Specifications

ManualsBrandsRKC INSTRUMENT ManualsMedia ConverterCOM-JC

For detailed handling procedures and operations, refer to separate COM-JC

[For FB100/FB400/FB900] Instruction Manual (IMR01Y06-E).

The manual can be downloaded from the official RKC website:

http://www.rkcinst.com/english/manual_load.htm.

CC-Link Communication Converter

IMR01Y01-E5

Thank you for purchasing this RKC product. In order to achieve maximum

performance and ensure proper operation of your new instrument, carefully read all

the instructions in the manual. Please place this manual in a convenient location for

easy reference.

This manual describes the mounting, wiring and specifications only.

 Product Check



Safety Precautions

z This product is intended for use with industrial machines, test and measuring

equipment.

(It is not designed for use with medical equipment and nuclear energy.)

z This is a Class A instrument. In a domestic environment, this instrument may cause

radio interference, in which case the user may be required to take additional

measures.

z This instrument is protected from electric shock by reinforced insulation. Provide

reinforced insulation between the wire for the input signal and the wires for

instrument power supply, source of power and loads.

z Be sure to provide an appropriate surge control circuit respectively for the following:

− If input/output or signal lines within the building are longer than 30 meters.

− If input/output or signal lines leave the building, regardless the length.

z This instrument is designed for installation in an enclosed instrumentation panel. All

high-voltage connections such as power supply terminals must be enclosed in the

instrumentation panel to avoid electric shock by operating personnel.

z All precautions described in this manual should be taken to avoid damage to the

instrument or equipment.

z All wiring must be in accordance with local codes and regulations.

z To prevent instrument damage or failure, protect the power line and the input/output

lines from high currents with a protection device such as fuse, circuit breaker, etc.

z Prevent metal fragments or lead wire scraps from falling inside instrument case to

avoid electric shock, fire or malfunction.

z Tighten each terminal screw to the specified torque found in the manual to avoid

electric shock, fire or malfunction.

z For proper operation of this instrument, provide adequate ventilation for heat

dispensation.

z Do not connect wires to unused terminals as this will interfere with proper

operation of the instrument.

z Turn off the power supply before cleaning the instrument.

z Do not use a volatile solvent such as paint thinner to clean the instrument.

Deformation or discoloration will occur. Use a soft, dry cloth to remove stains from

the instrument.

z To avoid damage to instrument display, do not rub with an abrasive material or

push front panel with a hard object.

NOTICE

z This manual assumes that the reader has a fundamental knowledge of the

principles of electricity, process control, computer technology and communications.

The figures, diagrams and numeric values used in this manual are only for purpose

of illustration.

RKC is not responsible for any damage or injury that is caused as a result of using

this instrument, instrument failure or indirect damage.

RKC is not responsible for any damage and/or injury resulting from the use of

instruments made by imitating this instrument.

z Periodic maintenance is required for safe and proper operation of this instrument.

Some components have a limited service life, or characteristics that change over time.

Every effort has been made to ensure accuracy of all information contained herein.

RKC makes no warranty expressed or implied, with respect to the accuracy of the

information. The information in this manual is subject to change without prior notice.

No portion of this document may be reprinted, modified, copied, transmitted,

digitized, stored, processed or retrieved through any mechanical, electronic, optical

or other means without prior written approval from RKC.

1. MOUNTING

1.1 Mounting Cautions

(1) This instrument is intended to be used under the following environmental conditions.

(IEC61010-1) [OVERVOLTAGE CATEGORY II, POLLUTION DEGREE 2]

(2) Use this instrument within the following environment conditions:

• Allowable ambient temperature: −10 to +50 °C

• Allowable ambient humidity: 5 to 95 % RH

(Absolute humidity: MAX. W. C 29.3 g/m

dry air at 101.3 kPa)

• Installation environment conditions: Indoor use

Altitude up to 2000 m

(3) Avoid the following conditions when selecting the mounting location:

• Rapid changes in ambient temperature which may cause condensation.

• Corrosive or inflammable gases.

• Direct vibration or shock to the mainframe.

• Water, oil, chemicals, vapor or steam splashes.

• Excessive dust, salt or iron particles.

• Excessive induction noise, static electricity, magnetic fields or noise.

• Direct air flow from an air conditioner.

• Exposure to direct sunlight.

• Excessive heat accumulation.

(4)

Mount this instrument in the panel considering the following conditions:

• Ensure at least 50 mm space on top and bottom of the instrument for maintenance and

environmental reasons.

• Do not mount this instrument directly above equipment that generates large amount of

heat (heaters, transformers, semi-conductor functional devices, large-wattage resistors).

• If the ambient temperature rises above 50 °C, cool this instrument with a forced air fan,

cooler, etc. Cooled air should not blow directly on this instrument.

• In order to improve safety and the immunity to withstand noise, mount this instrument as

far away as possible from high voltage equipment, power lines, and rotating machinery.

High voltage equipment: Do not mount within the same panel.

Power lines: Separate at least 200 mm.

Rotating machinery: Separate as far as possible.

(5) If this instrument is permanently connected to equipment, it is important to include a

switch or circuit-breaker into the installation. This should be in close proximity to the

equipment and within easy reach of the operator. It should be marked as the

disconnecting device for the equipment.

