R inmei-P2 「Hardware Guide」回覧用原稿 Operating Instructions Hardware Guide 【申し送り事項】 ・Perseus-P2を流用しておりますが、ハード周りはR inmei-P1を流用し制作しております。 ・注釈の内訳は以下のとおりです。 関係区様への確認事項:赤色実線 修正個所、修正予定個所など:青色実線 保留個所:灰色実線 ・流用元からの主な変更点は以下の通りです。 カラーに関する表記の削除 ハード部のR inmei-P1からの移行 本体イラストの差替え ・イラストで一部未作成および修正の必要なものが残っています。 修正報告までに対応致しますので、ご了承ください。 ・LC D画面に関しましては、実機チェック時の状態に合わせています。 実機チェック時のF Wバージョン:V 0.21 For safe and correct use, be sure to read "Safety Information" before using the machine.
Draft 2011/08/30
TABLE OF CONTENTS Notice..................................................................................................................................................................4 Introduction.....................................................................................................................................................4 Important........................................................................................................................................................
. Configuration Ethernet Configuration.....................................................................................................................................43 Specifying an IP Address for IPv4 (No DHCP)..........................................................................................44 Receiving an IP Address for IPv4 Automatically (DHCP).........................................................................46 Specifying an IP Address for IPv6 (No DHCP).............................
Additional Troubleshooting...........................................................................................................................119 9. Removing Misfed Paper When Paper is Jammed.................................................................................................................................121 When "Internal Misfeed," "Misfeed: PprTray", "Misfeed: Tray 1", or "Misfeed: Tray 2" Appears....121 When "Misfeed: Bypass Tray" Appears.............................................
Notice Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. Do not copy or print any item for which reproduction is prohibited by law. Copying or printing the following items is generally prohibited by local law: bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses.
How to Read This Manual Symbols This manual uses the following symbols: Indicates points to pay attention to when using the machine, and explanations of likely causes of paper misfeeds, damage to originals, or loss of data. Be sure to read these explanations. Indicates supplementary explanations of the machine's functions, and instructions on resolving user errors. This symbol is located at the end of sections. It indicates where you can find further relevant information.
Ri nmei - P1に合わせて修正しました。 Model-Specific Information This section explains how you can identify the model type and region of your machine. This printer comes in two models that have different duplex functions. When describing procedures that are model-specific, this manual refers to the different printer models as Type 1 or Type 2. The following table describes the model types.
• Dimensions in this manual are given in two units of measure: metric and inch. If your machine is a Region A model, refer to the metric units. If your machine is a Region B model, refer to the inch units. rinmei-p2_com_hardware_guide_gb_00060047_eng.
Ri nmei - P1を流用しています。 Positions of labels WARNING and CAUTION This machine has labels for WARNING and CAUTION at the positions shown below. For safety, please follow the instructions and handle the machine as indicated. 1 2 3 4 CMC004 1 Do not incinerate toner or toner containers. Toner dust may cause flashback when exposed to an open flame. 2 Do not touch the parts a label indicates. The inside of the machine could be very hot. 3 Do not touch the parts a label indicates.
4 正規ラベルに差し 替えます。 The printer weighs approximately 12 kg (26.4 lb). When moving the printer, use the inset grips on both sides, and lift slowly. Power Switch Symbols The meanings of the symbols for the switches on this machine are as follows: • : POWER ON • : POWER OFF rinmei-p2_com_hardware_guide_gb_00060048_eng.
Manuals for This Printer Read this manual carefully before you use this printer. Refer to the manuals that are relevant to what you want to do with the printer. • Media differ according to manual. • The printed and electronic versions of a manual have the same contents. • Adobe® Acrobat® Reader®/Adobe Reader must be installed in order to view the manuals as PDF files. 初出の部分にRマーク追加しました。 • A Web browser must be installed in order to view the html manuals.
List of Option This section provides a list of option for this printer, and how it is referred to as in this manual. Option List Paper Feed Unit TK1080 Referred to as Paper feed unit • For details about the specifications of this option, see "Specifications". • p.139 "Specifications" rinmei-p2_com_hardware_guide_gb_00060051_eng.
CD- ROMに関する内容はすべて未確認です。 マニュアルCD構成仕様書が発行され次第、確認致しま す。 Operating Instructions This section explains how to use HTML format manuals. Reading the HTML Manuals on the CD-ROMs This section describes how to read the HTML manuals on the supplied manual CD-ROMs. 1. Insert the CD-ROM into the CD-ROM drive of your computer. 2. Select a language and a product, and then click [OK]. 3. Click [Read HTML manuals]. 4. Click the title of manual you want to read. The browser opens, and then the manual appears.
4. Install the HTML manuals following the on-screen instructions. 5. When the installation is complete, click [Finish]. 6. Click [Exit]. 7. Open the HTML manuals that you installed. When opening the manuals from an icon, double-click the manual icon on the desktop. When opening the manuals from the [Start] menu, point to [All Programs], and then [Product Name]. 8. Click the title of the manual you want to read. • You need administrator permissions to install the manuals.
14 rinmei-p2_com_hardware_guide_gb_00060052_eng.
1. Guide to the Printer This chapter explains the names and functions of the printer's components. P. 17まで、Ri nmei - P1を流用して おります。 1 Exterior: Front View 1 2 3 4 5 9 6 8 7 CMC006 1. Control Panel Contains keys for printer control and indicators that shows the printer status. 2. Stop Fences Raise this fence to prevent paper from falling off. 3. Output Tray Printed paper is output here. Up to 125 sheets of plain paper can be stacked here. 4.
1. Guide to the Printer Exterior: Rear View 1 1 2 5 4 3 CMC008 1. Ethernet Port Use a network interface cable to connect the printer to the network. 2. USB Port Use a USB cable to connect the printer to the host computer. 3. Rear Cover Open this cover to remove jammed paper or when printing on envelopes. 4. Tray 1 Rear cover Remove this cover when you load paper larger than A4 in the paper tray. 5. Power Socket For connecting the power cord to the printer.
Interior Interior 1 1 If a toner end indicator on the control panel lights up, から 修正しました。 CMC009 1. Print Cartridge If the following message appears on the control panel, replace the print cartridge. "Replace Toner:" • For details about the messages which appear on the screen to prompt you to replace the units, see p.103 "Error & Status Messages on the Control Panel". rinmei-p2_com_hardware_guide_gb_00060059_eng.
1. Guide to the Printer Control Panel 1 1 2 10 3 9 4 8 7 5 説明順はイラストに合わせて並 べ替えています。 6 CMC010 1. Display Displays current printer status and error message. You can set the display up with your hands. Adjust the angle of it to see clearly. LCDパネル引き起こしの説明を追加 しました。 CMC011 2. Scroll Keys Press to move the cursor in each direction, step by step. 3. [Escape] key Press this key to cancel an operation or to return to the previous display. 18 rinmei-p2_com_hardware_guide_gb_00060060_eng.
Control Panel 4. [OK] key Press this key to confirm settings and setting values, or move to the next menu level. 5. Data In Indicator Flashes when the printer is receiving data from a computer. The data indicator is lit if there is data to be printed. 1 6. Alert Indicator Lights up in red whenever printer error occurs. Use display to check the error. Flashes in yellow when toner is nearly empty. 7. Power Indicator Remains lit while the power is on. It is unlit when the power is off. 8.
