TABLE OF CONTENTS IMPORTANT INFORMATION .................................................................................................................. 2 1. REGISTRATION ..................................................................................................................................... 3 2. UNDERSTANDING YOUR SAFE ...................................................................................................... 4 3. UNBOXING ...........................................................
DISCLAIMER - READ BEFORE SAFE SETUP PLEASE READ THIS INFORMATION CAREFULLY BEFORE OPERATING YOUR REMINGTON SAFE. DO NOT LOCK THIS MANUAL OR THE OVERRIDE KEYS IN YOUR SAFE. Thank you for choosing a Remington safe to protect your valuables. We are committed to securing, organizing and protecting your most important documents, valuables and keepsakes. Your safe is built to last a lifetime. However, please understand that the locking mechanism has precision parts.
1 . REGISTRATION Register your safe at www.remingtonsafes.com By registering your Remington safe we will be able to expedite and address any problems or challenges you may have which would otherwise require a notary letter and proof of payment. You can scan the QR Code to take you directly to the Remington registration page. REGISTRATION INFORMATION The information you record onto this page will be required in the event you cannot access the contents of your Remington safe.
2. UNDERSTANDING YOUR SAFE Override Key Entry (underneath key pad) Steel Reinforced Top Shelf Backlit UL Rated SecuRam™ Lock UL Rated Outlets with USB Ports Premium Quilted Door Organizer Barrel Rests Battery Location Premium Wheel Handle External Hinges Fully Wrapped Adjustable Shelves Bolt Down Hole Adjustable Shelf Rails Locking Bolts 3. UNBOXING WARNING: SAFES ARE HEAVY AND CAN BE UNSTABLE ON UNEVEN GROUND. PLEASE ENSURE EXTRA CAUTION WHEN DEALING WITH OR MOVING UNSECURED SAFES.
5. INITIAL ENTRY 1. Locate the quick start guide, override key, battery and STS opening tool inside the box on the front of the corrugate safe protective front cover. Step 1 Quick Start Set the provided override key aside in a safe place. NOTE: Do not store override keys inside your safe. Step 2 2. Locate the battery compartment at the bottom right side of the lock face.
5. INITIAL ENTRY (CONTINUED) 4. Take the STS opening tool from your “Getting Started Box” and place it around the hub as shown. 5. Enter the default USER CODE on the keypad. Default code is: 1-2-3-4-5-6 Step 4 Step 5 The light at the top of the keypad should light with each digit entered and flash 2X at completion indicating the code was entered correctly and the safe handle can be turned to open the safe. Clear NOTE: The Clear button can be used to clear numbers entered incorrectly. Step 6 6.
6. WHEEL HANDLE ASSEMBLY AND INSTALLATION 1. To assemble the wheel to the hub base, (if you haven’t already, please remove opening tool from the Hub) Step 1 Place the STS Wheel over the hub. Step 2 2. Locate and insert the 2 allen head screws provided through the holes in the wheel and into the hub base and tighten. Note: Do not overtighten. Step 3 3. Next, locate the R logo cover, on the back there will be a double sided tape, peel off the front side of the 2 sided tape to expose the tape.
7. USER CODE SET UP NOTE: It is beneficial read and understand all steps prior to beginning each section. WARNING: IT IS REQUIRED THAT THE USER CHANGE BOTH THE USER AND MANAGER CODES OF YOUR SAFE. FAILURE TO DO SO IS A POTENTIAL SECURITY RISK. 1. With your safe door still open, press “0” six times on your lock face, you will hear 1 beep and the light will flash 2 times. 2. Enter the existing default code 1-2-3-4-5-6, you will hear 1 beep and the light will flash 2 times. 3.
8. MANAGER CODE (CONTINUED) NOTE: It is beneficial read and understand all steps prior to beginning each section. WARNING: IT IS REQUIRED THAT THE USER CHANGE BOTH THE USER AND MANAGER CODES OF YOUR SAFE. FAILURE TO DO SO IS A POTENTIAL SECURITY RISK. CHANGING THE MANAGER CODE 1. With your safe door open, press “0” six times to enter Manager Code Edit Mode. You will hear 1 beep and the light will flash 2 times. 2. Enter your current Manager Code, or the default Manager Code (1-1-1-1-1-1).
8. MANAGER CODE (CONTINUED) CREATE A USER CODE WITH MANAGER CODE 1. Enter 6 digit MANAGER Code and HOLD DOWN LAST Digit, you will hear 1 beep and the light will flash 2 times. CONTINUE TO HOLD down until you hear 2 additional beeps. 2. Press "1", you will hear 1 beep and the light will flash 2 times. 3. Enter a new 6 digit code, you will hear 1 beep and the light will flash 1 time. 4. Re-Enter the new 6 digit code, you will hear 1 beep and the light will flash 1 time.
9. LOW BATTERY ALERT This lock face is equipped to alert you when the batteries are low. If you hear repeated beeping (8 beeps) when unlocking your safe, your battery is low and needs immediate replacement. Clear It is recommended you replace your battery annually. NOTE: Duracell or Energizer batteries are highly recommended 10. LOCKOUT MODE / TAMPER PROTECTION 1. After 4 consecutive rejected invalid code entries, your safe will enter lockout mode. 2. The keypad will be deactivated for 5 minutes.
11 . USING YOUR OVERRIDE KEY (CONTINUED) 3. To replace lock face, push exposed keypad cable back into safe as far as possible, then align guide holes in back of lock face with 2 metal screw heads on front of safe door. Step 3 Push the lockface in and down to secure the screw heads into the back of lock face guide holes. The lock face should now be in place. Clear 12. PROPER PLACEMENT AND MOVING OF SAFE WARNING: SAFES ARE VERY HEAVY AND AWKWARD TO HANDLE. PLEASE USE THE UTMOST CARE IN MOVING THE SAFE.
13. KEEPING YOUR SAFE DRY We recommend placing a moisture/protective barrier between your safe and concrete floor to prevent any moisture, mildew and rust damage to the safe. Installing your safe in a place with climate control (heat in the winter and cooling in the summer) is highly recommended. In areas of high humidity or frequent temperature fluctuations (garages) it is recommended to take appropriate precautions to ward against moisture damage.
. SECURING YOUR SAFE WARNING: YOUR SAFE IS DESIGNED TO SUPPORT ITSELF WHEN THE DOOR IS OPENED. HOWEVER, CAUTION SHOULD BE USED TO AVOID TIPPING. WHILE SECURING YOUR SAFE BE SURE TO HAVE A SECOND PERSON HOLD AND STABILIZE THE SAFE TO KEEP IT FROM TIPPING, CAUSING INJURY, AND/OR DAMAGE TO THE SAFE AND SURROUNDING STRUCTURES. FAILURE TO DO SO WILL COMPROMISE THE SAFETY, SECURITY, AND WARRANTY OF THE SAFE.
. INTERIOR LIGHTING This safe comes with proximity based interior lighting installed. When the USB powered internal lighting is plugged into the USB power source, the lighting will function automatically when the door is open. 17. LOCKED OUT OF YOUR SAFE In the event you have forgotten the security code your primary action will be to use your override keys in order to gain access to your safe and follow the Electronic Lock Security Setup Code instructions, starting at section 10.
LIFETIME WARRANTY SA Consumer Products, Inc. will repair or replace, at their sole discretion, any Remington gun safe damaged by fire, forced entry, forced attack or natural flood for the lifetime of the original owner. SA Consumer Products, Inc. will repair or replace, at their sole discretion, any Remington gun safe with defective parts, paint or lock for the lifetime of the original owner. If SA Consumer Products, Inc.