RA85 User’s manual
Menu FEATURE.................................................................................... 1 Unpacking and Checking Equipment...................................... 1 Radio Introduction.....................................................................1 Status indication....................................................................... 2 LED Indicator............................................................................. 2 Preparation........................................................
FEATURE • Frequency Range: GMRS •Dual Band, Dual Display, Dual Standby •High Power, middle power, low power switching to meet the different talking distance, save power •Up to 60 memory channels for programming frequency and other various data •Multiple display modes such as channel number, frequency, channel frequency, channel name, etc.
Status Indicator Status Icon NO.
1.Open the earphone cover. 2.Insert the headphone plug into the headphone jack. When you don't need to use the earphones, pull out the earphone plug from the earphone hole and put on the earphone cover. When the universal interface is not used, please put on the dust cover. Do not shake the radio with the top of the antenna, otherwise it will reduce the working performance and service life of the antenna. Radio Charging Note: • Please use the charging equipment designated by our company to charge.
• Channel mode to initiate a call: After selecting a channel, press and hold the [PTT] key to initiate a call to the current channel. Speak into the microphone in a normal tone. When a call is initiated, the red LED light is always on. • Manually input frequency to initiate a call: Press the [V/M] key to switch to frequency mode, enter a frequency within the allowable range, and hold down the [PTT] key to initiate a call to PTT Button Call the current channel. Speak into the microphone in a normal tone.
1 Step 2 Tx Power 3 Power save 4 Vox Level 5 Backlight 6 7 Menu Exit Time Dual Standby 8 Beep Prompt 9 VOICE 10 Tx over time 2.5KHz 5.0KHz 6.25KHz 10.00KHz 12.50KHz 20.0KHz 25.0KHz 50.
18 Scan Mode 19 PTT-ID TO CO SE OFF Time scan Carrier scan Search mode scan Press PTT to not send ID code BOT Press PTT to send ID code (ID code is set by frequency writing software) EOT BOTH 20 MDF-A Frequency Name 21 MDF-B Frequency Name 22 Busy Lockout 23 Key Auto Lock 24 Key1 sp 25 26 27 28 Key1 LP Key2 sp Key2 LP Alarm Mode 29 TAIL 30 PROGER 31 Language Release PTT to send ID code ID code is sent when you press and release the PTT button In the channel mode of the A segment,
32 Reset 33 SPECIAL DCS VFO ALL OFF ON Main Function Description Menu initialization only Menu and channel initialization Turn off special DCS Turn on special DCS,Only the same DCS code can talk to each other The functions supported by the walkie-talkie are shown in the table below. Name Function Description Squelch level Squelch level adjustment is to adjust the signal strength required when receiving signal.
If the dual-standby is enabled on this machine, the VOX function is turned off by default, and the VOX function cannot be activated. Keyboard Lock function The keyboard lock function disables the number keys to prevent you from activating a function by mistake.
Main Technical Specifications Frequency Range Memory channels Frequency step Input voltage Battery(standard configuration) Battery life (5-5-90,high power transmission) Power: Consumption in standby Consumption in reception Consumption in transmission Frequency stability Operating temperature Antenna impedance Dimensions (With battery, but without antenna) Weight (Including antenna and battery) Transmit output power Modulation Spurious emission FM signal-to-noise ratio Audio distortion Modulation limit Adja
CH TX 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 467.5625 467.5875 467.6125 467.6375 467.6625 467.6875 467.7125 462.55 462.575 462.6 462.625 462.65 462.675 462.7 462.725 467.55 467.575 467.6 467.625 467.65 467.675 467.7 467.725 462.5625 462.5875 462.6125 462.6375 462.6625 462.6875 462.7125 467.5625 467.5875 467.6125 467.6375 467.6625 467.6875 467.7125 462.
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 462.575 462.6 462.625 462.65 462.675 462.7 462.725 467.55 467.575 467.6 467.625 467.65 467.675 467.7 467.725 5W 5W 5W 5W 5W 5W 5W 5W 5W 5W 5W 5W 5W 5W 5W 462.575 462.6 462.625 462.65 462.675 462.7 462.725 462.55 462.575 462.6 462.625 462.65 462.675 462.7 462.725 11 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz 12.5KHz D743I D332I 127.3 D243I D606N D731I 136.5 136.5 136.5 136.5 136.5 136.
RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO-WAY RADIOS Before using this radio, read this guide which contains important operating instructions for safe usage and rf energy awareness and control for compliance with applicable standards and regulations. ATTENTION! This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. RF energy, which when used improperly, can cause biological damage.
•This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
•Occupational/Controlled Radio, this radio is designed for and classified as “Occupational/Controlled Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards; NOT intended for use in a General population/uncontrolled environment. •General population/uncontrolled Radio, this radio is designed for and classified as “General population/uncontrolled Use”.
• Use careful with the earphone maybe possible excessive sound pressure from earphones and headphones can cause hearing loss. Note: Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect.
Guarantee Model Number: Serial Number: Purchasing Date: Dealer: Telephone: User’s Name: Telephone: Country: Address: Post Code: Email: Remarks: Please cut along with this line 1.This guarantee card should be kept by the user, no replacement if lost. 2.Most new products carry a two-year manufacturer’s warranty from the date of purchase. Further details, pls read http://www.retevis.com/after-sale/ 3.The user can get warranty and after-sales service as below: • Contact the seller where you buy.
Shenzhen Ysair Technology Co., LTD Add: 6/F, building 6, Yunli intelligent park, No. 3, Changfa Middle Road, Yangmei community, Bantian street, Longgang District, Shenzhen, China Web: www.retevis.com E-mail: kam@retevis.com Facebook: facebook.
说明书要求 尺寸:120*160mm 印刷:黑白印刷 装订:胶订 纸张材质:胶合纸 本页无需印刷