1. Guide to the Printer 1 20 rinmei-p2_com_hardware_guide_gb_00060060_eng.
2. Installing the Printer and Options This chapter explains how to set up, configure the printer for operation, and install the optional paper feed unit for this printer. Installing the Printer 2 This section describes how to install the printer and perform settings after installation. Where to Put the Printer The printer's location should be carefully chosen because environmental conditions greatly affect its performance. • The supplied power cord is for use with this equipment only.
2. Installing the Printer and Options • Do not place vases, plant pots, cups, toiletries, medicines, small metal objects, or containers holding water or any other liquids, on or close to this machine. Fire or electric shock could result from spillage or if such objects or substances fall inside this machine. 2 • Keep the machine away from humidity and dust. Otherwise a fire or an electric shock might occur. • Do not place the machine on an unstable or tilted surface.
Installing the Printer • Keep the machine away from salt-bearing air and corrosive gases. Also, do not install the machine in places where chemical reactions are likely (laboratories, etc.), as doing so will cause the machine to malfunction.
2.
Installing the Printer • If the machine emits smoke or odours, or if it behaves unusually, you must turn off its power immediately. After turning off the power, be sure to disconnect the power cord plug from the wall outlet. Then contact your service representative and report the problem. Do not use the machine. Doing so could result in fire or electric shock. 2 • If metal objects, or water or other fluids fall inside this machine, you must turn off its power immediately.
2. Installing the Printer and Options • Do not crush or squeeze toner containers. Doing so can cause toner spillage, possibly resulting in dirtying of skin, clothing, and floor, and accidental ingestion. 2 • Store toner (new or used), toner containers, and components that have been in contact with toner out of reach of children. • If toner or used toner is inhaled, gargle with plenty of water and move into a fresh air environment. Consult a doctor if necessary.
Installing the Printer • Do not allow paper clips, staples, or other small metallic objects to fall inside the machine. • Keep the uncovered print cartridge away from direct sunlight. • Do not touch the print cartridge's photo conductor. 2 CMC013 Do not touch the ID chip on the side of the print cartridge. CMC014 1. Take out the printer from the box, and then remove the plastic bag. 2. Lift the printer by using the inset grips on both sides of the printer.
2. Installing the Printer and Options 3. Remove the protective materials attached on the printer's exterior. 2 CMC16 P1同様、背面2個 所にテープを追加 致します。 CMC007 The actual printer may come with protective materials attached in different positions. Make sure to check the printer's exterior for all protective materials, and remove them completely. 4. Push the side button to open the front cover, and then carefully lower it.
Installing the Printer 5. Remove the protective material attached inside the printer. 1 2 3 2 CMC018 6. Unpack the print cartridge. Then, place it on a flat surface, and remove the protection sheet. CMC019 Shake the print cartridge from side to side five or six times. CMC020 rinmei-p2_com_hardware_guide_gb_00060063_eng.
2. Installing the Printer and Options 7. Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in. Then push down on the cartridge until it clicks into place. 2 CMC021 8. Using both hands, carefully push up the front cover until it closes. CMC022 9. Carefully pull tray 1, and then pull out with both hands. CMC023 30 rinmei-p2_com_hardware_guide_gb_00060063_eng.
Installing the Printer 10. Remove the protective material attached inside the tray. 2 CMC024 11. Carefully push tray 1 straight into the printer. CMC025 12. Pull out and raise the stop fence. 2 1 CMC026 Turning the Power On Follow the procedure below to turn the power on. rinmei-p2_com_hardware_guide_gb_00060063_eng.
2. Installing the Printer and Options • Do not use any power sources other than those that match the specifications shown in this manual. Doing so could result in fire or electric shock. 2 • Do not use any frequencies other than those that match the specifications shown. Doing so could result in fire or electric shock. • Do not use multi-socket adaptors. Doing so could result in fire or electric shock. • Do not use extension cords. Doing so could result in fire or electric shock.
Installing the Printer • If this machine is not going to be used for several days or longer at a time, disconnect its power cord from the wall outlet. • When performing maintenance on the machine, always disconnect the power cord from the wall outlet. 2 • Make sure the power cable is plugged securely into the wall outlet. • Turn the power switch off when plugging and unplugging the power plug. • Do not turn off the power switch until initializing is completed. Doing so results in malfunction. 1.
2. Installing the Printer and Options • The machine may make a noise while initializing. This noise does not indicate a malfunction. Selecting the Display Language 2 Select a language using the procedure described here. The message for the selected language will appear on the display. If you want to use the display in English, the following procedures are unnecessary. • The default setting is English. 1. Press the [Menu] key. CMC034 2.
Installing the Printer 2. Press the [ ] or [ ] key to display [List/Test Print], and then press the [OK] key. Menu: List/Test Print 3. Press the [ ] or [ ] key to display [Config. Page], and then press the [OK] key. List/Test Print: Config. Page 2 The configuration page will be printed. 4. Press the [Menu] key to return to the initial screen. • If printing is not normal, check to see if an error message appears on the display. • If there is an error message, see p.
2. Installing the Printer and Options Installing Option This section describes how to install option. By installing option, you can improve the printer performance and have an expanded variety of features to use. For the specifications of each option, see p.139 "Specifications". 2 Attaching Paper Feed Unit • Touching the prongs of the power cable's plug with anything metallic constitutes a fire and electric shock hazard. • It is dangerous to handle the power cord plug with wet hands.
Installing Option 1. Check the package contains Paper Feed Unit. 2 CMC030 2. Turn off the printer's power switch, and then unplug the printer's power cord from the wall outlet. 3. Remove the adhesive tape from the optional paper feed unit. CMC024 4. Lift the printer using the inset grips on both sides of the printer. CMC032 rinmei-p2_com_hardware_guide_gb_00060069_eng.
2. Installing the Printer and Options 5. There are three upright pins on the optional paper feed unit. Align them with the holes on the underside of the printer, and then carefully lower the printer. 2 CMC033 6. After installing the option, print the configuration page to confirm the installation. • When moving the printer, remove the optional paper feed unit. • Before using the optional paper feed unit, you can make settings in the printer driver.
3. Connecting the Printer This chapter explains how to connect network and USB cables. Network Connection Follow the procedure below to connect the printer to the computer through the network. Prepare a hub, straight-through Ethernet cable, and any other necessary network devices before connecting the 10BASE-T or 100BASE-TX cable to the printer's Ethernet port. 3 • Connect only an approved network interface board to this printer.
3. Connecting the Printer • For details about network environment settings, see Software Guide. Reading the LED Lamps Ri nmei - P1に合わせました。 3 1 2 CMF062 1. Yellow: Lights up when 10BASE-T connection is properly established. Flashes when data is being transmitted. 2. Green: Lights up when 100BASE-TX connection is properly established. Flashes when data is being transmitted. 40 rinmei-p2_com_hardware_guide_gb_00060073_eng.
