User's Manual

Enjoy your
XFINITY® TV
right away!
Program your remote to
get started.
XFINITY XR11
Remote Control
USER’S GUIDE
It’s simple to program your XFINITY Remote to control your
TV and Audio Video Receiver.
Your XFINITY Remote is already programmed to
control your set-top box. To program the remote
for control of Power, Volume, Mute and TV
Input on your TV or Power, Volume, and Mute
on your audio video receiver (AVR), including a
soundbar, follow the steps below.
Note: A soundbar is a type of AVR.
Here’s how to program your
remote for control of a TV or TV
and AVR:
1. Remove the battery pull tab from the remote
control battery compartment and make sure
your TV, AVR and set-top box are powered
on.
2. Refer to the “Setup Codes for TVs” and “Set-
up Codes for AVRs” sections on the back of
this guide to nd the manufacturers of your
TV and AVR.
3. Press and hold the Setup button on your
remote until the status LED changes from red
to green.
4. Enter the rst code listed for the TV manufac-
turer. The status LED should ash green
twice when the code is entered.
5. Press the TV Power button on the remote.
If the TV turns off, you have successfully
programmed your remote. Turn the TV back
on and press the VOL +/- and Mute buttons
to conrm they control the volume of your
device.
6. If the TV (or AVR) does not turn off or the
VOL +/- and Mute buttons do not work,
repeat the steps above using the next code
listed for your TV manufacturer.
CAN’T FIND YOUR CODE?
If you can’t program your remote for TV and/
or AVR control using the codes on the back of
this guide, follow the steps below to search for
your code.
1. Turn on your TV and AVR.
2. Press and hold the Setup button on your
remote until the status LED changes from red
to green.
3. To search for a TV code, enter 9-9-1 on the
remote. To search for an AVR code, enter
9-9-2. The status LED should ash green
twice.
4. Press the CH ^ button repeatedly to search
through the manufacturer codes until the
device you are programming turns off.
5. After the device turns off, press Setup. The
status LED on your remote should ash
green twice. Press the TV Power button on
the remote. If the device turns on, your have
successfully programmed your remote.
xfinity.com/remotes
Troubleshooting
GENERAL
TROUBLESHOOTING
:Q Why does the status LED ash red then
green while I am entering the code on my
remote?
:A You may have entered an incorrect code.
Check the code and try re-entering it.
:Q Why does the status LED ash red, but
there is no response when I press a key?
:A Make sure the remote is aimed at your TV
or AVR and is no farther than 15 feet away.
Also, make sure your set-top box is powered
on and in plain sight.
TV Power: Turns your TV on/off.
All Power: One button to turn the TV,
AVR and set-top box on/off.
Vol +/–: Turns the volume up and down
on the set-top box. After your remote is
programmed for TV and/or AVR control,
these keys control the TV or AVR’s
volume.
CH ^/∨: Selects the next higher or next
lower channel.
Mute: Turns the sound on and off.
Replay: Jumps back 15 seconds.
Note: Some features above require
programming the remote for control of a
TV and/or AVR.
Video Controls: Controls On Demand
or DVR viewing, Play/Pause, Fast-For-
ward, and Rewind.
Exit: Exits guide screens and returns you
to TV viewing.
Search: Search for content by channel,
program or key words.
Rec: Records content currently being
viewed.
XFINITY/Menu: Enters the XFINITY
menu for access to the guide, Saved
programs, On Demand and Apps.
Guide: Shortcut to TV listings.
OK: Selects the highlighted item within
the guide.
Last: When viewing content, enters the
Recent menu to select from the 9 most
recently viewed programs or, when in
the XFINITY menu, returns you to previ-
ous guide screen.
Info: Provides a program description.
A, B, C, D: Context-sensitive control
keys.
Keypad (0-9): Alphanumeric keys to
select content by channel number or
keywords.
Setup: Used for programming your
remote to control your TV, AVR, and
set-top box.
TV Input: Changes to the next available
input on your TV.
Note: Some features above require
programming your remote for control of
your TV.
Power: Enciende/apaga tu televisor.
All Power: Un sólo botón para encender/
apagar tu televisor y tu caja decodifica-
dora.
Vol +/–: Sube y baja el volumen de tu caja
decodicadora.
CH ^/∨: Selecciona el siguiente canal
hacia arriba o hacia abajo.
Mute: Enciende y apaga el sonido.
