Auxin The Aux In stereo RCA connectors allow you to mix an external sound source (such as a CD player, MP3 player or computer output) with the piano's internal sounds, for playback through the pianos built-in speakers or headphone outputs. The Aux In signal level can be adjusted using the Input Level knob.
Ulcer & Functions The Voice Select buttons are used together with the Bank button to change the currently selected voice. Under the Voice Select buttons are two rows of voice names (a top row and a bottom row). When the Bank button is off (not lit), the voice select buttons may be used to activate any of the voices listed on the top row (Bank A). When the Bank button is lit, voices from the bottom row (Bank B) may be selected.
Split Mode In Split Mode, the keyboard is divided into two parts, with each part playing a different sound. This allows you to play two different instruments, for example, bass with your left hand and Plano with your right hand. In Split Mode, the Split Voice will play on all keys to the left of, and including the Split Point (explained on the next page}. The Main Voice will play on all keys to the right of the Split Point. Use Split{left hand) Mode Press the [SPLIT] button.
change the Main(right hand) Voice Press the [SPLIT] button then press a voice select button. WUT be CROATIAN E.PSND 1 BRIGHT BANG PORNO EEE CHURCH URBAN aa RHOS was PAD 8 change the Split(left hand) Point Press and hold the [SPLIT] button while pressing the highest note to be included in the Split zone the highest note to be played with the left hand voice).
Turn the [DATA CONTROL] knob to select a volume setting between 0 and 127. Bean Lane 8 Qx N Tempe la@ Ualzlz@ \ BATS iit Press the [SPLIT] button to turn Split Mode back on. Bia Plane Patagonia Upload Turn off Split(left hand) Mode Press the [SPLIT] button to turn off Split Mode. “ Grainy Lane 7 Tues lag ods lem ap The default values for Split Mode are: Default Split Point: F#2 Default Split Voice: Upright Bass NOTE The Main Voice {right hand voice} will transmit on the selected Main MIDI Transmit Channel.
Layer Mode In Layer Mode, this piano will play two voices simultaneously on each key. Turn on Layer Mode Press the [LAYER] button. The LCD's top line will show the Main Voice (first) and the Layer Voice (second). The bottom line will show the tempo and the Layer Voice volume. Bed Broke fan Forensic Lain sg NOTE ( That polyphony may be reduced while Layer Mode is in use. ] Change the Main Voice Press the Voice Select button. han he L.
Adjust the Volume of the Aver Voice Use the [DATA CONTROL] knob to adjust the volume. Press the [LAYER] button to turn off Layer Mode. Use the Data Control knob to adjust the Main Voice volume. NOTE Nigerien The Main Voice will be transmitted on the selected Main MIDI Transmit Channel. The Layer Voice will be played on the selected Main MIDI Transmit Channel +2. For information on setting the Main MIDI Transmit Channel, please see the “MIDI Channel” : MIDI Functions.
Using Split and Layer Modes Together When Split and Layer Modes are both enabled, Layer Mode will take priority, so the Data Control knob well be automatically assigned to control the volume level for the Layer Voice. If Layer Mode and Split Mode are both active, the Layer Voice will be added only to the Main Voice, not to the Split Voice. In other words, playing to the right of the Split Point will sound the Main and Layer Voices. Playing to the left of the Split Point will sound only the Split Voice.
Use the [DATA CONTROL] knob to adjust the Main Voice volume. Yeah Ue bias e Layer Mode. Transpose Button The Transpose Up and Down buttons are used to increase or decrease the keyboard's transpose value, up to 12 semi-tones (one octave) up or down. Use the Transpose Function ‘Each time you press the Transpose Up button, the pitch is raised by one semi-tone. In the same way, the Transpose Down button is used to lower the pitch in semi-tone increments.
Each time you press the Transpose Up button, the pitch is raised by one semi-tone. In the same way, the Transpose Down button is used to lower the pitch in semi-tone increments. Once you have changed the Transpose setting, the LCD will show a positive or negative value to the right of the voice name: & ox Ea Grand Plans sas pre Itemize Vacuole NOTE Changes to the Transpose setting are not remembered after a power cycle. The setting will be back at its default value of zero at power-up.
