User's Manual

ManualsBrandsRis ManualsElectronicsRISCO 2-WAY RF MODULE

Page 1

Introduction

RISCO Group's 2-Way Wireless I/O & X10 Module is an extension module enabling wired

devices to be connected to the Agility Wireless system.

The Wireless I/O Module supports 4 hardwired zones, 4 outputs and controls up to 16 X10

devices.

Each output or X10 device can be operated in a response to a wide variety of system events.

For detailed information regarding the programming options of the Wireless I/O Module

refer to the installation manuals of the Agility.

Main Features

Bi-directional wireless communication

2 Relay Outputs (3Amp)

2 Transistor Outputs (500 mA)

4 Inputs (NO, NC, EOL)

Fully supervised

Dual tamper protection (Box & Wall)

X10 adapter, up to 16 X10 devices

Wireless I/O Module - Ma in Componen ts

1. RF Module

2. Input Terminals

3. Relay Output Terminals

4. Transistor Output terminals

5. AC Power terminals

(parallel connection to J2)

6. Back/Wall tamper (not visible)

7. J2 Power socket

8. 3 LED indication

9. RJ11 connector (X10 connection)

10. Box tamper switch

11. Battery holders

RF Module

21 3 4 5

IN1 GND IN2 IN3 GND IN4 NO1 C1 NC1 NO2 C2 NC2 VO3 GND VO4

V11 V12

Figure 1: Wireless I/O Module Main

Components

Summary of content (8 pages)

PAGE 1
Introduction RISCO Group's 2-Way Wireless I/O & X10 Module is an extension module enabling wired devices to be connected to the Agility Wireless system. The Wireless I/O Module supports 4 hardwired zones, 4 outputs and controls up to 16 X10 devices. Each output or X10 device can be operated in a response to a wide variety of system events. For detailed information regarding the programming options of the Wireless I/O Module refer to the installation manuals of the Agility.
PAGE 2
LED Indications LED (Red)= (Yellow) State Power Description On AC and batteries OK Flashing AC trouble or Low battery (below 3.1 VDC) Off Power not present On X10 Connected to the Wireless I/O Module Off X10 Disconnected On The I/O expander is communicating with the Agility Off No communication is taking place X10 Communication (Green) Mounting the Wireless I/O Module Select a mounting location near an AC power supply in proximity to the Agility main panel 1.
PAGE 3
. Mount the receiver on the wall using the installation holes (3, Figure 4) and reinstall the circuit board. Make sure that that you hear a "click" when attaching the tamper spring to the wall. UO1 Z3 3 COM Z3 4 Z35 COM Z36 N O C NC NO UO2 C NC UO3 C OM UO4 3 AC 1 2 = 1 = Figure 3: Circuit Board Removal 4. Figure 4: Knockouts and Installation Holes Connect the power source wire plug to the J2 power jack on the PCB or to the AC terminals on the PCB. The polarity is not important.
PAGE 4
Wiring the Wireless I/O module Inputs wiring The Agility supports 4 hardwire zones (defined in the Agility system as zones 33-36) that can be defined as Normally Open, Normally Closed or End of Line Zones. The following diagram illustrates the various zone connections: NORMALLY CLOSED ZONE CONFIGURATION Z NORMALLY OPEN ZONE CONFIGURATION COM Z COM END OF LINE ZONE (N.C CONTACT) END OF LINE ZONE (N.O CONTACT) Z Z COM COM 2.2 K 2 .
PAGE 5
To wire Transistor Outputs (UO3-UO4) Connect the positive connection of the device to to the GND (-) UO3 or UO4 (+) and the negative connection terminals. UO3 COM X10 Connection UO4 EXTERNAL POWER The wireless I/O expander enables the Agility to control X10 devices. The I/O expander converts the information sent from the programmable utility output into the X10 protocol. Up to sixteen X10 devices can be activated. These are recognized in the system as outputs 5 to 20.
PAGE 6
Diagnostics You can perform diagnostic tests and check the status of the Inputs, Outputs connected to the Wireless I/O Module and the communication between the module and the Agility. The diagnostics can be performed locally from a keypad or remotely from the Configuration Software. Technical Specifications Electrical Characteristics Power Supply 9VAC, 0.5A minimum Current Consumption (Minimum / Maximum) 20 mA minimum / 150 mA maximum Backup Batteries 3 x size AA NiMH cylindrical cell 1.
PAGE 7
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 8
Contacting RISCO Group RISCO Group is committed to customer service and product support. You can contact us through our website www.riscogroup.com or as follows: United Kingdom USA Tel:+44-161-655-5500 Tel:+305-592-3820 sales@riscogroup.co.uk sales@riscogroupusa.com technical@riscogroup.co.uk support@riscogroupusa.com Italy Brazil Tel: +39-02-66590054 Tel:+55-11-3661-8767 info@riscogroup.it sales-br@riscogroup.com support@riscogroup.it support-br@riscogroup.