User's Manual

Model: TM101
EU Importer
Name：Germany Retevis Technology GmbH
Address：Uetzenacker 29,38176 wendeburg
※ Display button description：“▲”Up button、“▼”Down button、“■”Function key / shift key、
“●”Reset button / exit button.
※ Remote control button description：Start, time, reset.
※ When the responder is not in use, please turn off the power of the responder through the
back switch to extend the battery life. Please remove the battery when not in use for a long
time.
Answer time-【F1】
1. Press [Function Key ■] to enter the system menu, turn to [F1] and press [Function
Key ■] again to enter the setting mode. The default flashing time will display the
current answering time;
2. Set the answer time by [Up ▲ ▲ / Down ▼], [Function Key ■] Displacement cursor,
the unit is "second", set the range "1-999", short press [Reset button ●] to exit the
setting mode after setting is completed.
3. After the successful answer, press the [Timer] button on the remote control, the
display will display the specified answer time, and start counting down.
Learning number-【F2】
1. Answerer number setting
1) Short press [Function Key ■] to enter the system menu, turn to [F2] and press
[Function Key ■] again to enter the setting mode. The default flashing display
shows “01”;
2) Set the number by [Up ▲/Down ▼], [Function Key ■] Displace the cursor, and set
the range “1-32”. After adjusting to the desired number, press and hold the
responder button for about 2 seconds until the responder flashes. The blue light
starts to match the host code. After the success, the responder flashes red light.
After the setting is completed, press [Reset button ●] to exit the setting mode.
2. Remote control code
1) Short press [Function Key ■] to enter the system menu, turn to [F2] and press
[Function Key ■] again to enter the setting mode. The default flashing display
shows “01” ;
2) Set the number by [Up ▲/Down ▼], [Function Key ■] Displace the cursor, after
adjusting to “00”, press any button of the remote control for 2 seconds or so. After
successful, it will broadcast “Beep” remote control. When the device flashes red,
the code is successful. After setting, press [Reset button ●] to exit the setting mode.
Local ID-【F3】
1. Short press [Function Key ■] to enter the system menu, turn to [F3] and press
[Function Key ■] again to enter the setting mode. The default flashing display shows
“01” ;
2. Set the number by [Up ▲/Down ▼], [Function Key ■] Displace the cursor, set the
range “1-15”, press [Reset Key ●] after setting to exit the setting mode; Note: You
need to relearn the number after changing the ID number. Do not change the local
ID without special circumstances.
Answer mode-【F4】
1. Normal mode-【1】
After pressing the [Start] button, the player directly answers. No 3 seconds
countdown reminder, no voice reminder, and no foul judgment.
1) Short press [Function Key ■] to enter the system menu, turn to [F4] and press
[Function Key ■] again to enter the setting mode. The default flashing mode
displays the current answer mode.
2) Set the number to “1” by pressing [Up ▲/Down ▼], and press [Reset] ● to exit
the setting mode after setting.
2. Voice mode【2】
Press [Start] to start the 3 second countdown, and there is a voice reminder. In 3
seconds, the answer is considered a foul and needs to be restarted.
1) Short press [Function Key ■] to enter the system menu, turn to [F4] and press
[Function Key ■] again to enter the setting mode. The default flashing mode
displays the current answer mode.
2) Set the number to “2” by pressing [Up ▲/Down ▼], and press [Reset] ● to
exit the setting mode after setting.
3. Elimination mode【3】
Press [Start] to start the 3 second countdown, and there is a voice reminder, 3
seconds to answer is considered a foul, but does not affect other players continue
to answer, until someone successfully replies, or everyone fouls, or when the
time is up, the answer is over The winner is a green light, the fouler is a red light,
and the loser does not light up.
1) Short press [Function Key ■] to enter the system menu, turn to [F4] and press
[Function Key ■] again to enter the setting mode. The default flashing mode
displays the current answer mode.
2) Set the number to “3” by pressing [Up ▲/Down ▼], and press [Reset] ● to exit
the setting mode after setting.
Answer time-【F5】
After pressing the [Start Key] 3 seconds countdown, the effective time of the
player's answer is more than the answer time, which is regarded as a waiver.
1) Short press [Function Key ■] to enter the system menu, turn to [F5] and press
[Function Key ■] again to enter the setting mode. The default flashing screen
will display the current answering time;
2) Set the time by the [Up ▲/DOWN] button, the range is “0-999”. After the setting
is completed, press the [Reset button ●] to exit the setting mode.
Set channel-【F6】
Set the communication channel between the responder and the host. When the
responder is not sensitive, try changing the host channel to correct it. After
changing the host channel for 10 seconds, the code responder will flash three
lights and automatically match the host channel. After the match is successful,
the responder light will go out and enter the standby state. If a responder does
not match the host, it will automatically enter the low-power mode. You need to
manually press the responder to wake up and re-match the channel.
1) Press [Function Key ■] to enter the system menu, turn to [F6] and press
[Function Key ■] again to enter the setting mode. The default blinking screen
displays the current channel.
2) Set the time by the [Up ▲/DOWN] button, the range is “0-15”. After the setting
is completed, press the [Reset button ●] to exit the setting mode.
Intelligent
Responder User Manual
1 2
Henan Eshow Electronic Commerce Co., Ltd
Add: 7/F, Sanjiang Building, No.170 Nanyang Road, Huiji District,
Zhengzhou, Henan, China