ZRC-100 (Z-Wave Remote Control) 1
Table of Contents Introduction .................................................... 4 Glossary .......................................................... 5 ZRC-100 Operations ....................................... 6 Configurations ................................................. 7 Description of Function Keys .............................. 7 Add/Delete Devices .......................................... 8 Device Control ................................................. 11 Scene Setup ......................
FCC NOTICE .................................................... 52 WARNINGS ...................................................... 52 CAUTION ........................................................
ZRC-100 (Z-Wave Remote Control) Operating Instructions Introduction The ZRC-100 is a LCD Z-Wave remote controller (Figure 1) and it can work with Z-Wave enabled devices, support multi-channel, thermostat, secure door lock, binary / multi-level sensor command class and controls their on/off or up/down individually, or via a pre-configured Scene and adjust your room temperature. The ZRC-100 give an intelligent LEDs smart guide and LCD display for all setup procedures and operation.
Glossary Device or Node Inclusion Exclusion Remove Z-Wave Network Primary Controller Secondary Controller Inclusion Controller Scene Devices and nodes are all terms to describe an individual ZWave device. These are all interchangeable when setting up your ZWave network. Add a Z-Wave device to the network. Delete a Z-Wave device from the network. To take a device out of a group, scene or association group while that device still exists in the same Z-Wave network.
ZRC-100 Operations Welcome to the world of Z-Wave home automation, your ZRC-100 will be able to control all the Z-Wave products around your house. The following section will guide you through the set up processes for your ZRC-100.
Configurations Short cut keys LCD screen BACK key with backlit Arrow + OK keys with backlit Figure 2 Setup and control keys of ZRC-100 Description of Function Keys Keys Functions Short cut keys for device and scene control or jump to corresponding interface Back to previous screen 4-way directional keys for setup and control OK key for confirmation 7
The ZRC-100 remote can be set up with different concepts such as Scene, Association Group, Primary Controller and Secondary Controller. These concepts are all setup on the LCD of your ZRC-100. A single Z-Wave network can include 232 nodes. If necessary, more than one network can be bridged to extend the number of nodes further, although this is normally not needed in a residential environment.
Select “Add Device". 2 Setup Add Device > Delete Device > Add to Scene > OK to Enter Add Device 3 key to add Press the device into Z-Wave network. Press the program button on the target device. Press PROG on target >>>> Add Device Press PROG on target >>>> Saving Data … ⇓ 4 Add Device Press PROG on target >>>> OK Note 1: If you can’t add your Z-Wave device, this device might have been included in another Z-Wave network.
Deleting Device from the Network Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Delete Device". Setup 2 Add Device > Delete Device > Add to Scene > OK to Enter Delete Device 3 key to delete Press the device from Z-Wave network. Press the program button on the target device.
Note 1: If no ACK signal received for more than 60 seconds, the “Delete Device” mode will exit automatically. Device Control After adding devices to your ZRC-100, you can turn the device on/off or up/down via the corresponding Device Control function. Step Setup Key LCD Indication Select “Device"and key to entry press the Device control page under Home page.
You can turn off all the devices in the network by selecting “All Off" function under Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 4 Home Sensor > All Off OK to Enter Note 1: The screen will display LOCK /UNLK if this is a secure door lock device. Scene Setup Z-Wave Scenes are used for setting up multiple devices in a scene. You can set to different levels depending on the situation.
Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Add to Scene" and press key. 2 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select a Scene which you want to add the device into Scene and Select Scene Scene 1 Scene 2 3 press Scene 3 key. OK to Enter Press the program button on the target device.
Note 2: If no ACK signal received for more than 60 seconds, the “Add Device” mode will exit automatically. Removing Device/End-point from a Scene Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Remove from 2 Scene"and press key. Setup Remove fr. Scene > Device Config. > Scene Config.
Remove Device Press PROG on target >>>> OK Note 1: This process will only remove the target device/EP from its assigned scene but will not exclude it from the network. Note 2: If no ACK signal received for more than 60 seconds, the “Remove Device” mode will exit automatically. Scene Control After the scene setup is done, you can trigger the desired scene via scene control function on ZRC-100.
Comfort Control After adding “Thermostat" or “Z-Wave to AC IR extender" to your ZRC-100, you can change the operation mode, set target temperature and fan speed via the corresponding Comfort Control function. Step Setup Key LCD Indication Select “Comfort"and key to entry press the Comfort control page under Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Comforts List Thermostat 003 > OK to Enter Select your Thermostat 2 and press key to entry the Thermostat control page.
