Installation and Operation Guide © 2007 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permission from Revolabs, Inc. Product specifications are subject to change without notice. Revolabs Solo™ Single Channel Wireless Microphone System Models 02-DSKSYS, 04-DSKSYSEU Revolabs, Inc. Revolabs Solo™ Single Channel 02-DSKMAN-PAP-11 December 2007 (Rev 3.
Table of Contents Safety and General Information.....................................................1 Introduction ....................................................................................4 System Components .....................................................................5 Revolabs Solo™ Single Channel Charger Base ...........................5 Mute Button ...............................................................................6 Power Module ...........................................
Other Medical Devices WEEE Notification: If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. The Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC) is intended to promote recycling of electrical and electronic equipment and their components at end of life.
System Components Introduction Congratulations on the purchase of your Revolabs Solo™ Single Channel wireless microphone system! This wireless system provides high band-width audio from a compact wireless microphone enabling reliable, secure, and untethered personal communication. The Single Channel Wireless Microphone System is a unique marriage of innovative technology and ergonomic stylish design, featuring 1.9 GHz DECT technology.
Mute Button Pressing the MUTE button toggles between muting (flashing RED LED status) and un-muting (flashing GREEN LED status) on the Wireless Microphone. Note: Press the MUTE button on a Microphone will similarly toggle between mute and un-mute and display on both status LEDs. Power Module The Charger Base requires 5VDC power. Plug the supplied AC adapter into a convenient 110-240VAC, 50-60Hz power outlet and the adapter into the power connector.
4. Open the Volume settings for Sound recording to view the volume levels selected for the microphone input (Capture) on the computer. The Sounds and Audio Devices Properties dialog will display, as shown. The solo-Desktop device will be selected. 5. Make sure that the level for the Microphone is close to the top (maximum) and that the Mute box is not checked. 6. In the Sound playback section, open the Volume settings for to control the volume you hear in the Microphone’s earpiece.
. At the bottom of the Microphone section, click the Mute box in the Microphone section to prevent the Microphone directly feeding back its own audio to the earpiece (i.e. “sidetone”). It may be necessary to use the OptionsProperties menu to display the Microphone volume control. IP telephony and computer telephony applications (e.g., Skype) may also offer options for controlling the audio levels and playback capabilities.
Revolabs Solo™ Wireless Microphones Microphones Using with Wearable Wireless Microphone The wireless personal microphone uses encrypted communication to synchronize with the Charger Base. It provides high quality full duplex audio between the user and the computer, audio or video conference system or external audio system. The system allows the wearer to step out of the office or conference room and still participate in the call. 1. Microphone port — direct toward mouth for best audio pickup. 2.
LED), to reduce noise while placing the microphone on the table. Turning the dial towards the earpiece, as shown in the figure, will increase the volume, and turning the dial towards the microphone will decrease the volume. Use the attached clothing clip to secure the earpiece wire. Using with TableTop Microphone The Revolabs Solo™ TableTop Wireless Boundary Microphones enable multiple phone conference participants to use a single microphone.
microphones for wireless freedom during open mic meetings, Q&A sessions, classrooms, etc. The Adapter does not provide phantom power or bias current so it cannot be used with condenser or electret microphones. 7. 1. Mute button — press to mute, un-mute and pair microphone. 8. 2. Rubber collar — durable and impact/strain protection. 9. 3. XLR Female connector — balanced audio for dynamic microphones. 10. 4. LED display — visual status for mute, un-mute, and pairing. 11. 5. Audio Out port — accepts the 2.
be re-established to its original state, and the beeping will cease. If not, the microphone will turn off. Using with a Solo Executive Multi-channel System The Revolabs Solo™ Single Channel Wearable Microphone can be paired to a Solo Executive Multichannel Wireless Microphone System for users who wish to have a single microphone to use in both the office and in the conference room.
Executive Single Channel system broadcast/receive power. alternately GREEN and RED for a few seconds and turn OFF. If this happens, repeat these steps. Pairing the Microphone to the Charger Base “Pairing” creates an encrypted association between the Wireless Microphone and the Charger Base with a unique electronic serial number. When the Microphone and Charger Base have been previously paired, the Microphone will automatically try to connect to the Charger Base whenever it is lifted from the Charger Base.
LED Status Indications Warranty The following LED patterns are shown on either the Microphone or the Charger Base. Revolabs, Inc. warrants this product to be free of manufacturing defects. Repair or replacement of any defective part or unit (at the discretion of the Seller) will be free of charge for the period of 90 days. LED Pattern Solid GREEN (Microphone only*) Solid RED GREEN flash every 1.5 seconds Two RED flashes every 1.
Solo Single Channel Specifications Dimensions, (L, W, H) and Weight Single Channel Charger Base 3.9” (10 cm) x 2.4” (6 cm) x 1.0” (2.56 cm), 0.5 lb (0.23 kg) Wearable Microphone: 0.9” (2.3 cm) x 0.8” (2.0 cm) x 2.6” (6.6 cm), 0.05 lb (0.02 kg) TableTop Microphone: 1.5” (3.8 cm) x 0.8” (2.0 cm) x 3.3” (8.4 cm), 0.05 lb (0.02 kg) XLR Adapter: 0.9” (2.3 cm) x 0.8” (2.0 cm) x 4.0” (10.2 cm), 0.05 lb (0.02 kg) Shipping Weight 1.5 lbs (0.68 kg) Radio Frequency 02-DSKSYS - 1.92 to 1.