2 Burner Camp Stove Model number: CS2153801-RG ASSEMBLY & OPERATING INSTRUCTIONS For Outdoor Use Only To installer or person assembling this appliance: Leave this manual with this appliance for future reference. This instruction manual contains important information necessary for the proper assembly and safe use of the appliance. Read and follow all warnings and instructions before assembling and using the appliance. Follow all warnings and instructions when using the appliance.
SAFETY SYMBOLS: The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout the manual. DANGER: Indicates an imminent hazardous situation which if not avoided will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
DANGER (a) Do not store a spare LP gas cylinder under or near this appliance; (b) Never fill the cylinder beyond 80 percent full; (c) If the information in (a) and (b) is not followed exactly, a fire causing death or serious injury may occur. WARNING Do not attempt to repair or alter the hose/valve/regulator for any “assumed” defect. Any modification to this assembly will void your warranty and create the risk of a gas leak and fire. Use only authorized replacement parts supplied by manufacturer.
completely thawed and towel dried before being immersed in the fryer. 13. Do not place empty cooking vessel on the appliance while in operation. 14. Use caution when placing anything in cooking vessel while the appliance is in operation. 15. In the event of rain, snow, hail, sleet or other forms of precipitation while cooking with oil or grease, cover the cooking vessel immediately and turn off appliance burners and gas supply. Do not attempt to move the appliance or cooking vessel. 16.
cooking liquid in order to prevent splashing or overflow. When removing food from the appliance care should be taken to avoid burns from hot cooking liquids. LP Tank Removal, Transport and Storage Turn OFF all control knobs and LP tank valve. Turn coupling nut counterclockwise by hand only – do not use tools to disconnect. Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve.
LP Tank Leak Test For your safety Leak test must be repeated each time LP tank is exchanged or refilled. Do not smoke during leak test. Do not use an open flame to check for gas leaks. LP tank must be leak checked outdoors in well-ventilated area, away from open flames or sparks. Use a clean paint brush and 50/50 soap and water solution. Use mild soap and water. Do not use household cleaning agents. Damage to gas train components can result.
PRODUCT DIAGRAM 4 1 2 3 2 3 Page 7 of 17 20160615-Ver.
COMPONENT LIST 1. Stove Body Assembly 2. Long Leg Qty: 1pc 3. Short leg Qty: 2pcs Qty: 2pcs 4. Wind Shield Qty: 1pc Page 8 of 17 20160615-Ver.
ASSEMBLY PROCEDURES Step 1. Insert the Long Legs (2) and Short Legs (9) into the leg holders of Stove Body Assembly (1) as shown. Then secure with the pre-assembled wing bolts. 1 2 3 2 3 Step 2. Attach the Wind Shield (4) to stove body assembly as shown. Make sure that the wind shield tabs are fully inserted into the frame of the stove body assembly. 4 Page 9 of 17 20160615-Ver.
Step 3. Your unit is fully assembled! Make sure to read and follow the Instruction Manual before using this appliance. When transporting or storing the appliance without tank attached, hook the regulator onto the stove frame to prevent damage to regulator. Remark: Before each use check all bolts to be sure that they are tight and secure. Page 10 of 17 20160615-Ver.
LEAK TEST GENERAL Although all gas connections on the appliance are leak tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. Periodically check the entire system for leaks following the procedures listed below. Before using your appliance you must check for leaks.
LIGHTING INSTRUCTIONS BEFORE LIGHTING WARNING Inspect the gas supply hose prior to turning the gas ON. If there is evidence of cuts, wear, or abrasion, the hose must be replaced prior to use. Do not use the appliance if the odor of gas is present. Only the pressure regulator and hose assembly supplied with the unit should be used. Perform the “LEAK TEST” according to the instructions before operating the appliance.
FLAME CHARACTERISTICS This procedure outlines how to check for proper burner flame characteristics. Burner flames should be blue and stable with little yellow tips, with no excessive noise, or lifting. If the flame is yellow, it indicates insufficient air. If the flame is noisy and tends to lift away from the burner, it indicates too much air. If any of these conditions exist, call our customer service line. Visually check the burner flames prior to each use. The flames should look like this picture.
BURNER Extreme care should be taken when removing the burner, as it must be correctly centered on the orifice before an attempt is made to relight the appliance. Frequency of cleaning will depend on how often you use the appliance. Spiders and small insects occasionally spin webs or make nests in the burner tube during transit and warehousing. These webs can lead to gas flow obstruction that could result in a fire in and around burner tubes.
TROUBLE SHOOTING Problem: Burner will not light Possible Causes: 1. LP cylinder fuel is used up. 2. Burner may be obstructed. 3. Cylinder valve may be closed. 4. Regulator is not properly seated on cylinder valve. Corrective Actions: 1. Change a new full LP cylinder. 2. Refer to section of “Burner Cleaning” at P.14 to clean the burner. 3. Check then open the cylinder valve. 4. Refer to section of “Connecting regulator to LP tank” at P.6 to reinstall regulator properly. Fire at control knob 1.
LIMITED WARRANTY 1. Manufacturer warrants this Product to be free from defects in workmanship and materials for a period of Ninety (90) days from the date of purchase, PROVIDED claims are submitted, in writing, with proof of purchase. 2.
Should you encounter any problem or Obtaining replacement parts CALL US FIRST. Do not return product to the store. WE CAN HELP. Rankam (China) Manufacturing Co. Ltd. 18/F., New Lee Wah Centre, 88 Tokwawan Road, Kowloon, Hong Kong Please contact Rankam Customer Service at customerservice@rankam.com or at (888) 837-1380, Mon to Fri, 8:00 a.m. – 5:00 p.m. Pacific Standard Time Made in China Page 17 of 17 20160615-Ver.