EAGLE RE-1 CONTROLLER For Use On MotoSAT HD Mounts Supported Systems HD SL5 DirecTV HD DP3 Dish Network HD SC2 SHAW HD DP3 BELL TV EXECUTIVE DirecTV 101 Dish Network 119 MSC-60 SHAW MD-500 Dish Network MD-1000 Dish Network Made in USA 24 April 2014 1
Index Disclaimer ........................................... 3 Parts Bill of Materials ................................. 4 Requirements for Installation ..................... 5 What you wish you had .............................. 6 Installation ................................................. 7 Wiring Diagrams ....................................... 8 Menus and Operation ................................. 10 Updating and Maintaining Software .......... 11 How to Measure Focal Points .......
Disclaimer • • • • • • • • • • • • • • The RF Mogul EAGLE RE-1 is designed to operate all MotoSAT mounts with the exception of the round 24" single LNB reflector. It will operate the DirecTV, Dish Network, SHAW and Bell TV HD systems. The MotoSAT mount must be mechanically sound with functional motors and count sensors. The antenna must not be bent "tweaked" or damaged in anyway.
Bill of Materials 1. 2. 3. 4. 5. 1 ea. 1 ea. 1 ea. 1 ea. 1 ea.
STOP !!! YOU MUST CHECK AND CORRECT THE FOCAL POINT OF YOUR DISH BEFORE DOING BEGINNING YOUR INSTALL. FAILURE TO DO SO WILL CREATE PROBLEMS IN ACQUISITION!!! (See page 13 for details) Requirements for Installation • Color Blind? Ask a friend or neighbor for assistance. Meet a new friend. • Patience and attention to details will make this go smoothly. Do not rush through this document. Analyze each step and consider the implications of skipping or ignoring any of the steps or recommendations.
What you wish you had Pre-installation recommendations for the RF Mogul Eagle Controller to a MotoSAT mount... 1. 2. 3. 4. 5. 6. 7. The ability to receive Email and download files from an Email. Know how to put files on a USB Flash Drive from your computer. Read and follow wiring instructions. Cannot be color blind. A basic Volt/Ohm Meter. One small screw driver for use on the 12 position control cable connector. Flashlight Recommended Tools for the RF Mogul Eagle to MotoSAT Upgrade 1. 2. 3. 4. 5. 6.
INSTALLATION If your system is equipped with a GPS, it is required that you bypass your existing GPS and splitter on the roof. A simple barrel connector will allow you to bypass the MotoSAT GPS and splitter. The coax cable inside the mount must go directly to the LNB from the controller. The GPS/Splitter is located in two possible locations.... 1. On the roof near the GPS or 2. Under the cover located in front of the mount as shown.
Wiring Diagram For the Control Cable 12 Pin Connector Wiring Color Code Pin Color MotoSAT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Black Brown Red Orange Not Used Not Used Yellow Blue Purple Green 12. Color RF Mogul How Used Black Red /Blue Light Adapter White Motor, Azimuth Motor, Azimuth/Skew Motor, Elevation/Skew Motor, Elevation Not Used Not Used Sensor Count, Azimuth Sensor Count, Elevation Sensor Count, Skew Ground Power, Blue light Connection GPS TXD 1.
Note: If you do not wire this connector properly damage to your mount could be a result. Double check all connections before applying power. Connecting the Blue Light Adaptor Connection of Blue Light Adaptor using a snap type connector. For splicing, cut wire blunt before inserting into the Scotch Lock connector.
Menus and Operation Your controller is menu driven. By selecting a particular menu you can perform many functions besides just "SEARCHING for satellite". TO SEARCH • Press Power button o Displayed will be the.... System configuration (software configuration) HD Mounts • • • • • • ms HD 1 = Shaw Triple Satellite xKu LNB ms HD 2 = DirecTV SWM 3 LNB Option ms HD 3 = Dish Network Triple Satellite 1000.2 LNB ms HD 4 = Bell TV Triple Satellite 1000.
• • • • • • • • 5: move elevation - pressing and holding the appropriate button will manually move your mount in elevation (Up arrow UP, Down arrow DOWN 6: move skew - pressing and holding the appropriate button will manually move your dish in skew (Up arrow right side DOWN, Down arrow left side DOWN 7: test dish - will move the dish in all axis for one complete cycle 8: temperature - will display current operating temperature of its operating environment.
Most "low signal" can be attributed to improper focal point. The following will assist you in determining if you have problems with your reflector or LNB arm.
INTRODUCTION AND HOW TO MEASURE It is important to remember that the focal point of any HD Series mount will always be measured from a specific point. Follow these simple rules and you will be able to determine the focal point of your dish. All of these measurements will be plus/minus ¼ inch. Step #1 Step #2 Place the leading edge of your measuring tape over the lip of your dish in this manner. Place the trailing edge of your measuring tape to the point specified by your LNB type.
DIRECTV SL5 (Circular Polarized 99 Ka, 101 Ku, 103Ka, 110 Ku, 119 Ku) STRAIGHT LNB 26 ” Measure to front edge of the LNB Cover. CURVED LNB 26 “ Measure to front edge of the LNB Cover.
DISH NETWORK DP3 (Circular Polarized 110 Ku, 119 Ku, and 129 Ku) BELL TV (Circular Polarized 82 Ku and 91 Ku) 26 3/8 “ Measure to the front edge of the LNB cover.
SHAW DIRECT (Linear Polarized 107.3 Ku and 111.1 Ku) For HD-SC2 Mounts 24 ⅜” For MSC60 Mounts 21 ½” Measure to the point just behind the white LNB cover.
ASSISTANCE For questions or assistance concerning this product please contact your installing dealer. For additional assistance you may contact support@rfmogul.com. This product was manufactured in the United States of America. RF Mogul 3604 South Via Terra Salt Lake City, UT 84115 801-895-3392 support@rfmogul.com sales@rfmogul.