Wi-Fi Kit Quick Guide V1.
1 Default IP, Username and Password IP address: NVR 192.168.1.30 IPC 192.168.1.13 Username: admin Password: 123456 NOTE! For security, you are strongly recommended to set a strong password of at least nine characters including all three elements: digits, letters and special characters. 2 Disk Installation The illustrations are for reference only. The actual device may vary. 1. Loosen the screws and remove the 2. Secure the disk by fixing the screws cover. to the screw holes shown in the figure.
(Optional) Install SD Card Some camera models support Micro SD card. You need to open the bottom cover to install the SD card. Do not hot plug the Micro SD card after it is inserted. Otherwise the camera or the SD card might be damaged. 1. Open the bottom cover. 2. Insert the SD card properly. Micro SD slot 4 Connect the Kit The following part shows an example. The actual device may vary. 1. Connect the NVR to a monitor with a VGA or HDMI cable (not included in the kit). 2.
IPC Interfaces Antenna Power interface Network interface SD card IP Network 5 Device Operation 5.1 Startup and Shutdown Make sure the cables are connected correctly and the device is grounded properly. Use a power supply that meets requirements. 5.1.1 Startup Connect the devices to power to start up the devices. 5.1.2 Shutdown Click > Shutdown on the screen toolbar in live view page. CAUTION! Do not disconnect power when the NVR is operating or shutting down. 5.
SSID: MAC address by default, you can change as needed. Password: The default is the last eight digits of the serial number. You are strongly recommended to change into a strong password. Region, Channel: Signal interference varies with region and channel. You are recommended to choose a channel with less signal interference. Wireless NIC IP: The IP address of wireless NIC. The NVR assigns IP address to connected devices based on the start and end IP address range.
devices again. Choose one of the following methods as needed. NOTE! The following methods are also applicable if you pair a camera not in the kit with the NVR. One-Click Pair 1. Connect the camera and the NVR to the same switch (or connect the camera to the NVR with a network cable), and connect the devices to power. 2. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP. 3. Press the RESET button on the back of the camera to restore factory default settings.
2. Press the RESET button on the back of the camera to restore factory default settings. 3. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP. 4. Click QR Code Pair, and follow the on-screen instructions to scan the QR code. 5. Wait for the camera to get online. Use EZView Please refer to 8.5 Pair Camera and NVR for detailed steps. 6 Install Devices 6.1 Wi-Fi Signal Connectivity The antenna sends Wi-Fi signals in all directions around it.
Installation with Weakest Signal 6.2 Install the Camera The following part takes wall mount as an example. Make sure the wall is strong enough to support the weight of the camera. Please prepare hardware accessories in advance. 1. Paste positioning stickers on the wall and drill 30mm-depth guide holes using a φ6-6.5mm drill bit. 2. Knock the plastic rivets into the guide holes and ensure that they are tightened up. 3. Screw the locknut to loosen the universal joint, and attach your camera to the wall.
7 Playback In the preview page, select the desired window, then right click and select Playback to play the recording of the current day. NOTE! A 7*24 recording schedule is enabled by default. To set a recording schedule manually, right click and select Menu > Storage > Recording and then set recording type and time based on your needs. If you choose Event type recording, you need to enable the corresponding alarm function and configure alarm-triggered recording/snapshot first.
8.2 Add Devices After logging in to your account, tap > Devices > Add, then select a way to add devices. It’s recommended to choose Scan and scan the QR code on the device body. 8.3 Live View/Playback Tap > Live View/Playback. Tap in a window, then select a device to start live view or playback. You can also tap in the upper-right corner and select device(s). 8.4 Share Devices Tap > Devices, select the desired device and tap Share, then complete the sharing settings.
8.5 Pair Camera and NVR 1. Connect the camera to power, and connect your mobile phone to NVR’s Wi-Fi network. 2. Press the RESET button on the back of the camera to restore factory default settings. 3. Tap > Local Config > Device Wi-Fi Configuration, enter the Wi-Fi password and tap Start to add the camera to the NVR. 9 Web Login Before you begin, check that your PC is connected to your NVR through network. 1. Open the browser on your PC, enter the IP address in the address bar, then press Enter.
Copyright Statement ©2020 REVO AMERICA CORPORATION. All rights reserved. No part of this manual may be copied, reproduced, translated or distributed in any form by any means without prior content in writing from REVO AMERICA CORPORATION (referred to as REVO or us hereafter). The product described in this manual may contain proprietary software owned by REVO and its possible licensors.
To the extent allowed by applicable law, in no event will REVO be liable for any special, incidental, indirect, consequential damages, nor for any loss of profits, data, and documents. The product described in this manual is provided on an "as is" basis.
Disable the automatic login and save password features: If multiple users have access to your computer, it is recommended that you disable these features to prevent unauthorized access. Choose username and password discretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case your social media, bank and email account information is leaked.
Always disconnect the device from power before attempting to move the device. Take proper waterproof measures in accordance with requirements before using the device outdoors. Power Requirements Installation and use of the device must be in strict accordance with your local electrical safety regulations. Use a UL certified power supply that meets LPS requirements if an adapter is used. Use the recommended cordset (power cord) in accordance with the specified ratings.
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.
