Wi-Fi Smart Fingerprint Lock Installation Manual
DOWNLOAD REVOLO APP Download the Revolo APP from the APP store or Google Play. Scan the QR code to download the Revolo APP If you have any questions, please contact support@irevolo.com.
CONTENT Process Guide ................................................................................................................................................01 What’s Included .............................................................................................................................................02 Product Overview ..........................................................................................................................................
PROCESS GUIDE 1 2 Download the Revolo app to setup. Follow the instructions and replace your existing lock. 4 3 Scan the QR code on you device. Calibrate your lock and you are done.
WHAT’S INCLUDED B C D E F G H K L 2¾ A 2⅜ I M J N (optional) O 02
PRODUCT OVERVIEW Battery Cover Fingerprint Touchscreen Cylinder Cover Reset Button Cylinder Type-C Port Thumb Turn Multifunction Button DEFINATION Lock-Out: If you fail to unlock the door for 5 consecutive times using the PIN Key, your Lock will be shut-down for 3 Mins. One Touch Locking: Press and hold Any key on keypad for 2 Seconds to lock the door. Multifunction Button: Push and HOLD the Multifunction Button on inside panel for 3 Seconds to active Privacy Mode.
PREPARE DOOR FOR INSTALLATION 1. Make sure that the following criteria are met so that the Smart Lock can be installed properly: ① Check the door status. Make sure the doorframe is aligned with the door. ② There are no obstructions stuck in the doorframe. ③ Leave enough space for the deadbolt to extend into the doorframe when the door is locked. 2.
INSTALLATION GUIDE STEP 1 INSTALLING THE LATCH AND STRIKE To install the deadbolt: 1.1 Measure your door’s backset dimension: whether it is 2¾”(70 mm) or 2⅜” (60 mm) . 1.2 If your door’s backset dimension is 2⅜” (60 mm), use the provided deadbolt to install. If your door’s backset is 2¾” (70 mm). Rotate and pull the latch as shown the extended latch. The bolt must be in retracted(Unlocked) position when you are changing backset. 90° 2¾ 2⅜ 2¾ 2⅜” 60 mm 2⅜ 2¾” 70 mm 1.
b. If not chiseled not chiseled Install latch in door with wood block and hammer. Use a flathead screwdrive to remove rectangular face from latch and install driver-in collar. 1.5 Install strike on the door frame. IMPORTANT: Make sure hole in door frame is drilled a minimum of 1” (25mm) deep.
STEP 2 INSTALLING EXTERIOR ASSEMBLY IMPORTANT:Before installation, make sure the latch is fully retracted (in the unlocked position). To install the exterior assembly: 2.1 Measure your cross bore dimension and determine the installation steps accordingly. J (optional) • If the diameter of your cross bore is 2⅛”(54mm), install directly. • If you have a 1½”(38mm) crossbore, remove the spacer.
STEP 3 INSTALLING THE MOUNTING PLATE 3.1 Send the cable through the bottom slot in the mounting plate. Cable 3.2 Secure the mounting plate with the supplied screws.
STEP 4 INSTALLING INTERIOR ASSEMBLY 4.1 Remove the battery cover. 4.2 Connect the cable to the corresponding port.
4.3 Rotate the thumb turn in vertical position, then push the cable back to the hole of mounting plate and install the interior assembly. 4.4 To avoid stucking the cable and the RF cable, secure the interior assembly with supplied screws. N Make sure the thumb turn is vertical.
4.5 Test the thumb turn manually for smooth rotation. If thumb turn doesn’t rotate, make sure the thumb turn in vertical position. 4.6 Insert the Li-battery into the battery case matching the battery connector.
4.7 Scan the QR code to pair your device with your phone. Close battery cover.
STEP 5 PAIR AND SET UP YOUR SMART LOCK VIA APP Note: The lock will not lock automatically before the setting is completed. To avoid being locked outside, pair your phone with the Smart Lock and set an access code unlocking the door. To pair your phone with Smart Lock. 5.1 Scan the QR code on the back of the Smart Lock to get the information of the Smart Lock. Follow the on-screen instructions to complete the setup.
STEP 6 INSTALLING DOOR SENSOR For optimal performance, Door Sensor should be mounted within 1” from the edge of your door, and within 1” from the top of the interior assembly. Surface Mount <1 (25mm) M X 6.1 Determine mounting location. 6.2 Stick the mounting tape to the door sensor. 6.3 Stick it on door frame. 6.4 Calibrate your Lock.
Flush Mount 1 2 3 4 1. Remove magnet from housing 2. Attach magnet to cap 3. Determine mounting location and Drill the hole on your doorframe: a. more than 1”(25mm) to 1.5”(38mm) from the top edge of your deadbolt strike plate, b. Requires a ½” (12.5mm) deep hole, 5 c. Requires a 8 ”(16mm) inch diameter hole. 4.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.