User Guide Doorbell Wired
Included hardware. Find your doorbell chime. Bag Your Doorbell Wired is designed to replace an existing doorbell button, and gets its power from the doorbell system. Hardware A 3x Mounting Screws 3x Wall Anchors B 2x Security Screws C 1x Jumper Cable 2x Wire Extenders 2x Wire Nuts 2 Ring your existing doorbell and listen for the chime. If it rings, we know your existing doorbell system is working. Follow the sound to find your chime and make a mental note of the location.
Turn off power at the breaker. Grab the included Jumper Cable. This is essential to keeping you and your new Ring Doorbell safe. The Jumper Cable bypasses and disables your existing doorbell chime, and must be installed before you install your Ring Doorbell. If you’re not sure which breaker controls your doorbell chime, turn off the master breaker for your home, or contact an electrician. Your Doorbell Wired is compatible with doorbell systems supplying 8–24 volts AC, at 50 or 60Hz, 40VA max.
Remove the cover from your doorbell chime. After you’ve located your doorbell chime and turned off power at the breaker, remove the cover from your chime and set it aside for now. Loosen the “Front” and “Trans” terminal screws. Connect the Jumper Cable. Connect one end of the Jumper Cable to the “Front” terminal, and the other to the “Trans” terminal. It doesn’t matter which wire you connect to which terminal. Then re-tighten the terminal screws. Make sure to keep the existing doorbell wires in place.
Uninstall your existing doorbell button. Remove your doorbell from the wall. Disconnect the wires. Make sure they don’t fall back inside your wall so you can access them later. Mark the screw holes. Using your Ring Doorbell as a template, mark the location of the two mounting holes on your wall. Remove the faceplate. Grasp the bottom of the faceplate and pull to remove.
Install the anchors. (optional) On stucco, brick, or concrete, use a ¼" masonry bit to drill holes in your wall, then insert the included wall anchors. (If you’re installing on wood or siding, you can skip this step.) 10 Connect the doorbell wires. Loop one doorbell wire around each of the screw terminals on the rear of your Ring Doorbell then tighten the terminals to secure.
Screw in your Ring Doorbell. Restore power at the breaker. Mount your Ring Doorbell with the two included mounting screws. It may take a moment for your Ring Doorbell to power on. You’ll know it’s ready once it lights up and speaks to you. Be sure to feed any excess wiring back into the wall first. If you used the wire nuts, push them through the hole as well. DO NOT USE any screw other than the included long mounting screws when securing your Ring Doorbell.
Download the Ring App. Secure your Ring Doorbell. The Ring App walks you through setting up and managing your Ring Doorbell. Re-attach the faceplate, then use the included screwdriver to drive the small security screw into the bottom of your Ring Doorbell. Search for “Ring” in one of the app stores below, or visit ring.com/app DO NOT USE any screw other than the included short security screw when securing your Ring Doorbell. Set up your Ring Doorbell.
Review, share and download. Your new device comes with a free 30-day trial of Ring Protect video recording service. To continue your subscription and save your videos, please visit ring.com/protect-plans What is Ring Protect? Ring Protect is a subscription service that stores videos from your Ring devices. Why do I want it? Ring lets you interact with visitors and monitor your property in real time, while Ring Protect allows you review and share those videos anytime.
For additional help, visit ring.com/help Or give us a call: US 1 800 656 1918 Canada 1 855 300 7289 Worldwide +1 310 929 7085 For a list of all our customer support numbers, visit ring.com/callus For information on our warranty, theft © 2020 Ring LLC or its affiliates. protection, and Ring Protect Plans, see Ring and all related marks are trademarks ring.com/legal of Ring LLC or its affiliates.
xx-xxxxxx-xx
Quick Start 1. Open the Ring app and select Set Up Device. Then follow the in-app instructions. 2. Scan this code. This identifies your Ring device to make setup fast and easy. QR+FR For additional help, visit ring.
xx-xxxxxx-xx
Important Product Information Ring_INBOX_WSL_GrahamCracker_DoorbellWired_EN_v2d_GH 11/10/20 12:14 PM
IMPORTANT PRODUCT INFORMATION SAFETY INFORMATION: FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE. Your device can withstand outdoor use and has been tested to withstand water projected through a 6.3mm nozzle at a volume of 12.5 liters per minute and a pressure of 30 kPa at a distance of 3 meters for at least 3 minutes. However, your device is not intended for underwater use.
devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to www.amazon.com/ devicesupport. https://www.fcc.gov/oet/ea/fccid. Terms of Service and Warranty By purchasing or using the product, you agree to the Terms of Service found at ring.com/terms.
1523 26th St. Santa Monica, CA 90404 © 2020 Ring LLC or its affiliates. Ring and all related marks are trademarks of Ring LLC or its affiliates.