Sensor information After adding “Binary Sensor / Multi-level Sensor"to your ZRC-100, you can monitor the sensor temperature via the corresponding Sensor function. Step Setup Key LCD Indication Select “Sensor"and Home Sensor key to entry press the Sensor page under Home page. > All Off OK to Enter ⇓ 1 Sensors List Sensor 003 75 Device Configure It is allow to Move/Rename/Delete the device after added into the network under the Device Configure function.
Select “Device Configure"and press 2 Setup Remove fr. Scene key. > Device Config. > Scene Config. > OK to Enter Select your“Device" and press key. 3 Device Configure Dimmer 002 > Dimmer 004 > OK to Enter Select your action (e.g. 4 Edit Move Move) and press key. Rename Delete OK to Execute Move your selected device to your target Move position and press to save the setting.
Use cdkeys to change your character and ef keys to select character position, press save the setting. Rename Dimmer 002 to OK to Save ⇓ 7 Rename Bedroom OK to Save Select your action (e.g. 8 Edit Move Delete) and press key. Rename Delete OK to Execute 9 Press f key to confirm to delete the selected device or press e key to cancel it and go back to previous page. Delete Dimmer 002 e NO Confirm? YES f Note 1: ZRC-100 supports up to 16 characters in a row for the device name.
⇓ Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Scene Configure"and press 2 Setup key. Remove fr. Scene > Device Config. > Scene Config. > OK to Enter Select your“Scene" Scene Configure Scene 1 and press key. Scene 2 3 Scene 3 OK to Enter Select your action (e.g. 4 Edit Move Move) and press key. Rename Clear OK to Execute Move your selected scene to your target Move Scene 1 Scene 2 position and press to save the setting.
Select your action (e.g. Rename) and press 6 Edit Move Rename key. Clear OK to Execute Use cdkeys to change your character and ef keys to select character position, press save the setting. Rename Scene 1 to OK to Save ⇓ 7 Rename Back to Home OK to Save Select your action (e.g. 8 Edit Move Clear) and press key. Rename Clear OK to Execute 9 Press f key to confirm to clear the selected scene or press e key to cancel it and go back to previous page.
Comfort / Sensor Configure It is allow to Move/Rename/Delete the device after added into the network under the Comfort / Sensor Configure function. Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Comfort Configure"and press 2 Setup key. Comfort Config. > Sensor Config.
Move your selected Thermostat to your target position and press Move Thermostat 003 Thermostat 005 to save the setting. OK to Save ⇓ 5 Move Thermostat 005 Thermostat 003 OK to Save Select your action (e.g. Rename) and press 6 Edit Move Rename key. Delete OK to Execute Use cdkeys to change your character and ef keys to select character position, press save the setting. Rename Thermostat 003 to OK to Save ⇓ 7 Rename Bedroom OK to Save Select your action (e.g.
9 Press f key to confirm to delete the selected thermostat or press e key to cancel it and go back to previous page. Delete Thermostat 003 e NO Confirm? YES f Note 1: ZRC-100 supports up to 16 characters in a row for the scene name. Shortcut key ZRC-100 provides a shortcut key which can jump to your target Comfort / Sensor device or turn On/Off your device/ Scene. Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page.
4 Select your target Device / Scene / All Off for your shortcut key or Select your target shortcut page (Comfort / Sensor) for your shortcut key. Select a Device or Scene to this shortcut key then 5 press Select Device > Scene > Comfort > OK to Enter Select Switch 001 Dimmer 002 key. OK to Save key to turn Press On your Device or Scene at any page or 6 Press and hold key to turn Off your Device or Scene at any page.
Z-Wave Advanced Setup Learning Mode (Replicating All Network and Device Information from a Primary Controller to your ZRC-100) Your ZRC-100 can: • Copy the settings from another Z-Wave controller. • Be included into existing Z-Wave network and become a secondary remote controller or back to a new primary remote controller. • Be excluded from the Z-Wave network. Step Setup Key LCD Indication 1 Place the two controllers close to each other. - Press and hold ef keys for 3 seconds under the Home page.
information. (Refer to the primary controller user manual for more information) Place the two controllers close to each other. 5 (LCD display OK if the learning mode is successful. LCD display ERROR if the learning mode is unsuccessful.
Configure Association (Assign Association for Two Devices) The ZRC-100 can be used to assign one device to automatically interact directly with another device. For example you can assign a door sensor (primary node) to turn on the light switch (secondary node) when the door is opened. Adding Device/End-point to an Association Group Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page.
