Instruction Sheet

System Parts:
(1) Dynamic RF LED Remote Control ............... P/N: L-RGBCCT-RMT
(1) Dynamic RF LED Parent Controller
.............. P/N: L-RGBCCT1-PREC
(1) Dynamic RF LED Child Receiver (optional)
........ P/N: L-RGBCCT1-CREC
(1) Power Supply, Class 2, 12VDC 60W max (or) 24VDC 96W max
Tresco
®
low voltage 12VDC or 24VDC LED RGB or CCT light(s) with Starter Cord
Instructions
FREEDiM Dynamic RF Remote Control
For RGB & CCT LEDs • 12VDC 60W & 24VDC 96W
R
3000K
G
3500K
B
5000K
Z1
Z2
RGB CCT Remote Control
L-RGBCCT-RMT
“On” Indicator Light
CCT Slider
for CCT control
(slide with nger touch)
RGB Color Wheel
for RGB control
(rotate with nger touch)
“On/Off” Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Dim Button
Dims up or down
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
RGB Buttons
Quick preset buttons –
In RGB mode, quickly go to
preset Red, Green or Blue colors
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
CCT Buttons
Quick preset buttons –
In CCT mode, quickly go to preset
Warm (3000K), Neutral (3500K),
or Cool (5000K) light
R
G
B
Z1
Z2
3000K
3500K
5000K
Switch Mode
Switches unit between RGB and
CCT modes
Home Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Takes any settings back to Start
(Starts over at preset settings, but
does not erase pairing)
Speed-up Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Increases the speed of whatever
RGB program running
Play Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Starts the pre-set programs. Hit play
again stops that program. Hit play
again moves to the next program.
Speed-down Button
R
G
B
Z1
Z2
3000K
3500K
5000K
Decreases the speed of whatever
RGB program running
Zone 1 & Zone 2 Buttons
R
G
B
Z1
Z2
3000K
3500K
5000K
R
G
B
Z1
Z2
3000K
3500K
5000K
Switches between Zones 1 and 2
for independent zone functions
The FREEDiM Remote Control starts out with preset settings:
• RGB preset - all values start at 0-0-0
• CCT preset - begins at 2700K
Remote Control Specications:
Operating Voltage: ................ (2) AAA batteries (included)
Radio Frequency: ............. 916.5 MHz
RF Remote Distance: .......... 66 ft. (20m)
RGB and CCT full-function controls:
The Tresco
®
FREEDiM Remote Control provides color and brightness
controls for RGB or CCT (white color-tunable) lighting on Tresco
®
low
voltage LED RGB and CCT lights. It also controls the intensity (dim
levels) of the lights up to 95%. The digital screen on the FREEDiM
Parent Controller displays the current mode and settings.
The wireless Remote Control must be positioned within 66 ft.
(20m) of Parent Controller and any Child Receivers. Note: outside
interference may affect the signal between Remote Control and
Parent Controller. (see ‘Signal Interference’ on page 2)
RGB and CCT modes:
Prior to installation you need to select between RGB or CCT LED
lights. Then after installation, you must select either RGB or CCT
mode on the Parent Controller. (see the Switch Mode button above,
in Fig 1)
See separate instruction sheets for further information on Tresco®
low voltage LED RGB and CCT lights, FREEDiM Parent Controllers
and Child Receivers, and Power Supplies.
Pairing the Remote Control to the Parent Controller
1. First install the Parent Controller with either a RGB or CCT LED light system
and then turn on the Parent Controller.
2. Check the mode on the Parent Controller and select either RGB or CCT mode
depending on the LED light system installed.
3. On the Remote Control hit the ON button
R
G
B
Z1
Z2
3000K
3500K
5000K
.
- The small indicator light in top corner is now red, indicating that the Remote
Control is live and active (this light stays on for 30 sec.) (see Fig. 1 above).
4. Using the Switch Mode button
R
G
B
Z1
Z2
3000K
3500K
5000K
, select either RGB or CCT mode. The red
indicator light underneath the Switch Mode button indicates RGB mode.
5. On the Parent Controller press the Learning Key one time.
6. Next on the Remote Control press the Zone 1 button
R
G
B
Z1
Z2
3000K
3500K
5000K
. The Zone 1 indicator
light underneath is now red (see Fig. 1 above).
7. After you have hit the Zone 1 button, touch either the RGB Color Wheel or
CCT Slider. Lights will ash once indicating everything is paired.
Then repeat steps if adding Zone 2 or more Parent Controllers.
Note: Each zone can control 1 Parent Controller and up to 10 Child Receivers.
Each zone is independent and must be controlled separately from each
other.(see more information and illustration on page 2)
Zone 1 Indicator Light
RGB Indicator Light
#
1
Zone 2 Indicator Light
(Instructions continued on page 2)