2 3 4 0.3 0.4 5 6 0.5 0.6 8 0.7 9 10 0.9 1.0 11 12 2.0 ALL User's Manual Safe, Easy and Reliable, 0.2 7 AlphaFire X Series (9th Generation) With remote controllable service. 0.1 0.
Contents Warning!!! ------------------------------------------------------------------------ 1 A. Firing Module ---------------------------------------------------------------- 1 A1. Parts ----------------------------------------------------------------------- 1 A2. Specification ------------------------------------------------------------- 2 A3. How to Insert / Remove Battery --------------------------------------- 2 A4.
Warning!!! A. The purpose of this device is to cause the ignition of fireworks. Fireworks are explosives and may cause personal injuries or death to yourself or others, including spectators. You are responsible for the safe and legal use of this device according to the laws and regulations of your country and/or state / province / district. RFRemotech is not responsible for illegal or unsafe use of this device.
A2. Specification Model No.: RF1XG9 Power: 1x 9V battery, 6LR61 or 6F22 or others Firing Current: >750mA, Max.9A Test Current: <1mA Low Power Indication: 1 ohm, < 700mA Sizes: L62xH46xW38mm, antenna is retractile and can be folded Power / Low Power Indication, Firing Indication, RF Signal Indication, Overload Protection, Short Warning Indication A3. How to Insert / Remove Battery Insert Battery Remove Battery A4.
A6. LED Indicator #4: Two Color LED -Red and Green. Red -A heavy current is flowing out. It appears when 3-Position Switch #2 is at ARM and the module is firing or the moduleʼs circuit is short. Dim Red -It appears when 3-Position Switch #2 is at SYNC-TEST position and no igniter is connected or the igniter is broken. Blinking Dim Red -It appears when the power is checked low to fire an igniter. Green -When 3-Position Switch #2 is at SYNC-TEST and the igniter is tested OK.
B. Transmitters / Remotes 1 2 0.1 0.2 3 4 0.3 0.4 5 6 0.5 0.6 7 8 0.7 0.8 9 10 0.9 1.0 11 12 2.0 ALL Manual Firing Manual Firing Transmitter A (1 button) Transmitter A (12 buttons) Sequential Firing Transmitter B The transmitters / remotes need to be with the following features: OOK Modulation; 433.92MHz; Learning Code. A firing module can work with 2 types of transmitter / remote: B1.
C. Synchronization (SYNC) C1. Before Synchronization Users should be aware of the following information or do some operations like below. It's better users do the step “Delete Synchronization” below in the firing module before synchronization. Only when a transmitter / remote has already been synchronized to a firing module, the both can work together. If Transmitter B is synchronized but Transmitter A is not yet, the Transmitter B will not function.
C4. Check Synchronization Shift the rod of 3-Position Switch #2 from OFF to SYNC-TEST, 1-If Button 5 of Transmitter A is already synchronized to the firing module, press Button 5 of the transmitter, the LED Indicator #4 will blink once. It indicates Button 5 is synchronized. The same with other buttons. 2-After the former step is done, press Button 0.7 of the synchronized Transmitter B, the LED Indicator #4 will blink 5 times in interval time 0.7 seconds.
This diagram means Transmitter B and the buttons of Transmitter A are already synchronized to the corresponding modules respectively. 1 2 3 4 5 6 7 8 1 2 0.1 0.2 3 4 0.3 0.4 5 6 0.5 0.6 7 8 0.7 0.8 9 10 0.9 1.0 11 12 2.0 ALL 9 Manual Firing Transmitter A Sequential Firing Transmitter B Mode 1: Manual Firing 10 11 12 Use Transmitter A, press the corresponding buttonS to fire the matching modules. Mode 2: Sequential Firing Use Transmitter B, press Button 0.
Thanks for using RFRemotech products! Manufacturer: RFRemotech E-mail: service@RFRemotech.com Http://www.RFRemotech.