4.6 Job Separation The setting of Job separation (set with the printer driver) can be changed while printing of the current job is performed. # Settings OFF Job Separation is not performed. Between Jobs Separation paper is inserted between jobs. Every Division Separation paper is inserted every division. When collated printing is directed by the printer driver, separation paper is inserted between sets. When non collated printing is directed, separation paper is inserted between pages.
4.7 Print Density You can manually change the print density. The density of overall printing is set. To adjust specific colours or to change the halftone reproduction method, use the "Image processing" tab of the printer driver to adjust or process the image using the application software.
4.8 Paper Ejection Sets the position and adjustment of the Eject Wing and the Auto Stacking Tray. If an optional HC Finisher is connected, this menu is not displayed. # Settings 4.8.1 Eject Wing 4.8.2 Stack Guide Adjusts the Eject Wing so that the position changes for proper paper arrangement when printed paper is ejected. Auto: The Eject Wing is automatically adjusted to optimum position based on the type and size of paper. Special: The Eject Wing can be set according to special paper.
1 Press the MENU Key. 2 Press the or "Configuration." 3 4 Press the or "Paper Ejection." 5 Press the OK Key. key to display key to display The submenu of "Paper Ejection" is displayed. Press the OK Key. 4.8.1 Eject Wing 1 Ensure that "Eject Wing" is displayed. 3 Press the 2 Press the OK Key. 4 Press the OK Key. or key to select. When the screen in step 1 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. 4.8.
4.8.3 Stack Guide Adjust 1 Press the or key to display "Stack Guide Adjust." 3 To adjust the Side Guide positions, press the or key , and to adjust the End Guide position, press the or key. Only the arrow that corresponds to the pressed key is displayed therefore the relevant value changes. 2 2 Press the OK Key. 4 After setting is complete, press the OK Key. When the screen in step 1 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. 4.8.
4.9 Temp Data Clear If a check mark is placed at [Keep the last page of the job in the printer.] in [Controller setting 2] - [Initial setting] of [Administrator] of RISO Console, the last page of previous printing (last sheet in case of duplex printing) is left in the controller as retained data. If retention of data after printing is not desired because of a confidential document, the data can be cleared.
4.10 Image Area (Maximum Print Area) With this machine, a certain area of space is left along the edges of paper regardless of the original size. Normally, use the setting "Standard." If the image is larger than the printable area, the relevant part of the image is not printed. (Reduction is not performed.) # Settings Standard Maximum Printing can be performed into the area 3mm (1/8") inside from the sides of paper.
4.11 Cover Sheet Tray (Only when the HC Finisher is connected) Set the size and type of paper to be loaded in the Cover Sheet Tray in the optional Finisher. Be sure to set them when you have changed the type or size of paper. # Settings 4.11.1 Paper Size Can be selected from Auto, A3, B4, A4, B5, A4-R, B5-R, Ledger, Legal, Letter, Letter-R. 1 Press the MENU Key. 2 Press the or "Configuration." 3 Press the OK Key. 4 Press the or "Cover Sheet Tray" 5 Press the OK Key.
Menu 5 Administration Sets basic information of the printer such as paper type entry, maintenance, and initial setting. The items set here are effective until the setting is changed regardless of when the power is on or off. # Functions The functions that can be set are shown below. ! 5.1 Paper Size Entry"p.2-32 Five paper sizes such as non-standard sizes can be registered. ! 5.2 Paper Type Entry "p.
5.1 Paper Size Entry Five non-standard paper sizes can be registered. When using non-standard size paper, be sure to register the size in advance. Registered values are displayed in Paper Size of "4.1.1 Standard Feed Tray," "4.2.1 Feed Tray 1," and "4.3.1 Feed Tray 2." If the paper sizes have been registered, the registered values will be displayed.
5.2 Paper Type Entry If any paper other than printer recommended paper is used or paper is not fed properly, it could result in poor print quality. You should register the paper type and feeding according to the paper type specifications. The registered setting is displayed in Paper Type of "4.1.2 Standard Feed Tray," "4.2.2 Feed Tray 1," and "4.3.2 Feed Tray 2." Also if printer recommended paper is used and paper is not fed properly because of operating environment or the like, the setting can be changed.
