Revolabs HD™ Single/Dual Wireless Microphone System Models: 02-HDSGL, 02-HDDUAL, 04-HDSGLEU, 04-HDDUALEU, 04-HDSGLCN, 04-HDDUALCN User and Set-up Guide
© 2010-2014 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permission from Revolabs, Inc. Product specifications are subject to change without notice. Revolabs HD™ Single & Dual Manual 01-HDSGLMAN-PAP-11 April 2014 (Rev 2.
Contents Safety and General Information .................................................................................................................... 4 Introduction.................................................................................................................................................... 8 System Components ................................................................................................................................
Safety and General Information Please read the following information to ensure safe and efficient use of your Revolabs system. FCC User Information FCC ID: T5V02HDDUALNM Revolabs HD™ Dual Base Station FCC ID: T5V0HDEXEMIC Revolabs Executive HD ™ Microphone FCC Notice to Users This device complies with Part 15 of the FCC Rules.
Industry Canada Notice to Users This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation of the device Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Export Law Assurances This product is controlled under the export regulations of the United States of America and Canada. The Governments of the United States of America and Canada may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce or the Canadian Department of Foreign Affairs and International Trade. The use of wireless devices and their accessories may be prohibited or restricted in certain areas.
WEEE Notification: The Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EU) is intended to promote recycling of electrical and electronic equipment and their components at end of life. According to the requirement of the WEEE legislation the following user information is provided to customers for all branded Revolabs products subject to the WEEE directive. “The symbol on the product or its packaging indicates that this product must not be disposed of with your other household waste.
Introduction Congratulations on your purchase of a Revolabs Digital Wireless Microphone System! This system utilizes 1.9 GHz DECT technology, and high band-width audio from multiple wireless microphones, enabling clear, reliable, un-tethered communications in recording, audio/video conferencing, speech recognition, VOIP communications, sound re-enforcement as well as many other environments requiring clear audio capture.
Acoustic echo cancellation (AEC) Feedback elimination Level control Equalization Noise cancellation The system is designed to optimize audio capture/reproduction by providing: Consistent audio input from all participants Minimum room noise Mute control Wireless encryption Automatic channel selection Full duplex audio The Charger Base charges the HD Wireless Microphones and stores them when not in use.
To Install the Base Station: 1. Plug the power cord into an appropriate outlet 2. Connect the necessary outputs and inputs Revolabs HD™ Base Station Audio Connections There are (2) 3.5mm balanced inputs and (2) 3.5mm balanced outputs on the back panel of the unit providing access to each channel’s audio signal. The three terminals correspond to: Tip = Positive + Ring = Negative – Sleeve = Shielded Ground There are one or two output channels representing a separate channel for each microphone.
Using the Rear Panel Configuration DIP Switches off on 12345678 DIP Switch Feature Off (Default) On Individual Outputs Mixed Output No LPF LPF 1 Output Mixing 2 Low Pass Filter 3 Audio Output Level Line Level Mic Level 4 Mute Mode Individual Mutes No Mutes Off Off High boost On Off Bass Boost Off On 150' Off Off 100' On Off 50’ Off On Flat 5 6 7 8 Microphone EQ Transmit Power Dynamic On On 15' On On Configuration Settings DIP Switch 1- Output Mixing: When DIP Switch 1 is OFF(d
When DIP switch 4 is OFF(default) each microphone has its own individual muting capabilities. When DIP switch 4 is ON, the microphone mute buttons are deactivated resulting in the mics always being active and un-muted when not in the Charger Base. DIP Switch 5&6 – Microphone EQ: There are four EQ options for the microphone outputs of the Base Station. One of these options can be activated for both microphones.
Configuration Settings The Revolabs HD Control Panel controls most of the HD Single/Dual Base Station configuration settings. It also provides real time status of the microphones. Only one HD Single/Dual system can be controlled and monitored from a single PC at any given time. Mics Unmute at Startup: By default the mics go into a muted state when they are removed from the charger. This is done to prevent handling noise as the microphone is placed into position.
Mute: Each microphone has individual mute capabilities. The HD Control Panel Software provides the user the ability to mute and unmute a microphone from their PC. These mute controls will always remain synchronized to the actual state of the microphone. If the microphone state is changed at the microphone, the mute controls will display that change. Gain: Each microphone has an individual gain fader. This fader provides +/- 10dB of gain in 5dB increments.
Revolabs HD Microphones and HD Microphone Adapters Use any of five microphones with your Revolabs HD ™ System: Revolabs HD Wearable Wireless Microphone Revolabs HD Omni-directional Tabletop Wireless Boundary Microphone Revolabs HD Uni-directional Tabletop Wireless Boundary Microphone Revolabs HD Universal Wireless Adapter for Handheld Microphones Revolabs HD Wireless Adapter for Countryman Microphones Using the HD Wearable Wireless Microphones The Revolabs HD Wearable Microphones, shown in the f
3. With the microphone in the wearing position, un-mute the microphone by pressing and releasing the Mute button (confirm by a flashing GREEN LED). If the volume is too low, move the microphone closer to the mouth. 4. To turn microphones off, return the microphone unit to the Charger Base or press and hold the Mute button for ~10 seconds until the LED turns solid RED then release button.