With Octave Shift Edit Mode enabled, press the [Transpose Up and Down buttons at the same time. C8 Denotative: an NOTE Changes to the Octave Shift setting are not remembered after a power cycle. The setting will be back at its default value of zero at power-up. Master Tune Although piano never actually slips out of tune, the Master Tuning function can be helpful when playing along with another instrument that may be tuned slightly higher or lower than standard pitch.
Touch Select Mode The Touch Sensitivity setting, sometimes referred to as the velocity curve, lets you decide how the pressure with which you hit a key determines the volume at which the note plays. piano provides you with three different sensitivity options: Normal is the default setting, and is designed to be useful for most players with an “average” touch people who play with an average amount of force). Low is a sensitivity setting that generates lower velocity values for the same force.
As you turn the [DATA CONTROL] knee, the LCD will scroll through the available Touch settings. (The “NORMAL” Touch setting is shown in the example below). @, RATS CONTRA NOTE Pressing the Transpose up and down buttons together while in Touch Select Mode will reset the Touch function back to its default value of Normal. Ti h Sensitive Fix: £1 Press the Touch button. The blue LED will turn off. Genes Plans Terms lag Vols lag ou.
Reverb Effect The built-in digital Reverb can be used for adding a natural-sounding room ambiance to any of the 16 voices built into piano. Apply Reverb to a Vole Press the [REVERB] button. The button will illuminate, and you will hear the Reverb effect when you play the currently selected voice. Begin 1 —_ or Trans To turn Reverb off, press the [REVERB] button again. The button will go dark to indicate that Reverb is off.
Change the Reverb Type While holding the [REVERB] button, use the [TRANSPOSE] buttons to select a Reverb Type. The LCD will show the current Reverb Depth and Type. Once you have selected the desired Reverb Type, let go of the Reverb button, and resume playing piano.
Adjust the Chorus Depth While holding the [CHORUS] button, turn the [DATA CONTROL] knob to adjust the Chorus Depth setting. The LCD will show the current Chorus Depth and Type seimbDeprky Bad Once you have the desired amount of Chorus, let go of the Chorus button, and resume playing piano. NOTE If you prefer, you may use the Tempo Up/Down buttons instead of the Data Control knob to change the Chorus Depth (while holding down the Chorus button).
Metronome The piano features a build-in metronome which you can use to practice your timing with. To activate it, simply press the METRONOME button. You can set both volume, tempo and time signature for the metronome. The following describes how to adjust each of those functions. metronome's Volume While holding down the [METRONOME] button, turn the [DATA CONTROL] knob clockwise to increase volume, or counterclockwise to decrease volume. The LCD will show the current Metronome Volume level.
Time Signature The metronome can support the following time signatures: 2/2, 2/4, 3/4, 4/4, 5/4, 6/8, 7/8, 9/8, 12/8 Change the Metronome's Time Signature Press the [DEMO] and [METRONOME] buttons at the same time to enter Time Signature Edit Mode. The top line of the LCD will show: Time Sig: 4/4 Tim 249 did Use the [TRANSPOSE] Up or Down button to change the Time Signature. You step through the time signatures in the following order: 2/2, 1/4, 2/4, 3/4, 4/4, 5/4, 9/8, 12/8.
ETA TTT The Song Recorder (or sequencer) built into piano can record two individual tracks, allowing you to record one part and then play and record a second complementary part while the first part plays back. Record a Track Track 1.Held down the [PLAY/RECORD] button , then press the [TRACK] button, the tight of the [TRACKLESS] button will flash and the light of the [PLAY/RECORD] button will turn on. SLAVE. J RECORD ~~ LEFT 2.Play the music to start recording. ATTAR 3.
2.Play the music to start recording. Lg] 3.Press the [PLAY/RECORD] button again to end off the recording. NOTE If the TRACK 1 has data recorded, the indicator will light and it will play when the record is started. You can press the [TRACK 1/LEFT] button to mute it, then the indicator will be unlighted. Play The Recording Press the [PLAY/RECORD] to play the local recording. During song playback you can select which track you wish to hear by press the [TRACK [CARTWRIGHT] button. RACK TRASH.