RTF0B B4T1AL59 9UB
RTF0B4T1AL59UB Table of Contents Feature ...................................................................................................................................................................... 3 Certification(planning) ................................................................................................................................................ 3 Operational ......................................................................................................................
RTF0B4T1AL59UB peripherals, 3 wires Co-exist, 1x IIC,2x ADC, 4wires Feature USART, 2wires UART, high radio performance, output power up to 20dBm and receive sensitivity up to Support RF6 protocol (base on 802.15.4) -105dBm.Working frequency from 2400 to 2480 MHz Support BLE 5.
RTF0B4T1AL59UB Glossary of Terms Terms Description BLE Bluetooth Low Energy UART Universal Asynchronous Receiver Transmitter SPI Serial Peripheral Interface ADC Analog-to-Digital Converter RF Radio Frequency AIO Analog Input / Output GPIO General Purpose Input / Output I2C Inter-Integrated Circuit @2019Resideotechnologylnc..
RT TF0B4T1AL59 9UB 1 Device Overv view RTF0B4 41AL59UB is wireless w modu ule complies with w IEEE802.15.4 and Blue etooth 5.0, sup pport security protocol RF6, BLE5.0 full features, high h speed, lo ong range and ADE, and integrate es rich periphe erals, low power consumption design a wires USART, 2wires UART T, high radio performance, p o output power up u to 20dBm and a 3 wires Co-exist, 1x IIIC,2x ADC, 4w Figure 1-1lists all the key components of the t module.
RTF0B4T1AL59UB Figure 1-2: Thephysicalmapofmodule Table 1-1:Pin Description RTF0B4T1AL59UB Pin Number RTF0B4T1AL59UB Pin Name Description 1 GND Ground 2 ANT1 RF signal antenna 1 3 GND Ground 4 GND Ground 5 debug_uart_TX debug port 6 debug_uart_RX debug port 7 FEM VCC1 Keep float 8 GND Ground 9 coext1 co-exist pin with WiFi&BLE 10 coext2 co-exist pin with WiFi&BLE 11 coext3 co-exist pin with WiFi&BLE 12 Programming when low power up, enter into UART prgram mode 13 GN
RTF0B4T1AL59UB 18 JTAG_TDI GPIO, JTAG_TDO, high-drive capability 19 UART1_RTS UART1 request to send output 20 UART1_CTS UART1 clear to send input 21 GND Ground 22 UART1_TX UART1 Transmit Data output 23 UART1_RX UART1 Receive Data input 24 GPIO1 GPIO 25 SPIFLASH_CS SPI-bus master select output/slave input 26 GND Ground 27 GND Ground 28 VDD Power input 29 VDD Power input 30 GND Ground 31 GND Ground 32 ADC2 ADC input 33 ADC1 ADC input 34 GND Ground 35 nRST r
RTF0B4T1AL59UB 58 GND Ground 59 GND Ground 2 Electrical Performance Table 2-1:Absolute Maximum Ratings Stresses above those listed under “Absolute Maximum Ratings’ may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.
RTF0B4T1AL59UB Total TX/RX Current Parameter Min. Typ. Max. Units 15.4 TX Active @20dBm 1Mbps radio transmitting — 125 — mA 15.4 TX Active @14dBm 1Mbps radio transmitting — 66 — mA 15.4 TX Active @10dBm 1Mbps radio transmitting — 46 — mA 15.4 RX Active — 12.2 — mA BLE TX Active @20dBm 1Mbps radio transmitting — 125 — mA BLE TX Active @14dBm 1Mbps radio transmitting — 66 — mA BLE TX Active @10dBm 1Mbps radio transmitting — 46 — mA BLE RX Active — 12.2 — mA — 2.
RTF0B4T1AL59UB TX_13 Center Freq. Tolerance Error Vector TX_14 Magnitude (EVM) TX_15 RX_10 RX_11 Band edge and Harmonic Receiver sensitivity Receive saturation VCC=3.0,CW, 25°C, 2405MHz, 2440MHz, <40 ppm < 4.5 % 2480MHz According to the standard of IEEE 802.15.4-2011, Charpter 10.3.9 VCC=3.0, OQPSK, 25°C, 2405MHz, 2440MHz, 2480MHz According to the standard of IEEE 802.15.4-2011, Charpter 10.3.8 Output Power = 20dBm under 38% Duty Cycle <51(averge), <71(peak) dBμV/m VCC=3.
RTF0B4T1AL59UB Antennas Current design use external antenna, SATIMO company antenna PN is SD2450, dipole type antenna, the nominal dipole impedance is 50ohm with return loss value better than -15dB at the labeled center frequency and better than -10dB return loss in a bandwidth of 10%. For the more information, please see antenna test report.
RTF0B4T1AL59UB @2019Resideotechnologylnc..
RTF0B4T1AL59UB For the exactly dimension, please see attachment for Gerber files. @2019Resideotechnologylnc..
RTF0B4T1AL59UB @2019Resideotechnologylnc..
RTF0B4T1AL59UB @2019Resideotechnologylnc..
RTF0B4T1AL59UB 3 Mechanical characteristic Table 3-1shows the weight anddimensions.Figure 3-2 shows thephysical dimensions for the RTF0B4T1AL59UBmodule. Table3-2: Mechanical characteristic Specification Dimensions @2019Resideotechnologylnc..16 Description 12x15x2.
RTF0B4T1AL59UB Figure 3-1: RTF0B4T1AL59UBModule Dimensions @2019Resideotechnologylnc..
RTF0B4T1AL59UB @2019Resideotechnologylnc..
RTF0B4T1AL59UB 4 Revision History Revision A (September 2019) This is the initial release of this document FCC Certification Requirements. According to the definition of mobile and fixed device is described in Part 2.1091(b), this device is a mobile device. And the following conditions must be met: 1. This Modular Approval is limited to OEM installation for mobile and fixed applications only.
RTF0B4T1AL59UB 6. The host end product must include a user manual that clearly defines operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. For portable devices, in addition to the conditions 3 through 6 described above, a separate approval is required to satisfy the SAR requirements of FCC Part 2.