360 º pickup pattern 1 2 3 6 5 4 1. 2. 3. 4. 5. 6. LED display — visual status for mute, un-mute, and pairing. Mute button — press to mute, un-mute and pair microphone. Audio jack — accepts a 2.5mm plug. Charging port — docks to Revolabs HD Charger Bases. Rubber feet — non-slip, vibration absorbing pads. Acoustic Cover — protects delicate microphone element (non-removable). To use the HD Omni Tabletop Microphone: 1. Remove the microphone from the Charger Base to turn on and automatically mute the mic.
If the microphones are placed too far from the Base Station (~150 feet or 50 meters) the connection will be dropped (LED flashes all colors) and the microphone will mute. After 15 seconds the microphone will beep 5 times, and will continue beeping every 30 seconds to indicating it’s out of range. Move the microphone closer to the Base Station and the connection will automatically be re-established to its original state, and the beeping will cease.
3. With the microphone in position, un-mute the microphone by pressing and releasing the Mute button (confirm by a flashing GREEN LED). 4. To turn microphone off, return the microphone unit to the Charger Base or press and hold the Mute button for ~10 seconds until the LED turns solid RED and release button. If the microphones are placed too far from the Base Station (~150 feet or 50 meters) the connection will be dropped (LED flashes all colors) and the microphone will mute.
Note: The Adapter does not provide phantom power or bias current so it cannot be used with condenser or electret microphones. 2. With the microphone attached, un-mute the Adapter by pressing and releasing the Mute button (confirm by a flashing GREEN LED). Note: to use. If the microphone has an on-board mute switch, this switch must also be un-muted prior 3.
2. 3. 4. 5. Charging Port — docks to all Revolabs HD Charger Bases. Mute button — press to mute, un-mute and pair microphone. LED display — visual status for mute, un-mute, and pairing. TA4F connector — connects to Countryman microphone cable. To use the HD Wireless Adapter for Countryman Microphone: 4. Remove the Microphone Adapter from the Charger Base. The adapter turns on and mutes automatically when removed from Charger Base (flashing RED LED).
2. Place the microphone unit into pairing mode by holding the Mute button down for seven seconds. The LED will turn solid RED. Release the Mute button. The microphone is now in pairing mode. 3. Within one minute, push and hold the button for the desired channel on the Base Station for seven seconds until the LED turns solid red then release.
Important: The Lithium Polymer rechargeable batteries that power the microphones were released with both replaceable and non-replaceable type batteries. To distinguish between the 2 different type versions is by serial number only. Serial numbers are located on the label of the back of the microphone itself. Any serial number preference starting with either 7010 or 8020 are equipped with current replaceable rechargeable Lithium Polymer type batteries.
Revolabs HD™ Indicator LEDs The following tables show activities associated with the various states shown by the LEDs: Equipment Use Microphone LED Microphone in Charger Base Microphone not in Charger Base Solid RED Solid GREEN OFF Base Station Channel LEDs OFF OFF OFF Two RED flashes every 1.5 seconds One GREEN flash every 1.5 seconds Solid RED Two RED flashes every 1.5 seconds GREEN flash every 1.
Warranty Revolabs, Inc. warrants this product to be free of manufacturing defects. Repair or replacement of any defective part or unit (at the discretion of the Seller) will be free of charge for the period defined in the Revolabs Professional Products Limited Warranty. Any attempt by the user to alter the equipment, or equipment damaged by negligence, accident, or Acts of God voids this warranty. The Seller shall not be liable for any consequential damage resulting from the malfunction of this product.
Specifications Dimensions, (L, W, H) and Weight: Single/Dual Base Station Single/Dual Charger Base Wireless Microphones Shipping Weight 5.19” (13.18 cm) x 3.25” (8.25 cm) x 1.0” (2.54 cm), 0.325 lbs (0.147 kg) 4.6” (11.75 cm) x 3.125” (7.9 cm) x 1.0” (2.54 cm), 0.325 lbs (0.147 kg Wearable: 0.9” (2.3 cm) x 0.8” (2.0 cm) x 2.6” (6.6 cm), 0.05 lb (0.02 kg) TableTop: 1.5” (3.8 cm) x 0.8” (2.0 cm) x 3.3” (8.4 cm), 0.05 lb (0.02 kg) XLR Adapter: 0.9” (2.3 cm) x 0.8” (2.0 cm) x 4.0” (10.2 cm), 0.05 lb (0.
Index Adjusting the Volume, 14 Base Station, 7 Back Panel, 7 Front Panel, 7 Channel LED indicators, 7 Channels, 8 Charger Bays, 19 Charging the Batteries, 20 First-time use, 20 Recharging, 20 Connections, 8 Earpiece, 8 Full-Duplex, 8 Indicator LEDs, 21 Input Connectors, 8 LED indicator, 19 MC/TDMA/TDD, 6 Microphone Charging port, 13 Earpiece Jack, 13 LED Display, 13 Mute Button, 13 Pocket Clip, 13 Microphones, 12 Pairing, 18 Power Cord Receptacle, 19 Power In Receptacle, 7 Power Module, 20 Safety Informati
Note: Microphones must be fully charged for 8 hours and paired to the Base Station prior to first use. Revolabs HD™ Single & Dual Manual 01-HDSGLMAN-PAP-11 April 2014 (Rev 2.