5.2.1 Registering a New Paper Type 1 2 Use steps 1 to 4 (" "p.2-31) to display "Administration." 8 Press the OK Key. The screen in step 6 appears again. Press the or key to display "Paper Type Entry." Set the Paper Type. 9 3 Press the OK Key. 4 Press the or key to display the desired number to be registered. Press the or "Paper Type." key to display 10 Press the OK Key. The submenu of paper type appears. 5 11 Press the Press the OK Key. The submenu of Registration appears.
15 Press the or key to select the desired paper type. 16 Press the OK Key. The screen in step 13 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. 5.2.6- Changes the Paper feed control of the existing paper type. 1 Use steps 1 to 4 (" "p.2-31) to display "Administration." 2 Press the or key to display "Paper Type Entry." 3 Press the OK Key. 4 Press the or key to display the desired paper type to change the settings. 5 Press the OK Key.
5.3 Separation Paper If you use "4.6 Job Separation", specify the feed tray in which the separation paper is loaded. # Settings The separation paper can be used even if the size and the orientation are different from those of the printer paper. OFF The separation paper tray is not specified. Printing stops for a few seconds in place of insertion of separation paper. Standard Feed Tray The Standard Feed Tray is used for separation paper. Feed Tray 1 Feed Tray 1 is used for separation paper.
5.4 Count Management The number of printed sheets can be checked. • The number of sheets that have been ejected in the Paper Receiving Tray is displayed. • For copy count, in duplex printing, each side is counted, and therefore one sheet of both sides is counted by two. Since the paper transfer path varies depending on the functions that you use, one sheet in simplex printing may be counted as two. • For Count Pattern, one sheet is counted as one regardless of simplex or duplex printing. # Settings 5.4.
Count No. Paper Size Number 15 Size No.1 16 Size No.2 17 Size No.3 18 Size No.4 19 Size No.5 20 Size No.6 21 Size No.7 22 Size No.1 23 Size No.2 24 Size No.3 25 Size No.4 26 Size No.5 27 Size No.6 28 Size No.7 Simplex/ Duplex Colour/ Monochrome Simplex Monochrome Duplex 5.4.1 Copy Count 1 2 Use steps 1 to 4 (" "p.2-31) to display "Administration." 5 The total number of sheets is displayed. Press the or key to display "Count Management." 6 2-38 Press the OK Key.
5.4.3 Count Pattern 1 Use steps 1 to 4 (" "p.2-31) to display "Administration." 2 Press the or key to display "Count Management." 2 3 Press the OK Key. 4 Press the or "Count Pattern." 5 Press the OK Key. 6 Press the keys to move the cursor, and press the keys to input the count No. of Count Pattern. 7 Press the OK Key. key to display The number of sheets of the specified count pattern is displayed. 8 After checking is complete, press the OK Key.
5.5 Head Maintenance Perform maintenance of the print head section. You can also set the cycle of automatic cleaning. Use this function when there is a problem of image quality. For example, if parts of print images are blurred, white lines appear, a specific colour is light and when the printer will not be used or has not been used for a long time. In the factory default setting, the cleaning cycle is set to 500 sheets. # Settings 5.5.
5.5.5 Normal Cleaning 1 Use steps 1 to 4 (" "p.2-31) to display "Administration." 2 Press the or key to display "Head Maintenance." 3 Press the OK Key. 4 Press the or "Normal Cleaning." 5 Press the OK Key. 6 After checking the message, press the OK Key. 2 When message "Cleaning Print Head" blinks, cleaning is performed. After cleaning is complete, the screen in step 4 will appear again. To exit the setting, press the PRINT/PAUSE key. key to display 5.5.
5.6 Configuration Information Print Configuration settings are printed in a list. Current printer settings and menu settings can be checked in a list. # Settings 5.6.1 System Information Information such as printer memory capacity, firmware version, and IP address can be checked in a list. 5.6.2 Menu Setting The menu settings made on the operation panel can be checked in a list. 5.6.4 Count Pattern The result of "5.4.
