97.0 mm 97.0 mm For additional help, visit: ring.com/help Video Doorbell User Manual Or give us a call: US 1 800 656 1918 Canada 1 855 300 7289 AU 1 300 205 983 135.0 mm NZ +64 9 887 9871 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty Ring and all related logos are trademarks of 6ACS9202M.02G 6ACS9202M.02G-CS-9202_WT1_US/ANZ_Manual V2.
Download the Ring app. The Ring app walks you through setting up and managing your Video Doorbell. Search for “Ring” in one of the app stores below, or visit ring.com/app Charge your Video Doorbell. Plug it into a USB power source with the included cable. Once the light ring is fully lit, it’s ready to use. Grab your wifi password. You’ll need it for the next step, so write it down below. Set up your Video Doorbell near your wifi router. In the Ring app, select Set Up a Device. Try it out.
Select an install location. For optimal performance, install your Video Doorbell four feet above the ground. If you’re connecting to existing doorbell wiring that’s higher than four feet and want to angle your Video Doorbell down for a better view, you can purchase a Wedge Kit here: ring.com/accessories Camera field of view Motion detection range 4 feet (48 inches) Ring_PACK_DoorRVD1_G2_UserManual_v5.
Remove your existing doorbell. Mark the screw holes. Then, remove your existing doorbell button from the wall and disconnect the wires. Install the anchors. (optional) On stucco, brick, or concrete, use the provided bit to drill holes in your wall, then insert the anchors. (If you’re installing on wood or siding, you can skip this step.) Use the bracket as a template to mark the four corner holes. The recommended install height is 4 feet above the ground.
Install the mounting bracket. (continued) If you’re wiring your Video Doorbell, feed your doorbell wires through the hole in the mounting bracket first. Connect the wires. (optional) Connect your doorbell wires to the screws on the rear of your Video Doorbell. It doesn’t matter which wire connects to each screw. Drive the screws into your wall (or into the anchors, if installed) until they are flush with the mounting bracket.
Attach your Video Doorbell to the mounting bracket. Hook the slot on the rear of your Video Doorbell onto the tab near the top of the mounting bracket. Secure your Video Doorbell. Use the star-shaped end of the included screwdriver to drive the two security screws into the bottom of your Video Doorbell. Your Video Doorbell is now ready to use. If you wired in your Video Doorbell, you can now restore power at the breaker. Then, let the Doorbell pivot down to sit flush on its bracket.
1523 26th St. Santa Monica, CA 90404 IMPORTANT PRODUCT INFORMATION SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. Your device has a water resistance rating of IPx4 and has been tested to withstand water splashes in all directions from an oscillating spray. However, your device is not intended for underwater use.
RENSEIGNEMENTS IMPORTANTS CONCERNANT LE PRODUIT CONSIGNES DE SÉCURITÉ : LE NON-RESPECT DES PRÉSENTES CONSIGNES DE SÉCURITÉ POURRAIT CAUSER UN INCENDIE, UNE DÉCHARGE ÉLECTRIQUE OU UNE AUTRE FORME DE BLESSURE OU DE DOMMAGE. Votre appareil a une cote de résistance à l’eau d’IPx4 et a été testé pour résister aux éclaboussures d’eau dans toutes les directions d’un vaporisateur oscillant. Votre appareil n’est toutefois pas conçu pour un usage sous l’eau.
For Consumers in Australia Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.