90mm 120mm Transformer Smart Lighting Landscape_Transformer_Manual.
For your safety... WARNING - Risk of electric shock. Do not mount power supply or luminaires within 10 feet (3.0 meters) of a pool, spa, or fountain. CAUTION: For use only on a branch circuit protected by a Class A type Ground Fault Circuit Interrupter (GFCI). When used outdoors, install only to a covered Class A GFCI protected receptacle that is weatherproof with the power unit connected to the receptacle. If one is not provided, contact a qualified electrician for proper installation.
1. S et up your Transformer. Download the Ring app. The app walks you through setting up and managing your Ring Transformer. Download it on your iOS or Android device. 4 Landscape_Transformer_Manual.indd 5 Set up your Ring Bridge. The Bridge connects your Ring Transformer to the Ring app and other compatible Ring devices. To set up your Bridge, follow the instructions in the Ring app or Bridge user manual.
Choose a location. Insert the top screws. You’ll have to plug in your Transformer, so the best place for it is near an outlet (make sure it’s a covered, weatherproof Class A GFCI protected outlet). Drive the top screws first, leaving 1/8” of space between the mounting surface and screw heads. 1/8” Once you’ve decided on a spot, use the included mounting template to mark the screw holes. To avoid damage to your Transformer, make sure the bottom screw is at least 1 foot above the ground.
2. Install lights and wiring. Your Transformer doesn’t come with low voltage cable, so you’ll have to buy some online or at a home improvement store. This chart might help. Ensure the total fixture wattage does not exceed the maximum wattage load of the Transformer. To get the total wattage, add up the wattage of each fixture (example: 10 fixtures at 5W each is 50W total wattage). 8 Landscape_Transformer_Manual.indd 9 Total Light Wattage Choose a cable.
Place light fixtures. Connect cable to Transformer. If you’re installing a new system, decide where you would like to place your lights (not included), and arrange them in the desired locations. Split and strip the cable. Open the Transformer door. Hold it open to access the terminals. Flip open the terminals, and feed one end of the cable through the rubber grommet into the Common terminal (left), and the other into either the 12V (center) or 15V terminal (right) based on the cable wattage you chose.
Run cable to fixtures. Starting at the Transformer, run the cable to each light fixture, leaving about 12” of cable after the last fixture. Leave a little extra cable at each fixture in case you have to adjust their location. Connect the wires. Secure the light fixtures to the cable according to the fixture manufacturer’s instructions. Plug the Transformer into the power outlet. Your Transformer must be connected to a covered, weatherproof GFCI protected receptacle.
Bury wiring cable. Dig a shallow trench (up to 6” deep) along the wiring route. Bury the wiring cable inside the trench. Connect your lighting to Ring. Press and hold the button on the front of your Transformer for 5 seconds. Once it starts flashing blue, it’s ready to pair with the Ring app. 14 Landscape_Transformer_Manual.indd 15 Complete Setup in the Ring app. In the app, tap Set Up a Device. Doorbells Security Cams When prompted, select Smart Lighting and follow the in-app instructions.
For additional help, visit: ring.com/help Or give us a call… US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit: ring.com/callus To review your warranty coverage, please visit www.ring.com/warranty. Patents: www.ring.com/patents © 2019 Ring LLC or its affiliates. Ring, Alexa, Always Home, and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Last updated: 01/17/19 Landscape_Transformer_Manual.
Warnings This device complies with part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.