USB Connection USB Connection • For users outside the United States of America: properly shielded and grounded cables and connectors must be used for connections to a host computer (and/or peripheral) in order to meet emission limits. • For users in the United States of America: properly shielded and grounded cables and connectors must be used for connections to a host computer (and/or peripheral) in order to meet FCC emission limits. 3 • USB2.0 interface cable is not supplied.
3. Connecting the Printer 3 42 rinmei-p2_com_hardware_guide_gb_00060075_eng.
4. Configuration This chapter explains supported network connections and settings for the IP addresses. Ethernet Configuration If connecting the printer to a network using an Ethernet cable, set the necessary settings, depending on the network environment, on the control panel. Web Image Monitor can be used for the settings related to the IP address. • The following table shows the control panel settings and their default values. These items appear in the [Network Setting] under [Host Interface] menu.
4. Configuration 項目の並びを実機での表示順に合わせました。 Setting Name Value • IPv6: On • DHCP: Off • IP Ad. (DHCP): XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX: XXXX *1 If the DHCP setting is enabled, the IPv6 address obtained from a DHCP server is displayed. • Manual Address: • Manual Address: 0000:0000:0000 4 • Prefix Length: (0-128) 0 • Gateway Address: 0000:0000:0000: IPv6 Config. • Stateless Ad.
Ethernet Configuration 1. Press the [Menu] key. CMC034 2. Press the [ ] or [ ] key to display [Host Interface], and then press the [OK] key. Menu: Host Interface 4 3. Press the [ ] or [ ] key to display [Network Setting], and then press the [OK] key. Host Interface: Network Setting 4. Press the [ ] or [ ] key to display [IPv4 Config.], and then press the [OK] key. Network Setting: IPv4 Config. 5. Press the [ ] or [ ] key to display [DHCP], and then press the [OK] key. IPv4 Config.: DHCPv4 DHCPから修正 6.
4. Configuration 8. Press the [ ] or [ ] key to enter the address, and then press the [OK] key. IP Address: 0. 0. 0. 0 Press the [ ] or [ ] key to enter the left most entry field of the address. After entering the left field, press the [OK] key, and then you can enter the next field. After completing to enter in the all field, press the [OK] key. 9. Use this method to assign Subnet Mask and Gateway Address. 10. Press the [Menu] key. 11.
Ethernet Configuration 2. Press the [ ] or [ ] key to display [Host Interface], and then press the [OK] key. Menu: Host Interface 3. Press the [ ] or [ ] key to display [Network Setting], and then press the [OK] key. Host Interface: Network Setting 4. Press the [ ] or [ ] key to display [IPv4 Config.], and then press the [OK] key. Network Setting: IPv4 Config. 4 5. Press the [ ] or [ ] key to display [DHCP], and then press the [OK] key. IPv4 Config.: DHCPv4 DHCPから修正 6.
4. Configuration 1. Press the [Menu] key. CMC034 4 2. Press the [ ] or [ ] key to display [Host Interface], and then press the [OK] key. Menu: Host Interface 3. Press the [ ] or [ ] key to display [Network Setting], and then press the [OK] key. Host Interface: Network Setting 4. Press the [ ] or [ ] key to display [IPv6 Config.], and then press the [OK] key. Network Setting: IPv6 Config. 5. Press the [ ] or [ ] key to display [IPv6], and then press the [OK] key. IPv6 Config.: IPv6 6.
Ethernet Configuration 8. Press the [ ] or [ ] key to display [Off], and then press the [OK] key. DHCP Off 9. Press the [ ] or [ ] key to display [Manual Address], and then press the [OK] key. IPv6 Config.: Manual Address 10. Press the [ ] [ ] keys to display [Prefix Length], and then press the [OK] key. Manual Address: Prefix Length 4 11. Press the [ ] [ ] keys to enter the value, and then press the [OK] key. Prefix Length: (0 - 128) 0 12.
4. Configuration • Consult your network administrator for information about making network settings. 1. Press the [Menu] key. 4 CMC034 2. Press the [ ] or [ ] key to display [Host Interface], and then press the [OK] key. Menu: Host Interface 3. Press the [ ] or [ ] key to display [Network Setting], and then press the [OK] key. Host Interface: Network Setting 4. Press the [ ] or [ ] key to display [IPv6 Config.], and then press the [OK] key. Network Setting: IPv6 Config. 5.
Ethernet Configuration This operation makes the alert lamp blink. It indicates you need to restart the machine. You can operate the machine while the lamp is blinking. But the lamp does not go off until you restart the machine. 9. Press the [Menu] key. 10. If you are requested to restart the printer, turn off the printer, and then turn it back on. 11. Print a configuration page to confirm the settings made. • For details about printing the configuration page using control panel, see p.34 "Test Printing".
4. Configuration 1. Press the [Menu] key. CMC034 4 2. Press the [ ] or [ ] key to display [Host Interface], and then press the [OK] key. Menu: Host Interface 3. Press the [ ] or [ ] key to display [Network Setting], and then press the [OK] key. Host Interface: Network Setting 4. Press the [ ] or [ ] key to display [Ethernet Speed], and then press the [OK] key. Network Setting: Ethernet Speed 5. Press the [ ] or [ ] key to select the Ethernet speed, and then press the [OK] key. 6. Press the [Menu] key.
5. Paper and Other Media This chapter explains the paper sizes and types supported by this printer, and how to load paper into the paper trays. このセクションは仕様書「PRO2 Syst em Funct i onal Speci f i cat i on V0. 12̲20110704. pdf 」に合わせて修正しています。 各修正点における修正内容は、原則削除分を除いて省略しています。 Paper and Other Medias Supported by This Printer This section describes the type, size, and weight of paper that can be loaded in each tray. The capacity of each paper tray is also provided.
5. Paper and Other Media Tray 2 (option) Type Size Weight Capacity Thin Paper A4 60 to 105 g/m2 250 Thick Paper 1 Letter (81/2 " × 11 ") (16.0 to 28.0 lb.) (80 g/m2, 20 lb.) Plain Paper B5 JIS Recycled Paper A5 Color Paper Legal (81/2 " × 14 ") Preprinted Paper Half Letter (51/2" × 81/2") 少数点以下の桁 数を他と揃える ため. 0追加しま した。 Prepunched Paper Letterhead 5 Bypass tray Type Size Weight Thin Paper A4 52 to 162 g/m2 Thick Paper 1 B5 JIS (13.8 to 43.0 lb.
Paper and Other Medias Supported by This Printer Ri nmei - P1に合わせてNot eの内 容を修正しました。 • The number of sheets that can be printed in one minute may become lower than normal when printing on Legal size paper. 5 rinmei-p2_com_hardware_guide_gb_00060086_eng.
5. Paper and Other Media Paper Recommendations Loading Paper • When printing on OHP transparencies that have a print side, load them with the print side over on the bypass tray. Not taking this precaution may cause them to stick to the fusing unit and cause misfeeds. OHPの表のNet esに移動 • Do not use ink-jet printer paper because it may stick to the fusing unit and cause a paper misfeed.
