QUICK INSTALLATION GUIDE XR Series Wireless Arrays XR-2425H February 11, 2014
XR-2425H Quick Installation Guide is a registered trademark of Xirrus, Inc. All other trademarks and brand names are marks of their respective holders. All rights reserved. This document may not be reproduced or disclosed in whole or in part by any means without the written consent of Xirrus, Inc. Please see Warranty and License Agreements in the Wireless Array User’s Guide.
XR-2425H Quick Installation Guide XR-2425H Quick Installation Guide The XR-2425H Hardened Wireless Array provides Xirrus wireless technology in a hardened case for installation outdoors and in other harsh environments. This guide describes how to install the XR-2425H on a pole or wall and execute the initial power up of the Array. The pole or wall can be a structure that is installed at ground level or on a roof. The XR-2425H is not compatible with other Xirrus mounting options.
XR-2425H Quick Installation Guide 2425H. The XR-2425H is powered by one injector port rated at 30W or higher. See the Installation Guide for your PoE device for more information. NOTE: Xirrus-supplied PoGE Injectors and switches must be installed and used indoors. 2) Choose a Suitable Location The XR-2425H is tested to IP65 water proof and dust proof requirements to protect against severely wet and dusty environments.
XR-2425H Quick Installation Guide 4) Attach the Mounting Plate to the Array The accessory kit includes a mounting plate. Mounting plate dimensions are included in the Drawings section at the end of this guide. The mounting plate can be used for wall or pole mounting by reversing the side of the plate exposed. Attach the mounting plate to the Array using the eight provided screws in the locations indicated below (secure in at least 4 places).
XR-2425H Quick Installation Guide Hand tighten the Band-It strap through the pole mounting bracket, thread it through the strap buckle and then bend the strap back. Using the Band-It tool, place the tool onto the strap. Rotate the Band-It tool so that it can pull the excess strap through the buckle and turn the crank until the strap is very tight. Once the strap is satisfactorily tight, rotate the Band-It tool back so that the strap cannot slide back through the buckle.
XR-2425H Quick Installation Guide Your installation should now appear as shown here. Using a hammer, bend back and flatten the remaining strap. Using a hammer, bend and flatten the two tabs on the buckle to hold the flattened strap end in place. The completed attachment should have the mounting bracket firmly seated against the pole. One band should be enough for most installations however a second band can be used for additional mounting security.
XR-2425H Quick Installation Guide 6) Ground to Earth Ground WARNING: This equipment must be externally grounded using a customer-supplied ground wire before power is applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. The mechanical installation must ensure that the Array is grounded to earth ground to dissipate static electric charge that may develop due to wind.
XR-2425H Quick Installation Guide This will not seat properly in the waterproof connector, and the assembly will not be watertight. The components of the connector are shown in the photo below in the order that they are placed onto the Ethernet cable, and also shown in more detail as a color-coded drawing. You will perform a few assembly steps below before sliding the parts onto the cable. Seat the O-ring (shown in red) on the connector body (gray) at its RJ45 jack side.
XR-2425H Quick Installation Guide Snug all of the components together as shown, but leave the RJ45 connector protruding. Tighten the sealing nut lightly, making sure that the RJ45 connector is rotated so that it will seat easily in the connector body later. Plug the RJ45 connector into the port on the bottom of the XR-2425H, making sure that its tab clicks in place for a secure connection. Seat the RJ45 connector correctly in the connector body.
XR-2425H Quick Installation Guide 9) Connect the Antenna IAP2 IAP1 IAP3 IAP4 The XR-2425H has eight RP-TNC connectors for the antennas, two for each of the four IAPs. Both of the antenna connectors for each IAP (for example, IAP1 ANT1 and IAP1 ANT2) must be attached to antenna leads for the same frequency band (for example, 5GHz), and that IAP must be set to that band on the Array.
XR-2425H Quick Installation Guide 10) Zero-Touch Provisioning and Ongoing Management Most customers employ the Xirrus Management System (XMS) for the initial setup and continuing management of Xirrus devices. XMS users can readily set up their new devices for zero-touch provisioning and ongoing maintenance via the following platforms. XMS Cloud Next Generation (XMS-CL-9500-x) XMS in the Cloud performs zero-touch provisioning as shown in this quick video guide: http://www.xirrus.