Replay:
Nota:
Video Controls: Controlan la visual-
ización de On Demand o DVR, Play
(reproducir)/Pause (pausa), Fast-For-
ward (avanzar rápidamente), y Rewind
(retroceder rápidamente).
Exit: Te saca de las pantallas de la guía y
te regresa a ver la televisión.
Search:
Rec: Graba el contenido que se está
viendo en ese momento.
Nota: Algunas funciones mencionadas
anteriormente requieren de una caja
decodicadora de DVR o acceso a la
programación On Demand.
XFINITY/Menu: Ingresa a los menús de
la guía en pantalla
Guide: Atajo a los listados de televisión.
OK: Selecciona el artículo resaltado
dentro de la guía.
Last: Te regresa al canal o a la pantalla de
la guía anterior.
Info: Proporciona la descripción de un
programa.
A, B, C, D: Teclas de control que fun-
cionan de acuerdo al contexto y que se
utilizan en conguraciones avanzadas.
Nota: Algunas de las funciones arriba
mencionadas requieren de una guía de
programación no disponible con todos los
aparatos.
Teclado numérico (0-9): Selecciona el
canal que deseas ver (ej., 0-9 ó 0-2-6).
Setup: Programa tu control remoto
para que funcione con tu televisor, caja
decodicadora o DTA.
TV Input:
Nota:
Here’s what your remote can do.
Esto es lo que tu control remoto puede hacer.
¡Disfruta de
XFINITY® TV
ahora mismo!
Programa tu control
remoto para comenzar.
XFINITY XR11
GUÍA DEL USUARIO
para el control remoto
xfinity.com/remotes
If you only want to program your remote for TV
control, you’re all set!
Continue with the following steps to program
your remote for AVR control.
Note: To program your remote for simultaneous
control of both a TV and AVR, the TV must be
programmed before the AVR.
7. Press and hold the Setup button on your
remote until the status LED changes from red
to green.
8. Enter the rst code listed for the AVR manu-
facturer. The status LED should ash green
twice when the code is entered.
9. Press the All Power button on the remote.
If the AVR turns off, you have successfully
programmed your remote. Turn the AVR back
on and press the VOL +/- and Mute buttons
to conrm they control the volume of your
device. If so, you’re all set!
10. If the AVR does not turn off or the VOL +/-
and Mute buttons do not work, repeat the
steps above using the next code listed for
your AVR manufacturer.
Here’s how to program your
remote for only AVR control:
1. Remove the battery pull tab from the remote
control battery compartment and make sure
your AVR and set-top box are powered on.
2. Find the manufacturer of your AVR on the
back of this guide.
3. Press and hold the Setup button on your
remote until the status LED changes from red
to green
Additional Feature: Aim Anywhere Control
See the back of this user guide to learn how
to pair your remote and set-top box* for Aim
Anywhere control, allowing you to control your
devices even when they are placed behind your
TV or in another room (up to 50 feet away).
*Aim Anywhere control is not supported by all
set-top boxes.
FCC Compliance Statement
This equipment has been tested and found
to comply with the limits for a Class B dig-
ital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful in-
terference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not used in
accordance with the instructions, may cause
harmful interference to radio communications.
There is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, the user is
encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving anten-
na.
• Increase or decrease the separation be-
tween the equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that which the re-
ceiver is connected.
• Consult the dealer or an experienced re-
mote control/TV technician for help.
• It is strongly recommended that the TV
be plugged into a separate wall outlet.
The user is cautioned that changes and mod-
ications made to the equipment without the
approval of the manufacturer could void the
user’s authority to operate this equipment.
This device complies with part 15 of the FCC
rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.
“CAUTION” : Exposure to Radio Frequen-
cy Radiation. Antenna shall be mounted in
such a manner to minimize the potential for
human contact during normal operation. The
antenna should not be contacted during op-
eration to avoid the possibility of exceed-
ing the FCC radio frequency exposure limit.
Helpful Tip: Additional remote control program-
ming support, including code lookup tool and
frequently asked questions, can be found at
xnity.com/remotes.
4. Enter the rst code listed for the AVR manu-
facturer. The status LED should ash green
twice when the code is entered.
5. Press the TV Power button on the remote.
If the AVR turns off, you have successfully
programmed your remote. Turn the AVR back
on and press the VOL +/- and Mute buttons
to conrm they control the volume of your
device. If so, you’re all set!
6. If the AVR does not turn off or the VOL +/-
and Mute buttons do not work, repeat the
steps above using next code listed for the
device manufacturer. You may need to try
several codes to nd the one that works for
your device.