It’s Under Control ® T2+ Operation Guide Professional Capture System Universal Infrared SystemCode Controller © 2004 Remote Technologies Inc. All rights reserved. Printed in Taiwan. IR-PRO T2+ 18681 Lake Drive East Chanhassen, MN 55317 Tel: 952-253-3100 Fax: 952-253-3131 www.rticorp.com IR-PRO Remote Technologies Incorporated Professional Infrared Code Capture System v1.
FEDERAL COMMUNICATIONS COMMISSION NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
T2+ Universal System Controller BATTERY DISPOSAL Li-ion For environmental reasons, your T2+ universal system controller uses “environmentally sound” Lithium-ion rechargeable batteries. These batteries do not contain any poisonous heavy metals that can damage the environment. In the interest of recycling, please do not dispose of these batteries in the household waste at the end of their useful life. Instead, dispose of them at an appropriate collection site. SAFETY SUGGESTIONS Read Instructions.
T2+ Universal System Controller Nominal Run Time on Full Charge 5 hours continuous use (10 - 15 days average use) Standby Time on Full Charge 30 Days Battery Charge Time 3-4 Hours Total System Memory 256K Bytes Flash (non-volatile) Device Capability Total number of devices limited only by memory Macro Capability Up to 64 steps per macro Total number of macros limited only by memory Macros allowed on every button Communications USB programming port Dimensions Length: 9.9 in. (251mm) Width: 2.
T2+ Universal System Controller Remote Technologies Incorporated is not liable for any damages caused by its products or for its failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages. Specifications Power 3.6 VDC, 1050 mAH Li-Ion Battery Pack Power Management Automatic On/Off (tilt switch) Infrared Control Range 30 Feet (9.1m) @ 60 Degrees Infrared Frequency Range 15kHz – 460kHz Radio Frequency Control Range Up to 100 Feet (30.
T2+ Universal System Controller If you are having a problem with hardware, please note the equipment in your system, a description of the problem, and any troubleshooting you have already tried. If you are having a problem with software, please note what version you have installed, the operating system on your PC, a description of the problem, and any troubleshooting you have already tried.
T2+ Universal System Controller Clear all ------------------------------------------------------------------ 14 Chapter 5. Service and Support Programming The T2+ -------------------------------------------------- 14 Chapter 4.
T2+ Universal System Controller If you are still having problems, try adjusting the IR code “Minimum Repeats” value in the TheaterTouch Designer programming software. If the IR code is executed inside a macro which contains multiple IR codes, try inserting a small time delay before the problem code. If there already is a delay, try increasing it. Chapter 1. Welcome Thank you for purchasing the T2+ universal system controller.
T2+ Universal System Controller UNPACKING AND INSPECTION Chapter 4. Troubleshooting After unpacking your new T2+ universal system controller, save all of the packing materials in case you ever have to ship the unit. Thoroughly inspect the T2+ and packing materials for signs of damage. Report any damage to the carrier immediately. Report any equipment malfunctions to Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor.
T2+ Universal System Controller CLEAR ALL This button displays a window that will allow you to erase the current user program in the T2+. When the button is pressed, you will be prompted to enter the current passcode. If the proper code is entered, the entire user program in the T2+ will be erased. Chapter 2. Introduction FEATURES The T2+ provides superior quality and reliability as well as these specific features: ! A replacement for all of the remote controls in a home theater.
Operation T2+ Universal System Controller ! A built in motion sensor can automatically turn the unit on when it is picked up. ! A USB port for communication with the TheaterTouch Designer programming software. ! Non-volatile flash memory. The T2+ will not lose any programmed data when the battery is removed. ! One-year parts and labor warranty ! Available only to system integration professionals. IMPORTANT NOTES Now enter a new four-digit passcode.
T2+ Universal System Controller Introduction TILT SWITCH CLEANING This button displays a window that allows you to adjust the settings for the built-in tilt switch. The tilt switch is a motion detector that turns the remote on when activated. Occasional cleaning may be required, depending on use. It is recommended that you create a “Clean” button somewhere on the Home page of the T2+.
T2+ Universal System Controller Operation If the T2+ battery capacity is reduced to approximately one hour of remaining run-time, a low battery icon will appear in the upper left corner of the display: The docking station LED illuminates to indicate a charge in progress. The LED will turn off when the battery in the unit is fully charged. A fully discharged battery will take approximately 2-4 hours to completely re-charge.
T2+ Universal System Controller Introduction By default, pressing the HOME button at any time will return you to this page. It is possible, however, to program the Home button to behave differently if desired. REMOTE REFERENCE IR Transmission Window THE CONTROL PANEL PAGE The Control Panel page can be displayed by pressing and holding the backlight button continuously for 3 seconds.
