WiFi Smart Lock Quick Start Guide
1 Download the Revolo app to begin setup. 3 Follow the instructions and replace your existing lock. 2 Use your phone’s camera to scan the QR code on you device. 4 Calibrate your lock and you are done.
WHAT’S INCLUDED 2¾ 2⅜
PRODUCT OVERVIEW Battery Cover Touchscreen Battery Indicator Cylinder Cover RES Reset Button Multifunction Button Cylinder Thumb Turn Type-C Port DEFINATION Multi-function Button Push and HOLD the Multi-function button on inside panel for 3 Seconds to active Privacy Mode. This will disable all user PIN code access and APP control. Privacy Mode will be disable autometically after unlock the device with the Thumb Turn or Mechanical Key.
Type-C Port Insert a Type-C cable into the Type-C port and use a portable bettery to power the Smart Lock. If your device’s batteries are completely ran out. Starts Here! DOWNLOAD REVOLO APP Download the Revolo APP from the APP store or Google Play. Note: The Revolo WiFi Smart Lock is embedded with an encryption chip.Bluetooth&WiFi data, and all user credenticals are all encrypted, so user information is secure and cannot be accessed by others.
PREPARE DOOR FOR INSTALLATION 1. Make sure that the following criteria are met so that the Smart Lock can be installed properly: ① Check the door status. Make sure the doorframe is aligned with the door. ② There are no obstructions stuck in the doorframe. ③ Leave enough space for the deadbolt to extend into the doorframe when the door is locked. 2.
Door thickness 1⅜ (35mm)2 (50mm) Door hole 1 (25mm) STEP 1 INSTALLING THE LATCH AND STRIKE To install the deadbolt: 1. Measure your door’s backset dimension: whether it is 2¾ (70 mm) or 2⅜ (60 mm) . 2. If your door’s backset dimension is 2⅜ (60 mm), use the provided deadbolt to install. If your door’s backset is 2¾ (70 mm). Rotate and pull the latch as shown the extend latch. The bolt must be in retracted(Unlocked) position when you are changing backset. 90° 2¾ 2⅜ 2⅜ 60 mm 3.
4. Screw into the doorframe with a screwdriver (not provided). a if chisled chisled actual size b if not chisled not chisled Install latch in door with wood block and hammer.
Use a flathead screwdrive to remove rectangular face from latch and install driver-in collar. 5. Install strike on the door frame. IMPORTANT: Make sure hole in door frame is drilled a minimum of 1 (25mm) deep.
STEP 2 INSTALLING EXTERIOR ASSEMBLY IMPORTANT: Before installation, make sure the latch is fully retracted(in the unlocked position). To install the exterior assembly: 1. Measure your cross bore dimension and determine the installation steps accordingly. • If the diameter of your cross bore is 2⅛ (54mm), install directly. • If you have a 1½ (38mm) crossbore, remove the spacer.
2. Route the cable connected on the exterior assembly under the deadbot. Align the tailpiece with center hole of the deadbolt, and insert it into the center hole. Insert the tailpiece into the center hole STEP 3 INSTALLING THE MOUNTING PLATE 1. Send the cable through the bottom slot in the mounting plate.
2. Secure the mounting plate with the supplied screws. Keep parallel to door edge unlocked actual size STEP 4 INSTALLING INTERIOR ASSEMBLY 1. Remove the battery cover.
2. Connect the cable and ensure tight cable connection. 3. Rotate the thumb turn in vertical position and install the interior assembly.
4. Secure the interior assembly with supplied screws. actual size RES Make sure the thumb turn is vertical. 5. Test the thumb turn manually for smooth rotation.
6. Insert four AA batteries into the battery compartment matching the polarity (+/-)indicated. RES 7. Scan the QR code to pair your device with your phone. Close battery cover.
STEP 5 PAIR YOUR PHONE WITH SMART LOCK AND SET UP YOUR SMART LOCK THROUGH APP Note: The lock will not lock automatically before the setting is completed. To avoid being locked outside, pair your phone with the Smart Lock and set an access code unlocking the door. To pair your phone with Smart Lock. 1. Scan the QR code on the back of the Smart Lock to get Bluetooth information of the Smart Lock. Follow the on-screen instructions to complete the setup.
STEP 6 INSTALLING DOOR SENSOR For optimal performance, Door Sensor should be mounted within 1 from the edge of your door, and within 1 from the top of the interior assembly. Surface Mount <1 (25mm) <1 (25mm) 1. 2. 3. 4. 5. 6. Determine mounting location. Attach mounting tape. Place on door frame. Screw into frame (optional). Attach the cover. Calibrate your Lock.
Flush Mount 1 2 3 4 1. Remove magnet from housing 2. Attach magnet to cap 3. Determine mounting location and Drill the hole on your door frame: a. more than 1 (25mm) to 1.5 (38mm) from the top edge of your deadbolt strike plate, b. Requires a ½ (12.5mm) deep hole, c. Requires a 5 8 (16mm) inch diameter hole. 4.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two cond itions: (1) this device may not cause harmful interference, and (2) this device must accept any int e rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could v oid the user's authority to operate the equipment.