. In-app Setup 2. Physical Installation 3. Features 4.
1. In-app Setup Welcome Congratulations on your new Ring Video Doorbell. We hope your Ring Doorbell brings you an increased sense of security and convenience, as well as the joy that comes from being able to connect with visitors when you’re not home. Hi, We’ve included all the tools you need, so setting it up by yourself should be a breeze. If you run into any problems, my colleagues and I can help. Just give us a call. 4.
2. Physical Installation 3. Features 3. Features 4. Troubleshooting 2. Physical Installation 1. In-app Setup 1. S et up your Ring Video Doorbell in the Ring app. 1. In-app Setup Contents 4.
1. In-app Setup The small light on top will glow green once fully charged. Insert the battery After charging, insert the battery in the bottom of your Ring Doorbell until it clicks into place. 2. Physical Installation 2. Physical Installation First, fully charge the battery by plugging it into a power source using the provided orange cable. 1. In-app Setup Charge the provided battery 3. Features 3. Features 4. Troubleshooting 6 4.
1. In-app Setup The Ring app will walk you through setting up and managing your Ring Doorbell. 2. Physical Installation Set up your Ring Doorbell indoors near your router In the Ring app, select Set Up a Device. When prompted, select Ring Video Doorbell and follow the in-app instructions. 2. Physical Installation Search for “Ring” in one of the app stores below, or visit: ring.com/app. 1.
1. In-app Setup Smile, you’re on camera! 2. Install your Ring Video Doorbell on the wall. 2. Physical Installation 2. Physical Installation After setup, push the button on the front of your Ring Doorbell to see video from the camera in the Ring app. 1. In-app Setup Try it out! 3. Features 3. Features 4. Troubleshooting 4. Troubleshooting Next, repeat this test where you will install your Ring Doorbell. Everything look good? Continue to the next section.
1. In-app Setup 2. Physical Installation 3. Features Install your Ring Doorbell four feet off the ground for optimal performance. If you’re connecting to existing doorbell wiring that’s higher than four feet, thus limiting where you can install Ring Doorbell, use the provided wedge mount to angle your Ring Doorbell down. Camera field of view 3. Features If wiring your Ring Doorbell to an existing doorbell, a transformer with a voltage of 8–24VAC is required.
2. Physical Installation Install the diode (optional) If installing on stucco, brick, or concrete, mark 4 drill holes. Use the provided bit to drill holes in your wall and insert the anchors. If you’re wiring your Ring Doorbell to a digital doorbell – you’ll know it’s digital if it plays a melody – then install the included diode. 2. Physical Installation Install anchors (optional) 1. In-app Setup 1.
Connect the Wires (optional) Connect the wires coming out of your wall to the screws on the bracket. 2. Physical Installation Attach the wire extensions (optional) If you have trouble connecting the wires coming out of your wall to the back of your Ring Doorbell, use the provided wire extensions and wire nuts. 2. Physical Installation Either wire can connect to either screw. The order doesn’t matter. Steps for wiring to an existing doorbell 1. In-app Setup 1.
1. In-app Setup 2. Physical Installation Install the faceplate Place one of the provided faceplates on your Ring Doorbell by slotting it in at the top and clicking it into place. 2. Physical Installation Feed all the wires (and the wire nuts, if you used them) into your wall and secure your Ring Doorbell on the wall using four screws. 1. In-app Setup Screw it in 3. Features 3. Features 4. Troubleshooting 4.
1. In-app Setup 2. Physical Installation 3. Check out all the exciting features. 2. Physical Installation Lastly, use one of the provided security screws and the starshaped end of the screwdriver bit to secure the faceplate. 1. In-app Setup Secure with a security screw 3. Features 3. Features 4. Troubleshooting 4.
1. In-app Setup 2. Physical Installation 4. Troubleshooting Device Health If you ever run into a problem with your Ring Doorbell, visit Device Health to diagnose the issue. Event History View a log of all the events captured by your Ring Doorbell in Event History. 4. Troubleshooting Motion Alerts are notifications you receive when movement is detected within your Motion Zones. Motion Settings Select Motion Settings to enable and customize your motion detection settings. 3. Features 3.
1. In-app Setup When someone is at your door, you can access these features: This optional feature saves recordings of every event your Ring Doorbell captures. 2. Physical Installation 2. Physical Installation Ring Video Recording 1. In-app Setup Answering your door 3. Features Microphone – Mute or unmute your mic. Speaker – Mute or unmute audio in the app. You can access these events on any device running the Ring app or by logging into your account at: ring.com/activity 3.
1. In-app Setup The front light on your Ring Doorbell uses patterns to communicate messages. 2. Physical Installation 3. Features Powered White Solid Front Button Pushed Blue Spinning Ring Speaker Enabled Blue Solid Updating Software White Flashing The Updating Software pattern will only ever appear directly after setup. Any other time that your Ring Doorbell updates, it will do so secrectly, late at night. 26 Here are some answers… 4. Troubleshooting 4. Troubleshooting White Spinning 3.
1. In-app Setup I’m having trouble completing the in-app setup When the in-app setup fails, look at the front of your Ring Doorbell. The light indicates the issue. 2. Physical Installation Top Flashing White means your Wi-Fi password was entered incorrectly. Select your Wi-Fi network in your phone settings, select the option to forget it, then reconnect to it again to confirm that you’re using the correct password during setup. 4. Troubleshooting 3.
1. In-app Setup Why isn’t my internal doorbell ringing properly when someone presses the button on my Ring? Make sure the circular light on the front of your Ring is glowing white to confirm that it’s wired correctly. 2. Physical Installation If your internal doorbell is digital (which means it produces a synthesized melody), make sure you installed the provided diode. If you have installed the diode, it may be installed backwards.
FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.