Paper Recommendations Printer driver On the printer driver screen, click the [Paper] tab, and then select a paper type under [Paper Type:]. For details about the printer driver, see Help for the driver. Control Panel Press the [Menu] key, and then specify the paper type that you want to use by selecting a [Paper Type] at [Paper Input]. For details, see p.78 "Specifying a paper type for Tray 1 and Tray 2" and p.84 "Specifying a paper type for the bypass tray".
5. Paper and Other Media Thick Paper 1 Item Description Paper thickness 100 to 130 g/m2 (26.6 to 34.6 lb.) Supported paper tray Any input tray can be used. Duplex supported size A4, Legal (81/2 " × 14 "), Letter (81/2 " × 11 ") • Tray 2 only supports thick paper weighing 100 to 105 g/m2 (26.6 to 28.0 lb). Notes • Duplex printing is only possible with thick paper weighing 100 to 105 g/m2 (26.6 to 28.0 lb).
Paper Recommendations Recycled Paper Item Description 少数点以下の桁数を他と揃える ため. 0追加しました。 Paper thickness 75 to 90 g/m2 (20.0 to 24.0 lb.) Supported paper tray Any input tray can be used. Duplex supported size A4, Legal (81/2 " × 14 "), Letter (81/2 " × 11 ") • Tray 2 only supports paper weighing 60 to 64 g/m2, 16.0 to 17.0 lb.). Notes • If the paper thickness is outside the specified range, select [Thin Paper], [Thick Paper 1], or [Thick Paper 2].
5. Paper and Other Media Item Description Duplex supported size A4, Legal (81/2 " × 14 "), Letter (81/2 " × 11 ") Notes If the paper thickness is outside the specified range, select [Thin Paper], [Thick Paper 1], or [Thick Paper 2]. Letterhead Item 5 Description Paper thickness 75 to 90 g/m2 (20.0 to 24.0 lb.) Supported paper tray Any input tray can be used. Duplex supported size A4, Legal (81/2 " × 14 "), Letter (81/2 " × 11 ") • Tray 2 only supports paper weighing 60 to 64 g/m2, 16.0 to 17.
Paper Recommendations Item Description Supported paper tray Tray 1 and bypass tray Duplex supported size None Notes • The number of sheets that can be printed in one minute is approximately half that of plain paper. • When using 135 g/m2 (35.9 lb.) or heavier paper, prints may be output with strong curls. • When using 135 g/m2 (35.9 lb.) or heavier paper, take prints from the output tray frequently. • Paper thicker than 160 g/m2 cannot be printed onto.
5. Paper and Other Media Item Notes Description • When loading OHP transparencies, take care not to load them upside down. Doing so may cause a malfunction. • It is recommended to place one sheet at a time. • Make sure to fan OHP transparencies every time before printing. Leaving OHP transparencies loaded in the bypass tray may cause them to stick together and result in a misfeed. • If multiple OHP transparencies are fed at the same time, load them one by one.
Paper Recommendations CMC039 • Fan envelopes, and then align their edges before loading. 5 CMC040 • When fanning envelopes, make sure they are not stuck together. If they are stuck together, separate them. • When fanning envelopes, make sure the envelope flaps are not stuck together. If they are stuck together, separate them. • Before loading envelopes, flatten them out so that their curl does not exceed that shown in the illustration below.
5. Paper and Other Media 両面印刷対応はA4, Legal , Let t er だけなので、Not eを削 除しました。 CMC042 Paper Not Supported by This Printer Avoid using the following paper as they are not supported by this printer. 5 • Paper meant for an ink-jet printer • Bent, folded, or creased paper • Curled or twisted paper • Torn paper • Wrinkled paper • Damp paper • Paper that is dry enough to emit static electricity • Paper that has already been printed onto, except a preprinted letterhead.
Paper Recommendations Paper Storage Precautions Paper should always be stored properly. Improperly stored paper might result in poor print quality, paper jams, or printer damage. Recommendations are as follows: • Avoid storing paper in areas that are excessively cold, hot, humid, or dry. • Avoid exposing paper to direct sunlight. • Store on a flat surface. • Keep paper in its original packaging. Print Area The following diagrams show the areas of paper that the machine can print onto.
5. Paper and Other Media Envelope 3 1 2 Ri nmei - P1を流用してお ります。 3 4 4 CMC044 1. Print area 2. Feed direction 3. Approx. 4.2 mm (0.17 inches) 5 4. Approx. 4.2 mm (0.17 inches) • The print area may vary depending on the paper size, printer language and printer driver settings. • For better envelope printing, we recommend you set the right, left, top, and bottom print margins to at least 15 mm (0.59 inches) each. 66 rinmei-p2_com_hardware_guide_gb_00060087_eng.
Loading Paper Loading Paper This describes how to load paper into the paper tray and bypass tray. • Do not pull out the paper tray forcefully. If you do, the tray might fall and cause an injury. • When loading paper, take care not to trap or injure your fingers. P1同様、"levers"に修正致します。 (以降ページ、全て修正致します) Loading Paper in Tray 1 The following example explains loading procedure for the standard paper tray (Tray 1).
5. Paper and Other Media 2. Push the metal plate down until it clicks into place to lock. 削除しました。 Place the tray on a flat surface. 2. Pinch the clip on the side paper guide and slide it to match the standard size. CMC046 5 CMC047 When loading custom size paper, position the paper guide slightly wider than the actual paper size. 3. Pinch the end paper guide and slide it inward to match the standard size. CMC048 68 rinmei-p2_com_hardware_guide_gb_00060096_eng.
Loading Paper CMC049 When loading custom size paper, position the paper guide slightly wider than the actual paper size. 4. Load the new paper stack print side down. Make sure paper is not stacked higher than the upper limit marked inside the tray. 5 CMC050 Slide the guides inward, until they are flush against the paper's sides. Make sure the paper is not stacked higher than the projection on the side paper guides. CMC051 rinmei-p2_com_hardware_guide_gb_00060096_eng.
5. Paper and Other Media 5. Check there are no gaps between the paper and the paper guides; both side and end paper guides. CMC052 If there is a gap between the paper and the end paper guide, as in the example below, the paper might not feed in correctly. 5 CMC058 6. Carefully push Tray 1 straight into the printer. CMC053 To avoid paper jams, make sure the tray is securely inserted.
Loading Paper • For details about paper types supported by the printer, see p.56 "Paper Recommendations". • For details about the paper settings, see Software Guide. Loading paper longer than A4 This section explains how to load paper longer than A4 (297 mm) into the printer. • Make sure paper is not stacked above the limit mark inside the tray. Misfeeds might occur. • After loading paper in the tray, specify the paper type and size using the control panel to avoid printing problems.
5. Paper and Other Media 3. Release the extender locks on both sides of the tray, and then pull out the extender until it clicks. CMC055 Make sure the extender's inner surface and the scale are aligned. 5 CMC056 4. Lock the extender in the extended position. CMC057 72 rinmei-p2_com_hardware_guide_gb_00060096_eng.
Loading Paper 5. Pinch the clip on the side paper guide, and then slide it to match the standard size. CMC059 5 CMC047 6. Pinch the end paper guide and slide it inward to match the paper size. CMC060 rinmei-p2_com_hardware_guide_gb_00060096_eng.