1.2 Dimensions

109.5

125

(Unit: mm)

9.5

1.3 DIN Rail Mounting

 Mounting procedures

1. Pull down the mounting bracket at the bottom of the module (A). Attach the hooks

on the top of the module to the DIN rail and push the lower section into place on

the DIN rail (B).

2. Slide the mounting bracket up to secure the module to the DIN rail (C).

(B) Push

Mounting

bracket

DIN rail

(A) Pull down

 Removal procedures

Pull down a mounting bracket with a blade screwdriver (A). Lift the module from

bottom, and take it off (B).

1.4 Panel Mounting

 Mounting procedures

1. Pull down the mounting bracket (A) until locked and that a mounting hole appears.

2. Prepare one mounting bracket per module (B) sold separately (KSRX-55) and

then insert it in the rear of the terminal board at top of the module until locked but a

mounting hole does not disappear.

3. Mount each module directly on the panel with screws which are inserted in the

mounting holes of the top and bottom mounting brackets.

Recommended tightening torque: 0.3 N⋅m (3 kgf⋅cm)

The customer needs to provide the M3 size screws. Select the screw

length that matches the mounting panel.

(KSRX-55)

130.5 ± 0.2

(Unit: mm)

Mounting bracket

(Sold separately)

(A) Pull down

(B) Insert

Mounting dimensions

Mounting

holes

2. WIRING

2.1 Wiring Cautions

• To avoid noise induction, keep communication signal wire away from instrument

power line, load lines and power lines of other electric equipment.

• If there is electrical noise in the vicinity of the instrument that could affect

operation, use a noise filter.

− Shorten the distance between the twisted power supply wire pitches to

achieve the most effective noise reduction.

− Always install the noise filter on a grounded panel. Minimize the wiring

distance between the noise filter output and the instrument power supply

terminals to achieve the most effective noise reduction.

− Do not connect fuses or switches to the noise filter output wiring as this will

reduce the effectiveness of the noise filter.

• Power supply wiring must be twisted and have a low voltage drop.

• For an instrument with 24 V power supply, supply power from a SELV circuit.

• A suitable power supply should be considered in end-use equipment. The power

supply must be in compliance with a limited-energy circuits (maximum available

current of 8 A).

• Use the solderless terminal appropriate to the screw size (M3).

• Make sure that the any wiring such as solderless terminal is not in contact with the

adjoining terminals.

2.2 Terminal Configuration

−

24 V

Controller

communication

T/R(B)

T/R(A)

RS-485

Upper-side

terminal

Lower-side

terminal

Power supply

Ground

2 1

7 6 5 4

14 13 12

11 10 9 8

: The part of internal wiring

• As controller communication terminal No. 1, 4 and 5 are internally connected to

terminal No. 3, 6 and 7, any terminals can be used.

• As ground and power supply terminal No. 8, 9 and 12 are internally connected

to terminal No. 10, 11 and 14, any terminals can be used.

• Terminal No. 2 and 13 is not used.

COM-JC [For FB100/FB400/FB900] Installation Manual (IMR01Y01-E5) .................... 1

COM-JC [For FB100/FB400/FB900]

Quick Instruction Manual (IMR01Y11-E) ......... 1

COM-JC [For FB100/FB400/FB900]

Communication Data List (IMR01Y16-E) ........ 1

z An external protection device must be installed if failure of this instrument

could result in damage to the instrument, equipment or injury to personnel.

z All wiring must be completed before power is turned on to prevent electric

shock, fire or damage to instrument and equipment.

z This instrument must be used in accordance with the specifications to

prevent fire or damage to instrument and equipment.

z This instrument is not intended for use in locations subject to flammable or

explosive gases.

z Do not touch high-voltage connections such as power supply terminals,

etc. to avoid electric shock.

z RKC is not responsible if this instrument is repaired, modified or

disassembled by other than factory-approved personnel. Malfunction can

occur and warranty is void under these conditions.

WARNING

CAUTION

To prevent electric shock or instrument failure, always turn off the

power before mounting or removing the instrument.

WARNING

To prevent electric shock or instrument failure, do not turn on the

power until all wiring is completed. Make sure that the wiring is

correct before applying power to the instrument.

WARNING

(A) Pull down

(B) Lift and

take off

5.9 mm or less

3.2 mm or more

Recommended tightening torque:

0.4 N⋅m (4 kgf⋅cm)

Installation

Manual

[For FB100/FB400/FB900]

Summary of content (2 pages)

PAGE 1
NOTICE CC-Link Communication Converter All Rights Reserved, Copyright © 2005, RKC INSTRUMENT INC. IMR01Y01-E5 Thank you for purchasing this RKC product. In order to achieve maximum performance and ensure proper operation of your new instrument, carefully read all the instructions in the manual. Please place this manual in a convenient location for easy reference. This manual describes the mounting, wiring and specifications only.
PAGE 2
Connection diagram 2.3 Connection to PLC Method to connect z Relationship between number of occupied station/extended cyclic and number of controller connection Always connect a termination resistor between the DA and DB terminals of the module to be located at the far end. Termination resistor: 110 Ω ± 5 % 1/2 W The PLC (master station) and COM-JC make multi-drop connection in CC-Link dedicated cable Ver. 1.10.