It’s Under Control ® M2 Operation Guide Professional Capture System Universal Infrared SystemCode Controller © 2007 Remote Technologies Inc. All rights reserved. Printed in Taiwan. IR-PRO M2 7651 Anagram Drive Eden Prairie, MN 55344 Tel: 952-253-3100 Fax: 952-253-3131 www.rticorp.com IR-PRO Remote Technologies Incorporated Professional Infrared Code Capture System v1.
FEDERAL COMMUNICATIONS COMMISSION NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
M2 Universal System Controller BATTERY DISPOSAL This product is shipped with non-rechargeable alkaline batteries. These batteries are generally considered not to be environmentally hazardous. In most cases they can be disposed of in normal household trash, but you should always verify and follow your local regulations. Do not burn or incinerate used batteries, as it may cause internal materials to explode. It is important not to dispose of large amounts of alkaline batteries in a group.
LIMITED WARRANTY Remote Technologies Incorporated warrants its products for a period of one (1) year (does not apply to included batteries) from the date of purchase from Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor. This warranty may be enforced by the original purchaser and subsequent owners during the warranty period, so long as the original dated sales receipt or other proof of warranty coverage is presented when warranty service is required.
M2 Universal System Controller If your M2 needs service, please contact Remote Technologies Incorporated by telephone, fax or e-mail for return information. Please do not authorization. return products to RTI without return DISCLAIMER All rights are reserved. No part of this document may be photocopied, reproduced, or translated without the prior written notice of Remote Technologies Incorporated. The information contained in this document is subject to change without notice.
Contents Federal Communications Commission Notice ---------------------- i Battery Disposal ----------------------------------------------------------- ii Safety Suggestions -------------------------------------------------------- ii Limited Warranty -------------------------------------------------------- iii Disclaimer-------------------------------------------------------------------iv Contents------------------------------------------------------------------------ v Chapter 1.
M2 Universal System Controller Clear All ----------------------------------------------------------------- 14 Low Battery Indicator --------------------------------------------------- 15 Programming The M2--------------------------------------------------- 15 Chapter 4.
Chapter 1. Welcome Thank you for purchasing the M2 universal system controller. The M2 combines the power and flexibility of a graphic LCD display with an ergonomic design that permits effortless one-handed operation. This design overcomes the need for a compromise between form and function. Sleek and perfectly balanced, the M2 is infinitely flexible and expandable. The M2 takes complete control of your home electronics, replacing all other remotes.
M2 Universal System Controller UNPACKING AND INSPECTION After unpacking your new M2 universal system controller, save all of the packing materials in case you ever have to ship the unit. Thoroughly inspect the M2 and packing materials for signs of damage. Report any damage to the carrier immediately. Report any equipment malfunctions to Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor.
Chapter 2. Introduction FEATURES The M2 provides superior quality and reliability as well as these specific features: § Replaces all of the remote controls in a home. The M2 can reproduce all of the commands of almost any other infrared remote control. § A programmable graphic display. The M2 uses powerful Windows® based software that makes it easy to place text, graphics, symbols and icons anywhere on the display. § A wide temperature, high-contrast LCD with white backlight.
M2 Universal System Controller § A USB port for communication with the TheaterTouch Designer programming software. § Non-volatile flash memory. The M2 will not lose any programmed data when the battery is removed. § One-year parts and labor warranty. § Available only to system integration professionals. IMPORTANT NOTES Please read these important notes about the M2: § The M2 should be placed in an area where it is around normal room temperature (between 60°F to 90°F).
Introduction GETTING STARTED Start by inserting four AAA batteries (included) into the battery compartment. Make sure they are oriented properly. A polarity diagram is molded into the bottom of the battery compartment. + + The M2 is turned-on by touching any keypad button. If the tilt sensor is enabled, picking up the unit will also turn it on.
M2 Universal System Controller REMOTE REFERENCE IR Transmission Window Front LCD Display Display “Soft” Buttons Home Page Button Page Navigation Buttons Backlight Button 6 Keypad Buttons
Introduction Back Audio Beeper Battery Compartment USB Programming Port 7
M2 Universal System Controller 8
Chapter 3. Operation THE LCD DISPLAY The M2 display is organized as a series of pages and frames. A page consists of one to nine frames, and only one frame is displayed on the screen at a time. Normally each frame on a page contains objects (text, graphics, etc.) that are related in some way. For instance, they may all display information necessary for controlling a particular DVD player. By default, the M2 has one Home page—all other pages are normally accessed from links on the Home page.
M2 Universal System Controller THE CONTROL PANEL PAGE The Control Panel page can be displayed by pressing and holding the backlight button continuously for 3 seconds. You can also access the Control Panel page by assigning a “Control Panel” page link to a button using the TheaterTouch Designer software. The Control Panel consists of the following two frames: To change frames, press the next page button below the display. To return to the user program, press the Home button.