5. Paper and Other Media CMC049 7. Load the new paper stack print side down. Make sure paper is not stacked higher than the upper limit marked inside the tray. 5 CMC069 Slide the guides inward until they are flush against the paper's sides. Make sure the paper is not stacked higher than the projection on the side paper guides. CMC051 74 rinmei-p2_com_hardware_guide_gb_00060096_eng.
Loading Paper 8. Check there are no gaps between the paper and the paper guides; both side and end paper guides. CMC062 If there is a gap between the paper and the end paper guide, as in the example below, the paper might not feed in correctly. 5 CMC063 9. Carefully push Tray 1 straight into the printer. CMC053 To avoid paper jams, make sure the tray is securely inserted. • To reinsert the extender, you might have to push it with moderate force.
5. Paper and Other Media • For details about paper types supported by the printer, see p.56 "Paper Recommendations". • For details about the paper settings, see Software Guide. Setting a paper size using the control panel To load paper whose size cannot be selected automatically, set the paper size on the control panel. Follow the procedure described below to set the paper size. 1. Press the [Menu] key. 5 CMC034 2. Press the [ ] or [ ] key to display [Paper Input], and then press the [OK] key.
Loading Paper Tray 1 Ppr Size: 8 1/2 x 11 6. Press the [Menu] key. • If the [Auto Continue] setting under [System] is enabled, the printer ignores the paper type and size settings and prints on whatever paper is loaded. Printing stops temporarily when the error is detected, and restarts automatically after about ten seconds using the settings made on the control panel.
5. Paper and Other Media 4. Press the [ ] or [ ] key to display [Tray 1], and then press the [OK] key. Paper Size: Tray 1 Paper Size Tr ay 1から修正 In this example, [Tray 1] is selected. 5. Press the [ ] or [ ] key to display [Custom Size], and then press the [OK] key. Tray 1 Ppr Size: Custom Size 6. Press the [ ] or [ ] key to select a unit, and then press the [OK] key. Custom Size: mm 7. Press the [ ] or [ ] key to enter the horizontal value, and then press the [OK] key. 5 Custom Size: Horiz. 216.
Loading Paper 1. Press the [Menu] key. CMC034 2. Press the [ ] or [ ] key to display [Paper Input], and then press the [OK] key. Menu: Paper Input 3. Press the [ ] or [ ] key to display [Paper Type], and then press the [OK] key. 5 Paper Input: Paper Type 4. Press the [ ] or [ ] key to select the paper tray, and then press the [OK] key. In this example, [Tray 1] is selected. Paper Type: Tray 1 5. Press the [ ] or [ ] key to select the paper type, and then press the [OK] key. Tray 1: Plain Paper 6.
• You cannot use the bypass tray to feed in paper that requires a specified printing position (such as preprinted paper). Use Tray 1 for such paper. 削除しました。 5. Paper and Other Media Loading Paper in the Bypass Tray • Before printing on paper other than envelopes, make sure that the fusing unit levers inside the front cover are pulled up. Leaving the levers lowered can cause print quality problems when printing on paper other than envelopes.
Loading Paper 2. Slide the side guides outward, then load paper with the print side up, and push in until it stops against the printer. CMC074 3. Adjust the side guides to the paper width. 5 CMC075 • After loading paper in the tray, specify the paper type and size using the control panel. Also, specify the printer driver's paper setting accordingly before printing. • For details about supported types of paper, see p.53 "Paper and Other Media". • For details about the paper settings, see p.
5. Paper and Other Media • If you set [Bypass Priority] to [Machine Setting] under [Paper Input], paper size settings made on the printer driver must match those made on the control panel. If they do not match, an error message appears and printing stops if [Auto Continue] is not set to [On] under [System]. 1. Press the [Menu] key. CMC034 5 2. Press the [ ] or [ ] key to display [Paper Input], and then press the [OK] key. Menu: Paper Input 3.
Loading Paper Specifying custom size paper for the bypass tray • When you specify a custom size paper and specify the bypass tray as the input tray on the printer driver, and perform printing with [Bypass Priority] set to [Any Custom S/T] under [Paper Input] on the control panel, the printer ignores the paper type and size settings made on the control panel. Printing is performed with the settings made on the printer driver.
5. Paper and Other Media 5. Press the [ ] or [ ] key to display [Custom Size], and then press the [OK] key. Bypass Ppr Size: Custom Size 6. Press the [ ] or [ ] key to select a unit, and then press the [OK] key. Custom Size: mm 7. Press the [ ] or [ ] key to enter the horizontal value, and then press the [OK] key. Custom Size: Horiz. 216.0 mm 8. Press the [ ] or [ ] key to enter the vertical value, and then press the [OK] key. 5 Custom Size: Vert. 356.0 mm 9. Press the [Menu] key.
Loading Paper 1. Press the [Menu] key. CMC034 2. Press the [ ] or [ ] key to display [Paper Input], and then press the [OK] key. Menu: Paper Input 3. Press the [ ] or [ ] key to display [Paper Type], and then press the [OK] key. 5 Paper Input: Paper Type 4. Press the [ ] or [ ] key to display [Bypass Tray], and then press the [OK] key. Paper Type: Bypass Tray 5. Press the [ ] or [ ] key to select the paper type, and then press the [OK] key. Bypass Tray: Plain Paper 6. Press the [Menu] key.
5. Paper and Other Media • Do not mix different types of paper in the same paper tray. • Do not move the side paper guides forcefully. Doing so can damage the tray. • Do not move the end paper guide forcefully. Doing so can damage the tray. • When inserting the tray, make sure it is not slanted. Inserting it at a slant can damage the printer. 1. Pull out tray 2 carefully with both hands. 手順はRi nmei - P1を流用してお ります。 5 CMC065 Place the tray on a flat surface. 2.
Loading Paper CMC068 4. Load the new paper stack print side down. Make sure paper is not stacked higher than the upper limit marked inside the tray. 5 CMC069 Make sure the paper is not stacked higher than the projection on the side paper guides. CMC070 rinmei-p2_com_hardware_guide_gb_00060096_eng.
5. Paper and Other Media 5. Check there are no gaps between the paper and the paper guide; both side and end paper guides. CMC071 6. Carefully push tray 2 straight into the printer. 5 CMC072 To avoid paper jams, make sure the tray is securely inserted. • The upper l i mi t di f f er s dependi ng on paper t ype; t hi n paper or t hi ck paper . Check t he engr aved l i ne i nsi de t he t r ay t o conf i r m t he upper l i mi t .
Loading Paper • The inside of this printer becomes very hot. Do not touch parts labelled " " (indicating a hot surface). • Before printing on envelopes, make sure to lower the levers on the printer rear, inside the rear cover, to avoid envelopes coming out creased. Also, pull up the levers back to their original positions after printing. Leaving the levers lowered can cause print quality problems when printing on paper other than envelopes. • Avoid using self-adhesive envelopes.
5. Paper and Other Media 2. Slide the side guides outward, then load envelopes with the print side up, and push in until it stops against the printer. Envelopes whose flaps are open must be printed with the flaps open, and envelopes whose flaps are closed must be printed with the flaps closed. Before loading envelopes, make sure they are as flat as possible. 5 CMC076 3. Adjust the side guides to the envelope width. CMC077 4. Open the rear cover.
