Installation and Operation Manual SOLO – EXECUTIVE Wireless Microphone System (01-EXESYS and 03-EXESYSEU)
© 2006 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permission from Revolabs, Inc. Product specifications are subject to change without notice. Solo – Executive Manual 01-EXEMAN-PAP-11 Mfg. #91-8562-30N00 August 2006 (Rev 2.
Table of Contents Safety and General Information................................................ 2 FCC User Information ..................................................................... 2 European Compliance..................................................................... 3 Safety Compliance .......................................................................... 3 System Components ................................................................ 4 Solo Executive Charger Base.....................
Safety and General Information IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION. READ THIS INFORMATION BEFORE USING YOUR DEVICE. FCC User Information FCC Registration Number: 0014898290 FCC ID Number: T5V01EXESYS Solo Executive Base Station FCC ID Number: T5V01EXEMIC Solo Executive Microphone FCC Notice to Users Users are not permitted to make changes or modify the equipment in any way. Changes or modifications not expressly approved by Revolabs, Inc.
Export Law Assurances This product is controlled under the export regulations of the United States of America and Canada. The Governments of the United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce or the Canadian Department of Foreign Affairs and International Trade. The use of wireless devices and their accessories may be prohibited or restricted in certain areas.
Introduction Congratulations on the purchase of a Revolabs digital wireless communication system! We are pleased that you have chosen the Solo Executive Wireless Microphone System with 1.9 GHz DECT technology. The Solo Executive provides high band-width audio from multiple wireless microphones enabling reliable, un-tethered communications in audio and video conferences. The Solo Executive Wireless Microphone System is a unique marriage of innovative technology and ergonomic stylish design.
Solo Executive Charger Base The Charger Base is used for storage and charging the microphone when not in use. Microphones must be properly inserted into the base and seated flush for charging to occur. 4 1. System MUTE Switch — overrides individual Microphone mute function. 2. LED indicator — power / mute status indicator. 3. Charger Bays — charges up to 8 Microphones. 4. Line Cord Receptacle — power supply input (on rear). 2 1 3 Power Module The Charger Base requires 5VDC power.
Charging the Batteries How to Charge 1. Place microphone(s) into the Executive Charger Base. 2. During charging, the LED indicator turns on (RED) and remains on until charging completes. The microphones are muted while in the Charger Base. In normal use, batteries should fully charge in about 2 hours, and can be “quick-charged” to 80% capacity in 45 minutes. 3. When charging completes, the LED turns off and the microphone is ready for use.
Adjusting the Volume The volume of the microphone is set at the factory and cannot be adjusted on the wireless microphone. Access to each channel is provided on the Base Station for external amplification. Note: Moving the wireless microphone closer to the mouth will increase the volume. To change the volume on the earpiece, use the dial on the earpiece wire. Turning the dial towards the earpiece will increase the volume, and turning the dial towards the microphone will decrease the volume.
Installation The Executive Base Station is easily installed into a standard 19” AV rack system using the supplied rack ears and standard rack screws. The equipment requires 110-220V AC, 50-60 Hz, power. Plug the power cord into an appropriate outlet and turn the circuit breaker-protected power switch on the back panel to Reset. The GREEN power LED on the front panel will illuminate. Attach the four diversity antennas (two on each side) and the system mute antenna (SMA male connector) in the center.
If a microphone is lifted from the Charger Base and the LEDs continuously flash alternating RED and GREEN, and/or the Base Station LED flashes alternating RED and GREEN, the microphone needs to be paired to the system. Make sure that all other microphones are properly paired, and that the Base Station is powered on, before proceeding to pair an individual microphone. By noting which microphone channels are already in use (paired), it will be obvious which channel to use for pairing the microphone.
System Mute Function Switch In certain circumstances it is preferable to use the muting capabilities in a DSP based automated microphone mixer instead of the Charger Base system mute. This is the case when the mixer is providing acoustic echo cancellation and needs a continuous signal to maintain a near-end audio reference. The two position System Mute switch located on the back panel controls how the Base Station handles the audio output for muted channels.
Using Multiple Systems If more than one Base Station is required for an area, each unit needs to be interconnected with a sync cable using the supplied mini-phoenix connector. The three terminals correspond to positive +, negative −, and ground . Use the screws on top of the connector to first loosen the terminal to insert an appropriate three conductor cable (3 conductors, or 2 conductors and shield), and then tighten the screw to secure. Push the connector onto the pins labeled BUS.
System Functions The following table shows the functions supported by the Solo Executive System: Function Base Wireless Station Microphone Status Status Enter Pairing Mode On Action Off Press the Microphone MUTE button for about 7 seconds (LED solid RED), and then press the MUTE button on the Charger Base for about 7 seconds (LED solid RED). On A short press of the Microphone MUTE button or Charger Base MUTE button causes flashing RED LED on each unit indicating that the Microphone has audio muted.
Indicator LEDs The following tables show activities associated with the various states shown by the LEDs: Equipment Use Microphone LED Microphone in Charger Base Microphone not in Charger Base Solid RED OFF Base Station Channel LEDs OFF OFF OFF OFF Two RED flashes every 1.5 seconds GREEN flash every 1.
Equipment Use Microphone LED Charger Base LED Meaning Microphone in Charger Base OFF OFF Charger Base is unplugged GREEN Flashing Solid GREEN RED Flashing Solid RED Equipment Use Microphone Earpiece Microphone not in Charger Base Five rapid tones repeated every 30 seconds No audio or deteriorating audio quality Five rapid tones repeated every 20 seconds Microphone not in Charger Base Microphone is “live” Microphones muted using Charger mute Audio Indicators 14 Meaning Microphone out of
Warranty Revolabs, Inc. warrants this product to be free of manufacturing defects. Repair or replacement of any defective part or unit (at the discretion of the Seller) will be free of charge for the period of one year. Any attempt by the user to alter the equipment, or equipment damaged by negligence, accident, or Acts of God voids this warranty. The Seller shall not be liable for any consequential damage resulting from the malfunction of this product.
System Specifications Dimensions, (L, W, H) and Weight Executive Base Station 16.9” (43.03 cm) x 8.0” (20.32 cm) x 1.7” (4.42 cm), 6.5 lbs (2.95 kg) Charger Base 8.3” (21.1 cm) x 4.3” (10.9 cm) x 1.0” (2.56 cm), 1.0 lb (0.45 kg) Wireless Microphones 0.9” (2.4 cm) x 0.8” (1.95 cm) x 2.6” (6.68 cm), 0.05 lb (0.01 kg) Shipping Weight 12.0 lbs (5.45 kg) Radio Frequency 01-EXESYS 03-EXESYSEU Connectors Base Station Charger Base Microphone 1.92 to 1.