T2+ Universal System Controller DOCKING STATION REFERENCE Chapter 3. Operation Front THE TOUCHSCREEN DISPLAY The T2+ touchscreen display is organized as a series of pages and frames. A page consists of one to twelve frames, and only one frame is displayed on the screen at a time. Charge Contacts Normally each frame on a page contains objects (buttons, text, graphics, etc.) that are related in some way. For instance, they may all display information necessary for controlling a particular DVD player.
T2+ Universal System Controller DOCKING STATION REFERENCE Chapter 3. Operation Front THE TOUCHSCREEN DISPLAY The T2+ touchscreen display is organized as a series of pages and frames. A page consists of one to twelve frames, and only one frame is displayed on the screen at a time. Charge Contacts Normally each frame on a page contains objects (buttons, text, graphics, etc.) that are related in some way. For instance, they may all display information necessary for controlling a particular DVD player.
T2+ Universal System Controller Introduction By default, pressing the HOME button at any time will return you to this page. It is possible, however, to program the Home button to behave differently if desired. REMOTE REFERENCE IR Transmission Window THE CONTROL PANEL PAGE The Control Panel page can be displayed by pressing and holding the backlight button continuously for 3 seconds.
T2+ Universal System Controller Operation If the T2+ battery capacity is reduced to approximately one hour of remaining run-time, a low battery icon will appear in the upper left corner of the display: The docking station LED illuminates to indicate a charge in progress. The LED will turn off when the battery in the unit is fully charged. A fully discharged battery will take approximately 2-4 hours to completely re-charge.
T2+ Universal System Controller Introduction TILT SWITCH CLEANING This button displays a window that allows you to adjust the settings for the built-in tilt switch. The tilt switch is a motion detector that turns the remote on when activated. Occasional cleaning may be required, depending on use. It is recommended that you create a “Clean” button somewhere on the Home page of the T2+.
Operation T2+ Universal System Controller ! A built in motion sensor can automatically turn the unit on when it is picked up. ! A USB port for communication with the TheaterTouch Designer programming software. ! Non-volatile flash memory. The T2+ will not lose any programmed data when the battery is removed. ! One-year parts and labor warranty ! Available only to system integration professionals. IMPORTANT NOTES Now enter a new four-digit passcode.
T2+ Universal System Controller CLEAR ALL This button displays a window that will allow you to erase the current user program in the T2+. When the button is pressed, you will be prompted to enter the current passcode. If the proper code is entered, the entire user program in the T2+ will be erased. Chapter 2. Introduction FEATURES The T2+ provides superior quality and reliability as well as these specific features: ! A replacement for all of the remote controls in a home theater.
T2+ Universal System Controller UNPACKING AND INSPECTION Chapter 4. Troubleshooting After unpacking your new T2+ universal system controller, save all of the packing materials in case you ever have to ship the unit. Thoroughly inspect the T2+ and packing materials for signs of damage. Report any damage to the carrier immediately. Report any equipment malfunctions to Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor.
T2+ Universal System Controller If you are still having problems, try adjusting the IR code “Minimum Repeats” value in the TheaterTouch Designer programming software. If the IR code is executed inside a macro which contains multiple IR codes, try inserting a small time delay before the problem code. If there already is a delay, try increasing it. Chapter 1. Welcome Thank you for purchasing the T2+ universal system controller.
T2+ Universal System Controller Clear all ------------------------------------------------------------------ 14 Chapter 5. Service and Support Programming The T2+ -------------------------------------------------- 14 Chapter 4.
T2+ Universal System Controller If you are having a problem with hardware, please note the equipment in your system, a description of the problem, and any troubleshooting you have already tried. If you are having a problem with software, please note what version you have installed, the operating system on your PC, a description of the problem, and any troubleshooting you have already tried.
T2+ Universal System Controller Remote Technologies Incorporated is not liable for any damages caused by its products or for its failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages. Specifications Power 3.6 VDC, 1050 mAH Li-Ion Battery Pack Power Management Automatic On/Off (tilt switch) Infrared Control Range 30 Feet (9.1m) @ 60 Degrees Infrared Frequency Range 15kHz – 460kHz Radio Frequency Control Range Up to 100 Feet (30.
T2+ Universal System Controller Nominal Run Time on Full Charge 5 hours continuous use (10 - 15 days average use) Standby Time on Full Charge 30 Days Battery Charge Time 3-4 Hours Total System Memory 256K Bytes Flash (non-volatile) Device Capability Total number of devices limited only by memory Macro Capability Up to 64 steps per macro Total number of macros limited only by memory Macros allowed on every button Communications USB programming port Dimensions Length: 9.9 in. (251mm) Width: 2.
It’s Under Control ® T2+ Operation Guide Professional Capture System Universal Infrared SystemCode Controller © 2004 Remote Technologies Inc. All rights reserved. Printed in Taiwan. IR-PRO T2+ 18681 Lake Drive East Chanhassen, MN 55317 Tel: 952-253-3100 Fax: 952-253-3131 www.rticorp.com IR-PRO Remote Technologies Incorporated Professional Infrared Code Capture System v1.