TABLE OF CONTENTS INTRODUCTION TO NOVA LEVELS OF NOVA IT INSTALLATION & NORMAL LEVEL INSTALLATION & OPERATION Register Transmit Addresses in Recover... tron T COMMUNICATION TE rer 8 Formal Operation... ein tenets 10 ADVANCED LEVEL INSTALLATION & OPERATION... Advanced Level Installation Preparations Dieresis Transmitter Addresses in Receiver. To Erase an Address from Receiver. Communication Normal Mode. Event Retrieval from Memory. APPLICATION QUESTIONS & ANSWERS. SPECIFICATIONS...
Draft 2 INTRODUCTION TO NOVA 11 The NOVA IE has been designed for quick. sacs installation in either of two levels. The Normal level 15 adopted by most users. The Advanced level of consultation gives additional facilities for locating the source of an alarm For more information, contact the CORONET branch office nearest to vou, See the back cover of this manual NOVA IT Features “ It processes radio signals from up to 16 remote transmitters.
Draft LEVELS OF NOVA I INSTALLATION & OPERATION The NOVA 11 receiver provides two levels of security system installation and opera non: > tn the Normal Installation Setup. the NOVA 13 display gives a momentary indication of the reporting transmitter and the event (alarm, tow battery. or tamper). Input conditioning is completely handled by the control panel » In the Advanced Installation Sep. the NOVA 11 receiver assumes some of the functions of a control pan.
Figure I: Circuit Board. Schematic ant EVENT sW2 .
‘NORMAL LEVEL INSTALLATION & OPERATION (Continued) v v Remove the cover by twisting a screwdriver in the slots along the upper or lower edge of the receiver. Mount the NOVA 17 -receiver near the control panel 3 Connect the antenna to the lef terminal of TB4. > Se tall positions on dip switches SWI and SW. to OFF severs ase pushed DOWNY Wire the NOVA IT to the control panel a5 shown in Figure 2 Register Transmitter Addresses in Receiver ACTION RESPONSE Sex SWI position 7 to ON All LED's blink.
Draft Table I: Summary Instructions for Making Transmitters Send a WRITE Transmission: ‘NOVA-20 & NOVA-30 Set jumpers ta WRITE Mode. then press Tamper Switch for over 3 seconds. NOVA-36 ‘Press push button on internal transmitter board for ever 3 seconds. NOVA-30. $1. Press push button for aver 3 seconds NOVA-T | Disconnect and reconnect battery Communication Test Mount transmitters in the intended locations. then test communications as shown below.
"Draft 2 Normal Operation >» Set SWI positions 7 and § to OFF. Replace the cover 5 Reception of 2 signal from a transmitter will cause the corresponding green zone and transmitter LED's 10 blink. together with a red event LED which indicates the type of Transmission: Alas, Tamper.
ADVANCED LEVEL INSTALLATION & OPERATION The dip switch positions and supervision jumper are described in Table 2 and Table 3 below Table 2: Configuration Ipswich SW1 (8 Positions) Position Description Comments 1 Momentary Display, Latched Display. OFF All signals are momentarily displaced by zone. transmitter. and event ON: nails that cause an output are latched and displaced Zone output polar ned. OFF Zone outputs are Normally C. ON: Zane but pus are Normally Open.
Position Description Comments 456 Transmitter Configuration Setup Used in WRITE MODE Boston + SUPERVISION. Set ON for supervised transmitters (NOVA 20. 30, 70, 90). Set OFF for unsupervised transmitters (NOVA 50.31.52. 611. Position 3 DELAY. When ON. an alarm signal within 30 seconds of arm mg will br ignored: output due (0 an alarm signal received more than 30 seconds after arming will he delayed by 30 seconds and canceled if pane disarmed during ths period Position 6 NOT 24 HOURS When ON.
Draft? Table 3: Output Dip switch SW2 (4 Positions) and Jumper JP1 Determines which TROUBLE signals produce an output at the TROUBLE terminals. The TROUBLE output contacts are Normally Closed SW2 Position TROUBLE Output wheat set ON Low Battery i Tamper — from transmitter (NOVA 20 or NOVA 96. or from NOVA 1V receiver.
SPECIFICATIONS Operating Voltage and Current 1G 15 Side, $0 mA Receiver Typ SA / Stabilized Supernumerary Outputs. 2 Alarm relay outputs ius | trouble relay output Maximum number of transmitters 16 — maximum 4 per zone Transmitter Addresses Over 16 million Frequency Options 318 MHz FCC and IC Approved 18 MHz DT3 Approved 433.92 M «t European Standard Quip Comas Vdc maximum Dimensions Width. 145 mm (3.7 in} Height: 90 rm (3.54 1m.) Depth: 42 mm (1.63 in} Weight 2007.07 02) Temperature Range Ge 50°C.
Draft CAUTION NOTICE This device complies with U.S. FCC PART 15 and with RS-210 of Industry Canada, Operation is subject to the following two conditions: > This device may cause Interference. and This device must accept any Interference. including Interference that may cause undesired operations of the device. Changes or modifications not expressly approved by CORONET may void the user's authority 10 operate this equipment.
Draft 2 CORONET LIMITED WARRANTY Rookies Electrostatics. Lid. and its subsidiaries and affiliates Seller”) warrants its products to be free fro: defects 1 materials and workmanship under normal use for 18 months from the date of production.