Assign an “Assoc. ID" (e.g. 001) by using cdkeys to change your number and ef keys to select number position. Add Assoc. Assoc. ID (1-255) 000 OK to Save 5 key to save Press the settings. ⇓ Add Assoc. Assoc. ID (1-255) 001 OK to Save Press the program/EP button on the secondary device (e.g. light switch) Add Assoc. Press PROG on Sec. >>>> e.g. light switch ⇓ 6 Add Assoc. Press PROG on Sec. >>>> e.g. light switch OK Press the program/EP button on the primary device (e.g.
Note 1: Your target device must be included in the network before this setup procedure, please refer to [Adding Device to the Network] section. Removing Device/End-point from an Association Group Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Advanced 2 Setup Setup"and press key.
Select an “Assoc. ID" (e.g. 001) by using cdkeys to change your number and ef keys to select number position. Remove Assoc. Assoc. ID (1-255) 000 OK to Save 5 key to save Press the settings. ⇓ Remove Assoc. Assoc. ID (1-255) 001 OK to Save Press the program/EP button on the secondary device (e.g. light switch) Remove Assoc. Press PROG on Sec. >>>> e.g. light switch ⇓ 6 Remove Assoc. Press PROG on Sec. >>>> e.g. light switch OK Press the program/EP button on the primary device (e.g.
Note 1: This process will only remove the target device/EP from its assigned association group but will not exclude it from the network. Deleting an Association Group Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Advanced 2 Setup Setup"and press key.
Select an “Assoc. ID" (e.g. 001) by using cdkeys to change your number and ef keys to select number position. Delete Assoc. Assoc. ID (1-255) 000 OK to Save 5 key to save Press the settings. ⇓ Delete Assoc. Assoc. ID (1-255) 001 OK to Save Press the program/EP button on the primary device (e.g. door sensor) Delete Assoc. Press PROG on Pri. >>>> e.g. door sensor ⇓ 6 Delete Assoc. Press PROG on Pri. >>>> e.g.
Change Device Configuration This function is used to modify the parameter of the Z-Wave device via the configuration command class. Look up the Parameter No. and Parameter Value of the target device from the device user manual before you start the below process. Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page.
Use cdkeys to change your parameter value and ef keys to select number position, press 5 to save the setting. Configuration Parameter Value +0000000000 OK to Save (Parameter value from 2147483648 to +2147483647 (32bits value) Press the program button on the target device.
Resetting Your Network You can reset your ZRC-100 to clear all Z-Wave network and device information by the following steps: Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “Advanced 2 Setup Setup"and press key.
Reset to Default Under progress ..... Waiting ⇓ Reset to Default Successful! OK Note: After reset the remote, each device should individually perform in the section on “Delete device from the network” and “Add device to the network”. System Settings Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page.
Select “LCD Contrast "and press 3 System Settings LCD Contrast B.L. Brightness key. Sleep Timer OK to Enter Press ef keys to adjust the LCD contrast. LCD Contrast 50 % - 4 + e Control f 5 Press key to save and return to previous page then select “B.L. Brightness"and press System Settings LCD Contrast B.L. Brightness Sleep Timer OK to Enter key. 6 Press ef keys to adjust the backlight brightness. B.L.
About ZRC-100 Step Setup Key LCD Indication Press and hold ef keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Setup Add Device > Delete Device > Add to Scene > OK to Enter Select “About"and Setup key. It will press show the firmware version on the screen. Advanced Setup > System Settings > About > OK to Enter ⇓ 2 About Remotec Technology Host FW Ver. : 1.
Z-Wave Network Setup Rediscover Network (N.W.) During normal operation the network decides the best path to route signals from one device to another. If devices are moved to different positions in the installation, it is recommended to rediscover the network so the routing path will be re-configured. Step Setup Key LCD Indication Press and hold cb keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Network Setup Rediscover N.W.
Re-scan (Rediscover) Devices from network In most cases, your home Z-Wave gateway will become a primary controller (control center), all Z-Wave devices will be added / (inclusion) by the Z-Wave gateway. Normally, it is need to click the PROG button of the Z-Wave device to add into the network and one by one. The gateway will create a control page / section to Z-Wave devices. User can control / monitor Z-Wave devices under the control page.
Press f key to confirm re-scan devices or press e key to cancel it and go back to previous page. Re-scan Devices Caution! This action will wipe out all existing device names e NO 3 The remote will re-scan all devices from network, discovered devices will be reassigned to their default categories (Devices, Comforts and Sensors) names will be reassigned in ascending order. The LCD will display OK and go back to previous page when it is completed. This action may take several minutes.