Loading Paper 5. Lower the green levers on both sides. LCDパネルの起きた イラストに差し替 えます CMC079 Make sure to raise the levers back to their original positions after printing. 6. Close the rear cover. 5 CMC080 • After loading envelopes in the tray, specify the paper type and size using the control panel. Also, specify the printer driver's paper setting accordingly before printing. • Be sure to load envelopes so that their flaps are on the left. If you do not, the envelopes will become creased.
5. Paper and Other Media 5 92 rinmei-p2_com_hardware_guide_gb_00060096_eng.
6. Replacing Consumables This chapter explains how to replace consumables. Replacing the Print Cartridge • Do not incinerate toner (new or used) or toner containers. Doing so risks burns. Toner will ignite on contact with naked flame. • Do not store toner (new or used) or toner containers anywhere near naked flames. Doing so risks fire and burns. Toner will ignite on contact with naked flame.
6. Replacing Consumables • If toner or used toner is inhaled, gargle with plenty of water and move into a fresh air environment. Consult a doctor if necessary. • When removing jammed paper or replacing toner, avoid getting toner (new or used) on your clothing. If toner comes into contact with your clothing, wash the stained area with cold water. Hot water will set the toner into the fabric and make removing the stain impossible.
Replacing the Print Cartridge When to replace the print cartridge If the Alert indicator on the control panel lights up and the following message appears on the display, replace the print cartridge: "Replace Toner:" • Do not allow paper clips, staples, or other small metallic objects to fall inside the machine. • Do not expose the print cartridge without its cover to direct sunlight for a long time. • Do not touch the print cartridge's photo conductor unit.
6. Replacing Consumables 2. Push the side button to open the front cover, and then carefully lower it. 2 1 CMC096 3. Carefully pull out the print cartridge horizontally, holding its center. 6 CMC081 • Do not shake the removed print cartridge. Doing so can cause remaining toner to leak. • Place the old print cartridge on paper or similar material to avoid dirtying your workspace. 4. Take the new print cartridge out of the box, and then take it out of the plastic bag.
Replacing the Print Cartridge 5. Place the print cartridge on a flat surface, and then remove the protection sheet. CMC019 6. Hold the print cartridge and shake it from side to side five or six times. 6 CMC020 Even distribution of toner within the bottle improves print quality. 7. Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in. Then push down on the cartridge until it clicks into place. CMC097 8.
6. Replacing Consumables CMC098 9. Put the protective sheet you removed in step 5 on the old print cartridge. Then, put the old print cartridge into the bag, and then put it into the box. 6 CMC083 • Make sure to cover the old print cartridge with the protective cover for recycling and environmental purposes. • Comply with the print cartridge Recycling Program, whereby used print cartridges are collected for processing. For details, ask your sales or service representative.
7. Cleaning the Printer This chapter explains how to clean the printer. Cautions to Take When Cleaning • Do not remove any covers or screws other than those explicitly mentioned in this manual. Inside this machine are high voltage components that are an electric shock hazard and laser components that could cause blindness. Contact your sales or service representative if any of the machine's internal components require maintenance, adjustment, or repair.
7. Cleaning the Printer Cleaning the Friction Pad and the Paper Feed Roller If the friction pad or paper feed roller is dirty, a multi-feed or misfeed might occur. In this case, clean the friction pad and paper feed roller as follows: • Unplug the power cord from the wall outlet before you move the machine. While moving the machine, take care that the power cord is not damaged under the machine. Failing to take these precautions could result in fire or electric shock.
Cleaning the Friction Pad and the Paper Feed Roller 4. Wipe the friction pad with a damp cloth. CMC084 5. Wipe the rubber part of the roller with a soft damp cloth. After that, wipe it with a dry cloth to remove moisture. 7 CMC085 6. Reload the removed paper into the tray, and then push the tray carefully into the printer until it clicks into place. 排紙ストッパーの出てるもの に差し替え予定 CMC100 7. Insert the plug of the power cord into the wall socket securely. Connect all the interface cables that were removed.. 8.
7. Cleaning the Printer • If jams or multi-sheet feeds occur after cleaning the friction pad, contact your sales or service representative. • If the optional tray 2 is installed, clean its friction pad and paper feed roller in the same way as you did for tray 1. 7 102 rinmei-p2_com_hardware_guide_gb_00060114_eng.
8. Troubleshooting This chapter provides solutions to common problems and it also explains how to correct unwanted print results. メッセージはアルファベット順に並べ替えまし た。 Error & Status Messages on the Control Panel This section explains what the messages that appear on the control panel mean and what to do when a particular message appears. Status messages Message Explanation Recommended Action Calibrating... The printer is calibrating. Wait a while. Cancellng Job... The printer is cancelling a print job.
8. Troubleshooting Message Controller FW download failed Explanation Controller FW could not be downloaded. Recommended Action Turn off the main power, turn it back on, and then download the controller FW again. If the download fails again, contact your sales or service representative. Incorrect Tnr: K Irregular toner is set. Replace the toner to appropriate one. Internal Misfeed There is a paper jam in the fusing unit. Remove the misfed paper. The indicated tray # (1, 2, bypass) is out of paper.
Error & Status Messages on the Control Panel Message Explanation Recommended Action Repl Tnr soon The printer is almost out of toner . Prepare a new print cartridge. Replace Fusing Unit It is time to replace the Fusing unit. Contact your sales or service representative. Replace Intermdt Transfer Belt It is time to replace the transfer belt. Contact your sales or service representative. Replace Transfer Roller It is time to replace the transfer roller.
8. Troubleshooting Panel Indicator The following table explains the meaning of the various indicator patterns that the printer alerts to users about its conditions. Indicator patterns Cause The Alert indicator is lit. The printer cannot be used normally. Check the error on the control panel. The Alert indicator is flashing in yellow. Toner is nearly empty. The Data In indicator is flashing. The printer is receiving print data from a computer. The Data In indicator is lit.
Printer Does Not Print Printer Does Not Print Possible Cause Is the power on? Solutions Confirm that the cable is securely plugged into the power outlet and the printer. Turn on the power. Does the Alert indicator stay red? If so, check the error message on the control panel and take the required action. Is paper loaded? Load paper into the paper tray or the bypass tray. See p.67 "Loading Paper".
8. Troubleshooting When the Printer is Directly Connected to a Computer via USB Cable Windows When the printer is directly connected via a USB cable to a computer but the Data In indicator does not flash or light up, use the following method to check the port connection: • For a USB port connection, port USB00 (n) *1 should be set. *1 (n) is the number of printers connected. Windows XP Professional and Windows Server 2003/2003 R2 1. Access the [Printers and Faxes] window from [Start] on the taskbar. 2.
Printer Does Not Print 4. Check the [Print to the following port(s).] box to confirm that the correct port is selected. If the port (such as LPT1) is not correct, reinstall the driver. • For details about installation and port settings, see Software Guide. Windows 7 and Windows Server 2008 R2 1. Click [Start] button, and then click [Devices and Printers]. 2. Right-click the printer icon you want to check, and then click [Printer Properties]. 3. Click the [Port] tab. 4.
