobile surveillance Mobile monitoring function is enabled by default. Enter the system Settings -> network service -> cloud service, check server address, port and UID, and download IOS and android system APP by scanning qr code. Mobile monitoring software :RView(new cloud server)/ Freecampro (old cloud server), mobile monitoring port is 5800/34600, respectively. APP method of application：（1 ）Login: there are two ways to login: login and local login. You need to register your account first.
PAGE 13
（4）Remote playback: enter the real-time preview menu, click the "+" button in the middle, and select the channel, start time and end time to play back the device, which can only play back 4 channels at most Thank you for your reading.
PAGE 14
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.