Complete Home Alerting System HA360M – USER GUIDE Copyright © 2014 Sonic Alert. All right reserved.
Table of Contents Important Safety Instructions..............................................4 HomeAware Special Features............................................6 HomeAware Identification Features ...................................7 Operations ..........................................................................8 Setting the Time of Day......................................................8 Test Mode (Testing Audio/VIB/Strobe Flash /Lamp)..........8 LED Light Indicators ...........................
IMPORTANT SAFETY INSTRUCTIONS When using your HomeAware™ HA360M, basic safety precautions should always be followed to reduce the risk of fire, electric shock and persons including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Do not use this product near a bathtub, wash basin, kitchen sink or laundry tub, in a wet basement, near a swimming pool or anywhere else there is water.160 4.
IMPORTANT SAFETY INSTRUCTIONS 13. To reduce the risk of electrical shock, do not take this product apart. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. 14. Unplug this product from the wall outlets and refer servicing to the manufacturer under the following conditions: A. When the power supply cord or plug is frayed or damaged. B. If liquid has been spilled into the product. C.
HomeAware™ Special Features • D-RF Secure™ Digital Radio Frequency Technology • Scrolling 2” extra large display • Digital display scrolls the alert message across master unit and all deluxe remote receivers. Message will read as phone, door, baby, smoke etc. • Digital display will scroll caller’s name and number across display.
HomeAware™ Identification Features 7
Operations Setting the Time of Day: 1. Press the Time set button. Blinking dots indicate time set mode has been activated. 2. Press blue arrow Hour buttons up or down and the Minute blue arrow buttons up or down to set desired time and press the Enter button. - Dots will stop blinking to indicate time has been set. Test Mode (Testing Audio/VIB/Strobe Flash /Lamp): 1. Press Enter and Back buttons together, the word TEST will be displayed. The audio, flash, vibrator and lamp will be activated.
Setting Alarm 1 1. Press and hold AL.1 Set. Blinking dots indicate Alarm set mode has been activated. 2. Press the blue arrow Hour buttons up or down and the blue arrow Minute buttons to set desired alarm time and press the Enter button. Red LED light will appears on the left side indicating alarm 1 time is set. Setting Alarm 2 1. Press and hold AL.2 Set. Blinking dots indicate Alarm set mode has been activated. 2.
Setting Audio, Flash and Vibrator Alarm 1. Press Set Up button and CLOCK will be displayed. Then press the blue Tone button until ALARM1 is displayed. Press the Enter button and AUDIO will be displayed. Press the Enter button and ON::OFF will display, and then press the blue Tone to turn the audio Off or ON and then press the Enter button. 2. Press Set Up button and CLOCK will be displayed. Then press the blue Tone button until ALARM1 is displayed. Press the Enter button and FLASH will be displayed.
Speaker Volume / Tone Setting: 1. Press the blue Volume up/down buttons to select volume level. There are 7 different volume levels and an OFF. 2. Press the blue Tone up/down buttons to select desired tone. There are 11 different tones. Testing Light Sensitivity: 1. Place hand over sensor to create darkness. Different Led brightness levels can be seen in response. Power Failure and Battery Switching: Low Bat Screen 1. LOW BAT will be seen on display if battery is not connected.
HomeAware™ Accessories Transmitters HA360DB – Doorbell HA360SS – Sound Signaler HA360BC – Baby Cry HA360SA – Smoke Alarm HA360C0 – C02 HA360DK – Door Knock Other HA360CA – CellAware HA360WA – Weather Alert HA360P – Pager HA360V – Vibrator HA360BU – Bridge Unit HA360LF – Lamp Flash 12
Regulatory Compliance PART 68 OF FCC RULES INFORMATION The HA360M complies with Part 68 of FCC Rules. You must, upon request, provide the FCC registration number and REN to you local phone company. Both numbers are shown on the HQA360M’s rating label. PART 15 OF FCC RULES INFORMATION The HA360M complies with part 15 of the FCC rules, and with RSS-210 of Industry Canada.
iii. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. iv. Consult the dealer or and experienced radio /TV technician for help Modification not expressly approved by the manufacturer could void the user’s authority to operate the equipment under FCC rules.
GENERAL DATA UL listed Power Adaptor: AC100-240V~, 50/60Hz Power Consumption: Adaptor Output: DC9V , 650mA The Lightening flash and arrowhead within the triangle is a warning sign alerting you of dangerous voltage inside the product. CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE THE COVER (OR BACK) FROM THE PRODUCT. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO YOUR SONIC ALERT DEALER.
GENERAL DATA – Attention should be drawn to the environmental aspects of battery disposal. – This indicating separate collection for electrical and electronic equipment. – SONIC ALERT’S 1 YEAR LIMITED WARRANTY The Sonic Boom Alarm Clock Model SBB500ss is warranted against manufacturing defects in materials and workmanship for one (1) year from the date of purchase. Within this period Sonic Alert will repair or replace at our option the SBB500ss without charge for parts and labor.