XR-2425H Quick Installation Guide Dimensions XR-2425H Dimensions Depth is 4.2 in (10.7 cm), including the mounting bracket. 11.8 in 30 cm Weight: 7.5 lbs (3.4 Kg) 11.4 in 28.9 cm Mounting Bracket Dimensions 3.2 in 8.1 cm 13.3 in 33.7 cm Depth = .5 in; 1.
XR-2425H Quick Installation Guide Notices, Warnings, & Compliance Statements Notices Read all user documentation before powering this device. Please verify the integrity of the system ground prior to installing Xirrus equipment. Additionally, verify that the ambient operating temperature does not exceed 65°C. Software used by the modular Arrays (APs) is covered by the Xirrus Software License and Product Warranty Agreement.
XR-2425H Quick Installation Guide Warnings GENERAL SAFETY GUIDELINES WARNING: This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. WARNING: Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
XR-2425H Quick Installation Guide CAUTION: Xirrus PoGE Injectors rely on the building’s installation for over current protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A (U.S.) or 240 VAC, 10A (International) is used on all current-carrying conductors. EXTERNAL ANTENNAS WARNING: In order to comply with radio frequency (RF) exposure limits, the antennas for this product should be positioned no less than 26 cm from your body or nearby persons.
XR-2425H Quick Installation Guide Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Consult the dealer or an experienced wireless technician for help.
XR-2425H Quick Installation Guide Industry Canada Statements and Warnings Industry Canada Notice and Marking: This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
XR-2425H Quick Installation Guide High Power Radars: High power radars are allocated as primary users (meaning they have priority) in the 5250MHz to 5350MHz and 5650MHz to 5850MHz bands. These radars could cause interference and/or damage to Wireless LAN devices used in Canada. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-àd., qu’ils ont la priorité) pour les bandes 5 250 - 5 350 MHz et 5 650 - 5 850 MHz.
XR-2425H Quick Installation Guide Latviski [Latvian] Šī iekārta atbilst Direktīvas 1999/5/EK būtiskajā prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šis įrenginys tenkina 1995/5/EB Direktyvos esminius reikalavimus ir kitas šios direktyvos nuostatas. Nederlands [Dutch] Dit apparant voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de Richtlijn 1995/5/EC.
XR-2425H Quick Installation Guide WEEE Compliance: Natural resources were used in the production of this equipment. This equipment may contain hazardous substances that could impact the health of the environment. If you need more information on collection, re-use and recycling systems, please contact your local or regional waste administration. Please contact Xirrus for specific information on the environmental performance of our products.
XR-2425H Quick Installation Guide Η δη ιουργβάικτ ωνεξωτερικο ρουστη ζ νησυ νοτ των 5470–5725 ΜΗz ε ιτρ ετάιωνο ετάά όάδειά της ΕΕΤΤ, ου ορηγεβτάι στερά ά ό σ φωνη γν η του ΓΕΕΘΑ. Ερισσότερες λε τομ ρειεωστο www.eett.gr Italy: This product meets the National Radio Interface and the requirements specified in the National Frequency Allocation Table for Italy. Unless this wireless LAN product is operating within the boundaries of the owner’s property, its use requires a “general authorization.
XR-2425H Quick Installation Guide Only antennas provided by Xirrus for use with the product should be installed. The use of any other antennas may cause damage to the Arrays or violate regulatory emission limits and will not be supported by Xirrus. International Guidelines for Exposure to Radio Waves The Xirrus Arrays include radio transmitters and receivers.
XR-2425H Quick Installation Guide Industry Canada Guidelines for Exposure to Radio Waves The Xirrus Arrays include radio transmitters and receivers. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health.
XR-2425H Quick Installation Guide Notes
XR-2425H Quick Installation Guide Customer Support The Xirrus Customer Support Website provides online documents and tools for troubleshooting and resolving technical issues with Xirrus products and technologies. Access to all tools on the Xirrus Customer Support Website requires a login user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL: http://support.xirrus.