5.6.1 System Information 1 2 Use steps 1 to 4 (" "p.2-31) to display "Administration." Press the or "Config Info Print." 5 Press the OK Key. 6 After checking the message, press the OK Key. key to display When printing is complete, the screen in step 4 will reappear, and you can continue setting. 2 3 Press the OK Key. 4 Press the or key to display "System Information." 7 Press the PRINT/PAUSE Key. A list of system information is printed. 5.6.2 Menu Setting 1 Use steps 1 to 4 (" "p.
5.6.4 Count Pattern 1 2 Use steps 1 to 4 (" "p.2-31) to display "Administration." 6 To cancel the setting, press the Cancel key. Press the or "Config Info Print." key to display 7 2-44 After checking the message, press the OK Key. 3 Press the OK Key. 4 Press the or "Count Pattern." 5 Press the OK Key. Press the PRINT/PAUSE key. A list of "5.4.3 Count Pattern" and the count of the finisher function (only if an optional finisher is connected) is printed.
5.7 Network Configuration If the printer is connected to a network and all the conditions shown below are satisfied, you can register the network configuration. If the conditions below are not satisfied, you can check the settings. • DHCP OFF • IP address is "000.000.000.000" To change the setting, use "Administrator" of RISO Console or supplied software "RISO IP Setting Tool." The settings will be effective after the printer is restored from the sleep mode. For details, consult your network administrator.
10 Press the keys to move the cursor, and press the keys to enter the values. 12 Press the Sleep Key to turn off the power and then on again. After message "Shutting Down" disappears and the Power Key becomes orange, press the Sleep Key again to turn ON the power. 11 After checking the message, press the OK Key. Message "Registered. Restart Printer" is displayed. 5.
5.8.18 Print Mode Auto-ON Sets whether or not the print mode is automatically turned on when the printer is not used for a certain time with the print mode OFF. ON: The print mode will be automatically turned off. OFF: The print mode will not be turned off. 5.8.19 Print Auto-ON Time Sets the time that elapses until the print mode is turned on when "Print Mode Auto-ON" is set to "ON." The time can be set to 1 to 60 minutes. 5 5.8.
5.8.1 Sleep 1 2 Use steps 1 to 4 (" "p.2-48) to display "Administration." Press the or "Initial Setting." 3 Press the OK Key. 4 Press the "Sleep." or 5 Press the OK Key. 6 Press the or OFF. 7 Press the OK Key. key to display or key to select ON When the screen in step 4 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. key to display 5.8.2 Waiting Time 1 2-48 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting.
5.8.3 Beep Sound -Key 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting." 2 Press the or key to display "Beep Sound -Key." 3 4 Press the or OFF. 5 Press the OK Key. or key to select ON 2 When the screen in step 2 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. Press the OK Key. 5.8.4 Beep Sound -Status 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting.
5.8.5 Beep Sound -Error 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting." 2 Press the or key to display "Beep Sound -Error." 3 4 Press the or OFF. 5 Press the OK Key. or key to select ON When the screen in step 2 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. Press the OK Key. 5.8.7 Displayed Language 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting.
5.8.17 Tray Selection Rule 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting." 2 Press the or key to display "Tray Selection Rule." 4 Press the 5 Press the OK Key. or key to select. When the screen in step 2 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. 3 2 Press the OK Key. 5.8.18 Print Mode Auto-ON 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting.
5.8.20 Menu Auto-Shut OFF 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting." 2 Press the or key to display "Menu Auto-Shut OFF." 3 4 Press the or OFF. 5 Press the OK Key. or key to select ON When the screen in step 2 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. Press the OK Key. 5.8.21 Menu Shut OFF Time 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting.
5.8.23 Stand-by Period 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting." 2 Press the or "Stand-by Perid." 4 Press the keys to move the cursor, and press the keys to input the desired time. key to display 2 5 3 Press the OK Key. When the screen in step 2 reappears, you can continue setting. To exit the setting, press the PRINT/PAUSE key. Press the OK Key. 5.8.50 Head Recovery 1 Use steps 1 to 3 of "5.8.1 Sleep" (" "p.2-48) to display "Initial Setting.
Menu 6 Feed Tray Selection If the paper conditions of data received from a computer and the setting of "5.8.17 Tray Selection Rule" do not match the conditions of any of the Standard Feed Tray and other feed trays, printing will not start. In this case, you can specify the Standard Feed Tray or another feed tray where the printer paper is set and start printing with no trouble. # Selectable Feed Trays Selectable feed trays Selectable feed trays are shown below. Auto Normally, set "Auto.