Delete Dead Node from Network Step Setup Key LCD Indication Press and hold cb keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 1 Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Delete Dead 2 Network Setup Node” and press key. Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter The remote is checking the dead node.
Use cb keys to select the dead node device Dead Node Dimmer 002 key to then press delete it from network. OK to Delete ⇓ 4 Dead Node OK Note 1: Only the Primary Controller can be used to include or delete devices from a network. It is recommended that you mark the primary controller for each network for ease in modifying your network.
Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Listening Mode” and press key. 3 Network Setup Listening Mode > Create a Sec. > Create a Pri > OK to Enter 4 The remote is entry the listening mode. (Listening mode will automatically exit after 1 minute of inactivity.) Listening Mode Listening… >>>> Note1: The mode must not be exited during communication process with another controller.
⇓ Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Create a Sec.” then press Network Setup key. 3 Listening Mode > Create a Sec. > Create a Pri > OK to Enter 4 Please make sure the target secondary controller is setup to receive information mode. (e.g. target secondary controller should entry the “Learning mode" if this is a another ZRC100.
Step Setup Key LCD Indication 1 Place the two controllers close to each other. - Press and hold cb keys for 3 seconds under the Home page. Home Device > Scene > Comfort > OK to Enter ⇓ 2 Network Setup Rediscover N.W. > Re-scan Devices > Delete Dead Node > OK to Enter Select “Create a Pri.” then press Network Setup key. 3 Listening Mode > Create a Sec. > Create a Pri > OK to Enter 4 Please make sure the target primary controller is setup to receive information mode. (e.g.
WIRELESS INFORMATION Wireless range: This device has an open air line of sight transmission distance of 100 feet which complies with the Z-Wave standards. Performance can vary depending on the amount of objects in between Z-Wave devices such as walls and furniture. Every Z-Wave device set up in your house will act as a signal repeater allowing devices to talk to each other and find alternate routes in the case of a reception dead spot. Radio frequency limitations: 1. Each wall or object (i.e.
Q A What can the Remotec ZRC-100 do for me? A single Z-Wave network can include 232 nodes. If necessary, more than one network can be bridged to extend the number of nodes further, although this is normally not needed in a residential environment. The total number of controllable End-point (EP) / device / sensor is 128 items which is listed on the “Device” and “Sensor” page. ZRC-100 also supports 6 thermostats which are listed on the “Comfort” page.
Please refer to the target device user manual for more information such as Inclusion / Exclusion and add End Point to a Scene / Group. Q A Why do I need a different module for outdoor lighting? The outdoor module is designed to withstand various weather conditions including heat, rain and snow. Q Can I use 2 or more ZRC-100 controllers in my house at one time? You can use multiple ZRC-100 around your house by assigning one remote to be the primary remote and have an additional secondary controller.
TECHNICAL SPECIFICATIONS Model No. BW8380US (ZRC-100US) Model No. BW8380EU (ZRC-100EU) Model No. BW8380AU (ZRC-100AU) Model No. BW8380IN (ZRC-100IN) RF Frequency 908.4MHz (US) RF Frequency 868.4MHz (EU) RF Frequency 921.4MHz (AU) RF Frequency 865.2MHz (IN) LCD FSTN Positive Transflective 128x64 dots at A.A.= 35.8x21.7mm LCD and key pad backlight color Amber Max.
COMMAND_CLASS_THERMOSTAT_FAN_MODE YES NO COMMAND_CLASS_SENSOR_BINARY YES NO COMMAND_CLASS_SENSOR_MULTILEVEL YES NO COMMAND_CLASS_CONTROLLER_REPLICATION NO YES COMMAND_CLASS_ASSOCIATION YES YES COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION YES YES COMMAND_CLASS_VERSION NO YES COMMAND_CLASS_CONFIGURATION YES NO COMMAND_CLASS_MANUFACTURER_SPECIFIC NO YES COMMAND_CLASS_WAKE_UP NO YES COMMAND_CLASS_DOOR_LOCK YES NO COMMAND_CLASS_SECURITY YES YES CHECKING THE ACCESSORIES After openin
then the controlled appliances, also an unintentional activation may occur if the wrong button on the remote is pressed. Z-Wave devices may automatically be powered on due to timed event programming. Depending upon the appliance, these unattended or unintentional operations could possible result in a hazardous condition.