Operation ADJUST CONTRAST This selection displays a window that allows you to adjust the LCD contrast. Press the Left Arrow or Right Arrow soft buttons to adjust. Press either of the OK soft buttons to close. BEEPER This selection displays a window that allows you to turn the audible beep on or off. The beeper provides feedback that a button was pressed. Press either of the OK soft buttons to close.
M2 Universal System Controller TILT SWITCH This selection displays a window that allows you to adjust the settings for the built-in tilt switch. The tilt switch is a motion detector that turns the remote on when activated. On means the tilt switch is active and will wake up the M2 when it is moved. Off means the tilt switch is inactive. Press either of the OK soft buttons to close.
Operation Now enter a new four-digit passcode. You will be prompted to enter the new four-digit passcode again for confirmation. When new code is entered successfully, the “Code Changed” window will pop up to let you know you have changed the passcode.
M2 Universal System Controller CLEAR ALL This selection displays a window that will allow you to erase the current user program in the M2. You will be prompted to enter the current passcode. If the proper code is entered, the entire user program in the M2 will be erased. Warning! This will erase the entire user program in the M2.
Operation LOW BATTERY INDICATOR If the M2 battery capacity is reduced to approximately 25 percent, a low battery icon will appear in the lower left side of the display: Low Battery Icon At this point the M2 batteries should be replaced to maintain optimum performance. PROGRAMMING THE M2 The M2 is programmed using RTI’s TheaterTouch Designer software. RTI dealers can download the software free of charge from: www.rticorp.com/dealers A PC running Windows® 98SE or higher with a USB port is required.
M2 Universal System Controller Note: The M2 will not operate normally while connected to a PC’s USB port. Make sure you disconnect it from the PC to navigate pages or transmit commands. In addition, the M2 will not be able to sync with a PC’s USB port while it is transmitting a command or running a macro.
Chapter 4. Troubleshooting If you are having problems with your M2, please read these troubleshooting tips before contacting technical support. If you continue to have problems, see Chapter 5 for more information on contacting RTI technical support. DISPLAY IS DIM, BLANK OR UNREADABLE Make sure the batteries are inserted properly and are new. Try adjusting the contrast level from the Control Panel page (Refer to Chapter 3 for more details).
M2 Universal System Controller If you are still having problems, try adjusting the IR code “Minimum Repeats” value in the TheaterTouch Designer programming software. If the IR code is executed inside a macro that contains multiple IR codes, try inserting a small time delay before the problem code. If there already is a delay, try increasing it.
Chapter 5. Service and Support UPDATES AND NEW PRODUCTS For news about the latest updates, new product information and accessories, please visit our web site at: www.rticorp.com CONTACTING REMOTE TECHNOLOGIES INCORPORATED For general info, you can contact RTI at: Remote Technologies Incorporated Tel. (952) 253-3100 Fax (952) 253-3131 info@rticorp.com www.rticorp.com RTI TECHNICAL SUPPORT At RTI, customer service and satisfaction is an utmost priority.
M2 Universal System Controller If you are having a problem with hardware, please note the equipment in your system, a description of the problem, and any troubleshooting you have already tried. If you are having a problem with software, please note what version you have installed, the operating system on your PC, a description of the problem, and any troubleshooting you have already tried.
Specifications Power 4 AAA alkaline batteries Power Management Automatic On/Off (tilt switch) Infrared Control Range 30 Feet (9.1m) @ 60 Degrees Infrared Frequency Range 15kHz – 460kHz Radio Frequency Control Range Up to 100 Feet (30.5m) (with optional receivers) Radio Frequency Carrier 433MHz Operating Temperature +32°F to +122°F (+0°C to +50°C) Operating Humidity 5% to 95% Non-condensing Display High-contrast transflective monochrome STN LCD 128h x 64w pixels Display size (H x W) 2.
M2 Universal System Controller Macro Capability Unlimited steps in a single macro Total number of macros limited only by memory Macros allowed on every button Communications USB programming port Dimensions Length: 9.1 in. (251mm) Width: 2.4 in. (64mm) Height: 1.1 in. (28mm) Enclosure High-impact molded ABS plastic Weight 7.0 oz. (200g) with batteries Warranty One Year Parts & Labor (30 days on batteries) All specifications are subject to change without notice.
It’s Under Control ® M2 Operation Guide Professional Capture System Universal Infrared SystemCode Controller © 2007 Remote Technologies Inc. All rights reserved. Printed in Taiwan. IR-PRO M2 7651 Anagram Drive Eden Prairie, MN 55344 Tel: 952-253-3100 Fax: 952-253-3131 www.rticorp.com IR-PRO Remote Technologies Incorporated Professional Infrared Code Capture System v1.