Menu 7 Job Clear Cancels the currently printed job and clears the data. What is Job? When data is transmitted from a computer to the printer, the controller processes the data and sends the print data to the FORCEJET™ ENGINE. The processed data is called "Job." "Job" means the data shown below. • Data suspended temporarily • Data for which additional printing is set with the Temporary Data Retrieve function. 1 Press the MENU Key. 2 Press the Clear." 3 Press the OK Key. 4 Check the message.
2-56
Chapter3 Troubleshooting This chapter describes the causes of and measures against trouble indicated with an error message displayed on the Operation Panel or lighting symbol. This chapter also describes how to remove jammed paper and replacing an ink cartridge.
Explanation of Set Error Display If trouble occurs during printing, printing stops and a symbol lights up on the Operation Panel or an error message appears in the display. You can check the location based on the symbol or number and see the information from the message in the display. Symbol Display on Operation Panel A symbol indicating the relevant portion or type lights up. It may indicate a paper jam or ink cartridge replacement.
FORCEJET™ Link Symbol HC5500 Series realizes high speed printing by performing the optimum data processing and colour management with the printer controller and adjusting print speed, paper size, paper quality, and ink quantity totally with the FORCEJET™ ENGINE. The FORCEJET™ Link Symbol indicates whether each printing related section functions properly. If colour management cannot be performed properly because, for example, an ink cartridge is not set, the FORCEJET™ Link Symbol goes out.
Y00-000 Ink Replacement Error Lighting location Message Solution The supply in the ink cartridge runs out. Set a new ink cartridge. "p.3-18 Z00-000 Check Settings Error If a cover has not been securely closed or in situation of an ink cartridge or Feed Tray which has not been properly set. Check the location, take proper measures, and close the cover. Lighting location Message Solution If an ink cartridge has not been properly set, make sure to check if the cartridges are securely inserted. "p.
Lighting location Message Solution If Standard Feed Tray has not been properly opened, open the Standard Feed Tray properly. If a cover has not been securely closed, make sure to check the location indicated by an indicator and close the cover securely. 3 HC Auto Stacker is not in place. Be sure to attach it to the printer. Jam Release Cover has not been securely closed, be sure to close it.
S00-000 System Error Lighting location Message (Nothing is lit.) X00-000 H00 Solution An error occurs in the printer. If the same message appears even when the power is turned off and then on again, contact your local dealer (or service representative). At this time, report also the error number indicated in the Message Display. "p.
M00-000 Maintenance Call Lighting location Message Solution The Ink Drain Tank is almost full. Contact your local dealer (or service representative). (Nothing is lit.) (No message.) (Nothing is lit.) When the Maintenance Call Indicator lights up, periodical maintenance is required. Contact your local dealer (or service representative). 3 No colour profile corresponding to the installed ink is provided. Contact your dealer (or service representative).
Lighting location Message Solution If the guides in the Auto Stacking Tray are not properly set, make sure to check the Auto Stacking Tray. Paper is jammed in the HC Auto Stacker. Open the Jam Release Cover to remove paper. Press the Cancel Key on the printer after removing jammed paper."p.3-17 Paper ejected onto the Shift Tray of the HC Auto Stacker exceeded the capacity of the tray. Remove paper from the Shift Tray. Open the Jam Release Cover once and then press the Cancel Key on the printer.
Paper jam occurs If a paper jam occurs in the printer or paper is not fed, printing stops, the JAM indicator, and the number indicating the jam location will light up. In this case, remove the jammed paper and press the PRINT/PAUSE Key, printing will resume. Since this unit performs high speed printing, paper jams may occur at multiple locations. In this case, remove all the jammed paper.
(2) Paper Jam on the Transfer Roller 1 Open the Front Cover. 2 Turn Dial A and remove the paper from the Transfer Roller side. 3 Close the Front Cover. (3) Paper Jam in the Paper Receiving Section 1 Pull out the jammed paper and remove it. Pull out the jammed paper from the side of the Paper Receiving Tray. ! 3-10 If it is not easy to pull out, do not pull it forcibly because the paper might be torn. Open the Front Cover and remove the paper from the side of the Transfer Roller.
