Manual

ManualsBrandsRF Solutions ManualsElectronicsTransmitter keyfob for Hornet systems

HORNET Remote Control Systems

HORNET Remote Control SystemsHORNET Remote Control Systems

HORNET Remote Control Systems

DS HORNET-10

Description

DescriptionDescription

Description

Supplied complete ready to go the HORNET is a rugged IP68 weatherproof remote

control system. Built in mounting points and easy wiring using High Quality screw

Terminals.

With a range of up to100m the HORNET is ideal for a wide variety of switching appli-

cations.

Additional transmitters may be added using the ‘learn’ process, any button on the

transmitter can be used to control one or many outputs of the receiver.

• Up to 100metres Range

• 1 – 3 Button versions

• 12-30Vdc 0r 230Vac versions

• Reliable FM Technology

• Up to four 1000W Relay switches

• Waterproof Receiver (IP68)

• Momentary or Latching Relays

• Any Switch Map to Any Relay

Output

• General Purpose Remote

General Purpose Remote General Purpose Remote

General Purpose Remote

Switching

SwitchingSwitching

Switching

• Electric Gates

Electric GatesElectric Gates

Electric Gates

• Roller Shutter Doors

Roller Shutter DoorsRoller Shutter Doors

Roller Shutter Doors

• Garden Lighting

Garden LightingGarden Lighting

Garden Lighting

Summary of content (9 pages)

PAGE 1
HORNET Remote Control Systems • • Up to 100metres Range • 1 – 3 Button versions • 12-30Vdc 0r 230Vac versions • Reliable FM Technology • Up to four 1000W Relay switches • Waterproof Receiver (IP68) • Momentary or Latching Relays • Any Switch Map to Any Relay Output General Purpose Remote Switching • Electric Gates • Roller Shutter Doors • Garden Lighting Description Supplied complete ready to go the HORNET is a rugged IP68 weatherproof remote control system.
PAGE 2
HORNETHORNET-S1 / HORNETHORNET-S2 / HORNETHORNET-S3 (12(12-32Vdc Receivers) The HORNET system provides up to 4 isolated switches each capable of switching up to 6A @230V 1. 2. 3. 4. Open the enclosure by removing the two fixing screws from the base of the enclosure and remove the antenna, the board should then slide out. Wire the power as shown on Fig 1.1 Wire your chosen switch as required Once the receiver is set-up; transmitter button 1 will switch relay 1 (button two to relay two and so on).
PAGE 3
Advanced Operation To pair a new transmitter switch follow this procedure Any transmitter button can be configured to operate any of the receiver relays. Pair any Transmitter switch with a receiver relay by following this procedure: 1. 2. 3. 4. 5. 6. 7.
PAGE 4
HORNETHORNET-S1M / HORNET S2M (230Vac Powered Receivers) The HORNET system provides up to 4 isolated switches each capable of switching up to 6A @230V 1. 2. 3. 4. Open the enclosure by removing the two fixing screws from the base of the enclosure and the antenna, the board should then slide out. Wire the power as shown on Fig 1.2 Wire your chosen switch as required Once the receiver is set-up transmitter button 1 will switch relay 1 (button two relay two and so on).
PAGE 5
Advanced Operation Please Note: During Learn and Erase the relays operate at high speed. They should be isolated from sensitive equipment during this process. To Pair additional Transmitter buttons to receiver Relay #1 1. Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode. 2. Switch the receiver unit OFF and then ON again in ~1sec intervals FOUR times finally leaving the unit powered. 3.
PAGE 6
System Part Numbers Operating from 1212-30Vdc Frequency Range** (MHz) (Metres) System 1 channel 433.92 100 HORNET-S2 System 2 channel 433.92 100 HORNET-S3 System 3 channel 433.92 100 Frequency Range** (Metres) 100 100 Part Number Description HORNET-S1 Systems Operating at 230Vac Part Number Description HORNET-S1M System 1 channel (MHz) 433.92 HORNET-S2M System 2 channel 433.92 **Range stated is optimum, direct line of sight.
PAGE 7
Low Battery Indication When the battery on the HORNET-TX becomes low (<2.1V) the LED will indicate this by pulsing on and off and one second intervals. The battery should be changed at this point. When the battery reaches this level the HORNET-TX may continue to operate but the range will be reduced and the LED will dim. Technical Specifications Transmitters: HORNET Enclosure Rating: Battery Type: Battery Life Est.
PAGE 8
Receiver Decoder HORNETHORNET-RX Enclosure Rating Dimensions Storage Temperature: IP68 130 x 112 x 42 mm (not including antenna) -10 to +70o Celsius. ELECTRICAL CHARACTERISTICS Supply Voltage for 12-30V versions Min Typical Max Units 10.5 12 30 Vdc Supply Voltage for Mains versions Relay Rating* (230Vac) RLY1-4 Supply Current : @12V -10 to +50o Celsius.
PAGE 9
Installation diagram NOT TO SCALE Disclaimer Whilst the information in this document is believed to be correct at the time of issue, R.F.Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness. No express or implied warranty or representation is given relating to the information contained in this document. R.F.Solutions Ltd reserves the right to make changes and improvements to the product(s) described herein without notice.