TYPE OF EXHIBIT: INSTALLATION AND OPERATING INSTRUCTION MANUAL FCC PART: 2.1033 (b)(3) MANUFACTURER: RITRON, INC. 505 West Carmel Drive Carmel, IN 46032 MODELS: RQT-433-RCVR TYPE OF UNIT: 433.92 MHz Keyfob Receiver FCC ID: AIERIT32-433-RCVR DATE: January 24, 2012 Included in this exhibit is a draft copy of the User Manual for RITRON Model RQT-433-RCVR 433 MHz Keyfob Receiver. This manual provides the end user with installation and operating instructions. Signed: Michael A.
RQT-433-RCVR 433.92 MHz Keyfob Receiver Owner’s Manual Call 800-USA-1-USA for the right Wireless Solutions to your communication needs. Ritron, Inc. P.O. Box 1998 • Carmel, Indiana 46082-1998 • USA Phone: 317-846-1201; 800-USA-1-USA (800-872-1872) Fax: 317-846-4978 Email: ritron@ritron.com Ritron Publication 145000082 Rev. A 01-12 © 2011 Ritron, Inc. All rights reserved. Ritron, Patriot, Jobcom, OutPost, GateGuard, Quiet Call and Quick Assist are registered trademarks of Ritron, Inc.
Table of Content RQT-433-RCVR FCC Part 15 Statement RQT Models and Keyfobs ............................................. 2 RQT-433-RCVR FCC Part 15 Statement ..................... 2 General Information ...................................................... 3 RQT Radio Operation ................................................... 3 Effect on RQT Radio Battery Life.................................. 3 RQT-KEYFOB Operation .............................................. 4 RQT-KEYFOB Battery Replacement .......
General Information The RQT-433-RCVR is a 433.92 MHz keyfob receiver designed for use with the Ritron RQT Series transmitter. When installed, the RQT-433-RCVR allows the user to activate RQT pre-recorded messages by pressing a small keyfob transmitter. Ritron model keyfobs are preset to activate 1 of 8 RQT messages. Simply record your desired voice message into the RQT Series transmitter using the RQT PC Programmer and you are ready to go.
RQT-KEYFOB Operation RQT-KEYFOB Battery Replacement When operating a keyfob transmitter the best performance is achieved with the keyfob held between the thumb and forefinger, with the top of the keyfob uncovered and vertical (as shown) The keyfob utilizes a standard CR2032 lithium button cell. In normal use, it can provide up to 1 year of operation. It is important to understand that only one keyfob transmitter at a time can be activated within a reception area.
RQT-KEYFOB FCC Part 15 Instructions This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RQT Radio Programming Ritron Models with the RQT-433-RCVR installed: Programming an RQT transmitter (equipped with the RQT-433-RCVR) for keyfob operation requires Ritron PC Programmer RQT-PCPS or RQT-BASIC-PCPS revision 1.1.0 or higher. A programmer update to this revision is available at www.ritron.com. RQT-151-RCVR RQT-152-RCVR RQT-451-RCVR RQT-452-RCVR RQT-151M-RCVR RQT-152M-RCVR 2. Select the input you would like to program for Keyfob operation.
Programmable RQT Radio Attributes Latch On - When Latch On is selected, the RQT will ignore decoded signals from the keyfob until after the transmission schedule have been completed. If not set, the RQT will transmit the recorded message every time is receives the correct code. EXAMPLE: RQT-KEYFOB-1 is scheduled for 2 transmissions, 30 seconds between transmissions.
Changing the Address For convenience, the RQT-433-RCVR keyfob receiver and all Ritron keyfobs come from the factory set to the same address. This establishes a relationship between a single RQT-433-RCVR receiver and multiple keyfobs with different codes. For the vast majority of users the address does not need to be changed. Occasionally the user may want to change the address to: • Install two or more RQT-433-RCVR keyfob receivers in the same location.
Specifications RQT-433-RCVR RQT-KEYFOB Receive Frequency Center Frequency Accuracy Sensitivity Modulation Type Antenna FCC Part FCC ID Input Voltage Operating Voltage Input and Output Logic Interconnection Current - Standby Current – w/Antenna Disable Temperature 433.92 MHz +/- 50 kHz -112dBm typical OOK Helical wound ¼ wave 15B AIERIT32-433-RCVR 6-12 VDC 5.0 VDC 0-5 VDC +V in Ground Valid Decode Out Clock In Antenna Disable In Data Out 5.9 mA 14.