(4)Paper Jam in the Right of the Transfer Unit 1 Open the Right Transfer Path Cover. 3 Close the Right Transfer Path Cover. 3 2 Remove the paper. When the HC Auto Stacker is connected. 1 While pressing the Release Lever, pull the Auto Stacker to the side. 2 Open the Right Transfer Path Cover. 3 Remove the jammed paper. 4 Close the Right Transfer Path Cover.
5 Return the Auto Stacker to its original position. (5)Paper Jam in the Duplex Transfer Unit 1 Open the Front Cover. 3 Turn Dial B. If the paper is removed, proceed to step 7. ! 2 Lift the tab at the left side of the Reversing Path Cover and lock it. 4 3-12 Turn Dial B several times to check to see if any paper remains. Multiple sheets of paper may have jammed. Turn the dial repeatedly until no paper can be removed. Pull out the Duplex Transfer Unit.
5 Open the unit and check inside. If paper remains, remove it. 6 Return the Duplex Transfer Unit to its original position. 7 Return the tab at the left of the Reversing Path Cover to its original position. 8 Close the Front Cover.
(6)(7)(8) Paper Jam in the Left of the Transfer Unit 1 Open the Front Cover. 2 Lift the tab at the left side of the Reversing Path Cover and lock it. 3 4 3-14 While turning Dial B in the direction indicated by the arrow, remove the paper. If the paper cannot be removed, open the Left Transfer Path Cover and remove the paper. 5 If the paper cannot be removed, while turning Dial C in the direction indicated by the arrow, remove the paper.
(17)(18)(19) Paper Jam in Paper Feed Tray 1/ / Paper Feed Tray 2 1 Pull out the Feed Tray. 3 2 Remove the jammed paper. 3 If the paper cannot be removed, open the Transfer section door at the left side of the Feed Tray and remove the paper. 4 Close the door and return the Feed Tray.
(20) Paper Jam in the Transfer Unit 3-16 1 Open the Front Cover. 2 Turn the Transfer Lock Lever to the left and turn down the tab to the right. 3 Remove the jammed paper. 4 Return the tab to its original position and turn the Transfer Lock Lever to the right. 5 Close the Front Cover.
(21) Paper Jam in HC Auto Stacker (option) 1 Open the Jam Release Cover. 3 2 Remove the jammed paper. 3 Close the Jam Release Cover.
Ink Cartridge Replacement If ink runs out, the INK CARTRIDGE indicator and the indicator that shows the location of the empty cartridge will light up, printing will be halted. Be sure to check the colour of the Ink Cartridge and replace it. Black (K) Cyan (C) Magenta (M) Yellow (Y) Ink Cartridge This section describes the notes in handling an Ink Cartridge. Handling of Ink Cartridge is also described in "Safety Precautions" ("p.v) and "Before Starting to Use" ("p.vii, p.viii).
• Do not release the ink left in the cartridge into a sewer or personal disposal unit. • Used Ink Cartridges are collected by a service representative. After use is complete, attach the cap and put the cartridge into the inner bag and packing material. When attaching the cap or packing, be sure to hold the Ink Cartridge with the cap up. Caution : Do not turn the Ink Cartidge upside down. As an example, procedure for replacing the Yellow (Y) Ink Cartridge ((14) is light) is described.
Other Trouble The printer does not operate. Problem Cause and Solution Even if the power is turned on, nothing appears on the Operation Panel. Be sure to check the following. Test print is normally output but data from a computer cannot be properly printed. Make sure to check the network setting and the IP address setting before installing the printer driver again. • • • • If the power plug is inserted into the outlet. If the power cord is securely connected to the unit.
The printer does not operate according to the setting. Problem Cause and Solution "Job separation" is set in the printer driver screen but job separation cannot be performed. "Separation Paper" is set to "OFF" in the menu setting. If "5.3 Separation Paper" of the menu setting is set to "OFF," job separation paper is not inserted. (If "OFF" is set, printing stops for a few seconds at the time of separation.) To insert job separation paper, select the desired tray at "5.