8. Troubleshooting 4. Click [+], and then click [Default]. 5. Select the name of the printer you are using, and then click [Add]. Check that the printer appears in the browser. If it does not, reinstall the driver. 8 110 rinmei-p2_com_hardware_guide_gb_00060120_eng.
Other Printing Problems Other Printing Problems Status Toner smears appear on the print side of the page. Possible Causes, Descriptions, and Solutions • The paper setting may not be correct. For example, although you are using thick paper, the setting for thick paper may not be set. Check the printer driver's paper settings. See the printer driver Help. • Confirm that the paper is not curled or bent. Envelopes can be curled easily. Flatten paper before loading. See p.53 "Paper and Other Media".
8. Troubleshooting Status Paper jams occur frequently. Possible Causes, Descriptions, and Solutions • Number of paper set in the tray exceeds the limit. Confirm that the top of the stack is not higher than the limit mark inside the tray. See p.67 "Loading Paper". • There may be a gap between the front end paper guide and the paper, or between the paper guide both side and the paper in the paper tray. Make sure there are no gaps. See p.67 "Loading Paper". • Paper is either too thick or too thin. See p.
Other Printing Problems Status Prints do not stack properly. Possible Causes, Descriptions, and Solutions • Paper is damp. Use paper that has been stored properly. See p.53 "Paper and Other Media". • Pull out the extender. • Perform the following operation. 1. Press the [Menu] key on the control panel, select [Maintenance], and then press the [OK] key. 修正しました。 2. Press the [ ] or [ ] key and select [Low Humidity Mo], and then press the [OK] key. 3. Press the [ ] or [ ] key, and then select [On].
8. Troubleshooting Status Multiple pages are fed at once. Possible Causes, Descriptions, and Solutions • There may be a gap between the front end paper guide and paper, or between the paper guide both side and paper in the paper tray. Make sure there are no gaps. See p.67 "Loading Paper". • Paper is either too thick or too thin. See p.53 "Paper and Other Media". • Paper has already been printed on. See p.53 "Paper and Other Media". • Number of paper set in the tray exceeds the limit.
Other Printing Problems Status Images are not printed in the right position Possible Causes, Descriptions, and Solutions Adjust the front end paper guide and both side paper guides to match the paper size. See p.67 "Loading Paper". CER090 Images are printed diagonally to the pages Adjust the front end paper guide and both side paper guides to match the paper size. See p.67 "Loading Paper". CER091 Horizontal lines appear on the printed paper.
8. Troubleshooting Status It takes too much time to resume printing. Possible Causes, Descriptions, and Solutions • The data is so large or complex that it takes time to process it. If the Data In indicator is blinking, the data is being processed. Just wait until it resumes. • The printer was in the Energy Saver mode. To resume from the Energy Saver mode, the printer has to warm up, and this takes time until printing starts. To disable Energy Saver mode: 1.
Other Printing Problems Status The whole printout is blurred. Possible Causes, Descriptions, and Solutions • Paper is damp. Use paper that has been stored properly. See p.53 "Paper and Other Media". • Perform the following operation. 1. Press the [Menu] key on the control panel, select [Maintenance], and then press the [OK] key. 2. Press the [ ] or [ ] key and select [Low Humidity Mo], and then press the [OK] key. 修正しました。 3. Press the [ ] or [ ] key, and then select [On].
8. Troubleshooting Status Possible Causes, Descriptions, and Solutions The toner is powdery and comes away from the paper, or the printed image has a matt appearance. Check if the fusing unit levers are lowered. Raise the fusing unit levers. Printed envelopes come out creased. Check if the fusing unit levers are properly set. If the problem cannot be solved, contact your sales or service representative. 8 118 rinmei-p2_com_hardware_guide_gb_00060124_eng.
Additional Troubleshooting Additional Troubleshooting Problems Strange noise is heard. No e-mail is received when an Alert occurs, and after resolving an Alert. Solutions If a supply was recently replaced or an option attached in the area the strange noise is coming from, check the supply or option is properly attached. If the strange noise persists, contact your sales or service representative. • Confirm the setting using Web Image Monitor. Confirm that [Auto E-mail Notification] setting is specified.
8. Troubleshooting 8 120 rinmei-p2_com_hardware_guide_gb_00060125_eng.
9. Removing Misfed Paper This chapter explains how to remove misfed paper. When Paper is Jammed If a paper jam occurs, the Alert indicator on the control panel flashes and one of the following messages appears on the control panel: "Internal Misfeed" "Misfeed: PprTray" "Misfeed: Tray 1" "Misfeed: Tray 2" "Misfeed: Bypass Tray" "Misfd: Dupl Unit" 追加しました。 "Misfd: Stnd Tray" 削除 Open the front cover, and check the following locations for the paper jam. • The inside of this printer becomes very hot.
9. Removing Misfed Paper Use the following procedure to remove paper that has become jammed inside the printer or in the paper feed area. 1. Pull tray 1 halfway out, and check for jammed paper. If there is jammed paper, remove it carefully. 手順はRi nmei - P1を流用してお ります。 CMC091 2. Carefully slide tray 1 back in until it stops. 3. If paper is loaded in the bypass tray, remove the paper. 4. Close the bypass tray. 5. Push the side button to open the front cover, and then carefully lower it. 2 1 9 CMC096 6.
When Paper is Jammed • Do not shake the removed print cartridge. Doing so can cause remaining toner to leak. • Place the print cartridge on paper or similar material to avoid dirtying your workspace. 7. Lifting the guide plate, remove the jammed paper carefully. 1 2 CMC088 8. Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in. Then push down on the cartridge until it clicks into place. CMC097 9 9.
9. Removing Misfed Paper • When closing the front cover, push the upper side of the cover firmly. After closing the cover, check that the error is cleared. When "Misfeed: Bypass Tray" Appears "Misfeed: Bypass Tray" appears when a paper jam has occurred in the bypass tray. Use the following procedure to remove paper that has become jammed after being fed in from the bypass tray. 1. If paper is jammed in the bypass tray input area, remove the jammed paper carefully.
When Paper is Jammed 4. Carefully pull out the print cartridge horizontally, holding its center. CMC081 • Do not shake the removed print cartridge. Doing so can cause remaining toner to leak. • Place the print cartridge on paper or similar material to avoid dirtying your workspace. 5. Lifting the guide plate, remove the jammed paper carefully. 1 2 CMC088 6. Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in.
9. Removing Misfed Paper 7. Using both hands, carefully push up the front cover until it closes. CMC098 • When closing the front cover, push the upper side of the cover firmly. After closing the cover, check that the error is cleared. When "Misfd: Dupl Unit" Appears "Misfd: Dupl Unit" appears when a paper jam has occurred in the duplex unit. Use the following procedure to remove paper that has become jammed in the exit area or inside the duplex unit. 1. Open the rear cover.
When Paper is Jammed 2. Remove the jammed paper carefully. CMC090 3. Close the rear cover. CMC080 4. Pull tray 1 halfway out, and check for jammed paper. If there is jammed paper, remove it carefully. 9 CMC091 rinmei-p2_com_hardware_guide_gb_00060128_eng.
