User's Manual

RL-9830G4
Screw pack
*2
NOTE: The above will clear the
code for all paired transmitters.
ON
OFF
User manual
*1
ON
OFF
1
2
Version1.0
PIR ALARM KIT
Package Contents
PIR alarm
(Main unit)
*2
Remote key fob
(Transmitter)
*2
Bracket
*2
PIR sensing area
PIR alarm (Main unit)
Indicator light
Code button
Alarm indicator: When the main unit sounds an alarm,
the light will flash quickly along with the alarm sound.
Low battery indicator: When the batteries installed
in the main unit reach a low level, i.e., less than 3.3V,
the light will flash slowly (time interval of 3 seconds).
Please replace batteries immediately when the low
battery indicator light flashes.
Remote key fob (Transmitter)
Arm button
Disarm button
Front view
Side view
HOME mode
AWAY mode
5. Press the Code button
again for 3 seconds by
inserting the screwdriver.
Two "Beep" tones will
be heard.
6. Release the screwdriver,
pairing is now completed.
Clearing Code
Door/window
magnetic sensor
(Transmitter)
*4
Magnetic contact
Indicator
light
BATTERY
-
+
BATTERY
-
+
BATTERY
-
+
Speaker
Once paired to the main unit and in
the ARM mode if the magnetic
contact is separated from the
door/window sensor the alarm will
sound. To disarm the alarm press the
OFF button on the remote key fob.
Door/window magnetic sensor
(Transmitter)
The PIR alarm A or B
Press and hold the Code button by
inserting the screwdriver (as above)
before installing the batteries. Insert
batteries you will hear two "Beep" tones
that will confirm that the clearing code
has been successful.
Vibration alarm
(Transmitter,
3M stickers
included)
*2
RF
Off
RF+Alarm
Battery
Compartment
Speaker
Vibration alarm (Transmitter)
1. Insert batteries to
the PIR alarms A and B.
2. For the PIR alarm A,
press the Code button
for 3 seconds by inserting
the screwdriver. A single
"Beep" will be heard.
3. Release the screwdriver and within 30 seconds:
3a. Remote key fob: press any button
3b. Vibration alarm: slide the switch to "RF" and
then knock on the vibration alarm. It will send a
wireless signal to the main unit.
4. The PIR alarm A will
give one "Beep" tone
to indicate that the
signal is received.
Paring the Transmitters to the PIR Alarm
30s
ON
OFF
BATTERY
-
+
BATTERY
-
+
BATTERY
-
+
Also pair the transmitters to the PIR alarm B by following the steps above. You can add up to
32 transmitters to each PIR alarm.
BATTERY
-
+
BATTERY
-
+
BATTERY
-
+
A
B
A
A
B
3c. Door/window magnetic sensor:
Separate the magnetic contact from
the alarm, the red indicator light
will be on.
3d. PIR alarm B: press the Code
button by inserting the screwdriver.
A
A
A
a
b
c
d
Once paired to the main unit and in the ARM mode if the vibration alarm is
triggered by a vibration, it will sound or send a wireless signal to the main unit.
The main unit will sound when it receives the wireless signal from the vibration
alarm. To disarm the alarm press the OFF button on the remote key fob.
Switch Operation:
OFF: Power off.
RF: When triggered, it itself will not sound but will send a wireless signal to
the main unit.
RF+ALARM: Three "Beep" tones will be heard when powered. When
triggered, it will send a wireless signal to the main unit and after 2 seconds it
itself will also sound for 8 seconds.
Before using the product, please remove the insulation sheets from all transmitters.
2 screws together with 2 plastic plugs (for installing the main unit brackets) and 4 3M stickers(for door/window
magnetic sensors)are included in each screw pack.
Firstly, install the bracket and attach the main unit to the
angle of the PIR alarm bracket and adjust the angle
accordingly.
The detecting range and
angle of the PIR alarm
①
②
90°
2-6M
Installation
PIR alarm
The main unit includes a receiver module and a transmitter module inside.