Others Problem Cause and Solution Print speed is too low. The guides in the Standard Feed Tray (Feed Tray) do not fit the paper width. The paper size is judged based upon the guide positions, and print speed depends on specifications of paper size. Adjust the stack guides securely to the width of the paper. A paper jam occurs each time printing is performed. Too much paper is loaded in the Standard Feed Tray or other Feed Trays.
Problem Although paper is set, "No Paper" error can occur. Cause and Solution [Paper size] and [Paper type] set in the printer driver screen do not match those in the menu setting on the printer. Even if proper paper is loaded in the feed tray, if the settings of "Paper Size" and "Paper Type" of the menu setting on the printer are not correct, "No Paper" error occurs. Set the conditions of the feed tray according to the paper in the feed tray. Alternatively, a condition is set at "Tray selection Rule.
3-24
Chapter4 Appendix 4-1
List of Options A variety of options are available for convenient use of this unit. For purchase, contact your dealer (or service representative) for inquiry. RISO Scanner HS2000 By connecting a scanner and a display monitor (products specified by our company), you can perform high-speed full-colour printer copies. Finisher Functions By connecting an HC Finisher to this machine, you can perform automatically postprocessing of printing such as stapling, punching, booklet creation at a high speed.
Consumables • Note that specifications and types of consumables are subject to change without prior notice. • For the price, contact your local dealer (or service representative) for inquiry. Ink Cartridge ! Use ink cartridges specifications as directed by our company. Do not use other products because use of improper consumables may cause a failure or trouble. Colour Quantity Unit NET.
Specifications ! Main Body Print Type Line Type Ink Jet System Resolution Normal: 600 dpi or equivalent Fine: 900 dpi or equivalent (Line Smoothing: ON) Print Head Piezo type, Physical Resolution 300 dpi, 8 Gradation Ink Oil-based pigment type, Cyan/Magenta/Yellow/Black, 1,000ml for each Print Speed (*1) 120 ppm, Duplex 48 ppm (A4, Landscape, Normal mode) Duplex Printing Standard Printer Collate Standard Paper Size Paper Feed Tray: Max. A3 (297mm × 432mm)/Ledger(11" × 17") Min.
! HC AUTO STACKER (Option) Paper Size 100mm (*1) - 305mm x 148mm - 432mm (315/16" (*1) - 12" x 513/16" - 17") Paper Weight 46 g/m2 to 210 g/m2 (12-lb bond to 56-lb bond) Paper Tray Capacity (*2) It varies according to paper size.
Principal Functions Web Console Function Colour Management "ComColor™ Standard" colour management is provided.
! Controller Section (If the RISO Controller HC3R-5000 is installed) Principal Specifications Principal Functions Web Console Function Printer that can be connected RISO HC5500T CPU Intel® Celeron® 2.9GHz Memory Capacity 256MB HDD 80GB (user available area: 70GB) User available area: Job receiving area, Storage area OS Linux Interface Ethernet / 1000Base-T, 100Base-TX, 10Base-T Type Outside unit type Power supply / maximum power consumption 100 - 240V~, 50/60Hz, 2.5 - 1.
Index A Error number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Every Division . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23 Administration . . . . . . . . . . . . . . . . . . . . . . . . . 2-6, 2-31 Arranger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-16 Auto-Control Stacking Tray. . . . . . . . . . . . . . . . 1-4, 1-16 F B Basic Printing Operation . . . . . . . . . . . . . . . . . . . . 1-18 Beep Sound -Error . . . . . . . . . . . . . .
List of Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Location for Installation . . . . . . . . . . . . . . . . . . . . . . iv, vi M Magenta (M) Ink Cartridge . . . . . . . . . . . . . . . . . . . . 1-2 Main Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2, 1-5 Main Power Switch . . . . . . . . . . . . . . . . . . . . . 1-4, 1-10 Mainrtenance Door . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Maintenance Call. . . . . . . . . . . . . . . . . . . . . . .
Usable Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 WAKE-UP key . . . . . . . . . . . . . . . . . . . . . . . . . 1-5, 1-10 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 V Vent Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Y Yellow (Y) Ink Cartridge . . . . . . . . . . . . . . . . . . 1-2, 3-19 W Waiting Time . . . . . . . . . . . . . . . . . . . . . . . . . .