9. Removing Misfed Paper 5. Pull tray 1 out completely with both hands. CMC092 Place the tray on a flat surface. 6. Push the blue lever. Pushing the blue lever lowers the duplex transport unit. CMC093 9 7. If there is jammed paper, carefully remove it. CMC094 128 rinmei-p2_com_hardware_guide_gb_00060128_eng.
When Paper is Jammed 8. With the duplex transport unit still lowered, carefully slide tray 1 back in until it stops. CMC053 9. If paper is loaded in the bypass tray, remove the paper and close the bypass tray. 10. Push the side button to open the front cover, and then carefully lower it. 2 1 CMC096 11. Carefully pull out the print cartridge horizontally, holding its center. 9 CMC081 • Do not shake the removed print cartridge. Doing so can cause remaining toner to leak.
9. Removing Misfed Paper 12. Lifting the guide plate, remove the jammed paper carefully. 1 2 CMC088 13. Slide the print cartridge in horizontally. When the cartridge can go no further, raise it slightly and push it fully in. Then push down on the cartridge until it clicks into place. CMC097 14. Using both hands, carefully push up the front cover until it closes. 9 CMC098 • When closing the covers, push the covers firmly. After closing the covers, check that the error is cleared.
10. Appendix This section explains maintenance and operation procedures for this printer. It also describes the specifications of the printer and its options. If the Printer is Not Going to Be Used for a Long Time If the printer is going to be inactive for a long time, follow the procedure shown here. • It is dangerous to handle the power cord plug with wet hands. Doing so could result in electric shock. • The inside of this machine becomes very hot.
10. Appendix 3. Pull the opening lever on the front cover, and then carefully lower the front cover. 2 1 CMC096 4. Lower the fusing unit levers with thumb fingers. LCDの起きているイラ ストに差し替えます。 CMC079 5. Close the front cover with both hands carefully. 10 CMC098 • This step is not necessary if the printer's power switch is on but the printer has been inactive for a long time.
If the Printer is Not Going to Be Used for a Long Time 1. Plug in the power cable. 2. Pull the opening lever on the front cover, and then carefully lower the front cover. 2 1 CMC096 3. Pull up the fusing unit levers with thumb fingers. LCDの起きているイラ ストに差し替えます。 CMC095 4. Close the front cover with both hands carefully. 10 CMC098 5. Turn the power switch to On. rinmei-p2_com_hardware_guide_gb_00060135_eng.
10. Appendix Moving and Transporting the Printer • If you have to move the machine when the optional paper tray unit is attached, do not push on the main unit's top section. Doing so can cause the optional paper tray unit to detach, possibly resulting in injury. 23. 8 kg ( 52. 5 l b. ) から修正 • The printer weighs approximately 12.0 kg (26.4 lb.). When moving the printer, use the inset grips on both sides, and lift slowly. The printer will break or cause injury if dropped.
Moving and Transporting the Printer Moving over a Short Distance タイトル変更(MF2に合わせました) • Do not remove the print cartridge when moving the printer. 1. Be sure to check the following points: • The power switch is turned off. • The power cable is unplugged from the wall outlet. • The interface cable is unplugged from the printer. 2. If Tray 2 is installed, remove it. 3. Lift the printer by using the inset grips on both sides of the printer, and then move it horizontally to the place where you want to use it.
10. Appendix • The interface cable is unplugged from the printer. • All paper trays are empty. 2. If Tray 2 is installed, remove it. • Toner might spill inside the printer if the printer is not kept level during transit. • For more information about moving the printer, contact your sales or service • representative. 削除します。 10 136 rinmei-p2_com_hardware_guide_gb_00060138_eng.
Disposal Disposal Ri nmei - P1を流用しました。 Ask your sales or service representative for information about correct disposal of this machine. 10 rinmei-p2_com_hardware_guide_gb_00060141_eng.
10. Appendix Consumables Caut i on扱いに変更 • Our products are engineered to meet high standards of quality and functionality, and we recommend that you use only the expendable supplies available at an authorized dealer. Print Cartridge Print cartridge Black "2, 500"に修正致 します。 Average printable number of pages per cartridge *1 2,000 pages, 5,000 pages *1 The printable number of pages is based on pages that are compliant with ISO/IEC 19752 and the image density set as the factory default.
P.139〜142までは、必ずご確認頂きたいセクションです。 問題ないかご確認のうえ、ご指摘ください。 Specifications Specifications "Ri nmei - P2MF2 企画仕様書- 6. xl s"および "PRO2 Syst em Funct i onal Speci f i cat i on V0. 12̲20110704. pdf " を確認のうえ修正しております。 • The supplied power cord is for use with this equipment only. Do not use with other appliances. Doing so may result in fire, electric shock, or injury.
10. Appendix Media Type See p.53 "Paper and Other Media" Paper Output Capacity Standard 125 sheets (80 g/m2, 20 lb.) Paper Input Capacity Standard Paper Tray 250 sheets *1 Bypass Tray 50 sheet *1 Optional Paper Feed Units 250 sheets *1 *1 Paper weight: 80 g/m2 (20 lb.
Specifications Weight Approximately 12.0 kg (26.4 lb.) (print cartridges included) Noise Emission *1 【ご確認】 "Noise E mission"は流用元の Perseus-P2のままとなっておりま す。実測値をご教示ください。 Sound Power Level (Main unit only) Type 2 Stand-by Printing Type 1 Less than 40 dB (A) Less than 40 dB (A) Monochrome: Less than 63 dB (A) Monochrome: Less than 62.8 dB (A) Color: Less than 64 dB (A) Color: Less than 62.
10. Appendix Printer Language PCL 6, PostScript 3 Fonts 80 fonts Options Paper Feed Unit TK1080 Paper capacity 250 sheets Paper size A4, B5 JIS, A5, Legal (81/2" × 14"), Letter (81/2" × 11), Half Letter (51/2" × 81/2") Dimensions (W × D × H) 370 × 392 × 89 mm (14.6 × 15.5 × 3.5 inches) Paper weight 60 - 105 g/m2, (16.0 – 28.0 lb.) Weight Less than 2.4 kg (5.3 lb.) 10 142 rinmei-p2_com_hardware_guide_gb_00060144_eng.
Trademarks Trademarks Adobe, Acrobat, PostScript, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. Apple, Macintosh, Mac OS, TrueType, and Safari are trademarks of Apple Inc., registered in the U.S. and other countries. Firefox® is a registered trademark of the Mozilla Foundation.
10.
INDEX A H Additional troubleshooting.................................119 Alert indicator........................................................18 Attaching Paper Feed Unit TK1010....................36 How to read this manual.........................................5 HTML manuals.......................................................12 B Bond paper............................................................57 C Cardstock...............................................................57 CAUTION labels....
O OK key...................................................................18 Operating instructions...........................................12 Options................................................................142 Other printing problems.....................................111 P Panel indicator.....................................................106 Paper capacity.......................................................53 Paper feed roller.................................................
MEMO 147 Draft 2011/08/30
MEMO 148 EN GB EN US xxx Draft 2011/08/30
Draft 2011/08/30
EN GB EN US xxx © 2011 Draft 2011/08/30