Preface Scope This manual is intended for use by qualified technicians familiar with similar types of communication equipment. It contains all service information and data required for the equipment. Caution The following precautions are recommended for personnel safety: DO NOT transmit until all RF connectors are verified secure and all connectors are properly terminated. SHUT OFF the power and DO NOT operate this equipment near electrical blasting caps or in a potential explosive atmosphere.
Brief Introduction 1 2 3 4 5 10 6 11 12 13 7 14 15 8 9 16 (1) ANTENNA (2) CHANNEL SELECTOR KNOB Used to select channel and squelch level. In addition, it can be programmed by the dealer to delete undesired channels from scan list or to select a CTCSS frequency. (3) LED INDICATOR Is red when transmitting Is green when receiving Flashes red when the battery voltage is low and approaching the cut-off point Flashes orange, when the radio receives proper DTMF or Two Tone decode signals.
(10)PTT BUTTON Used to switch between transmit and receive mode. (11)LAMP BUTTON Used to turn on/off the LCD backlight. Press the [LAMP] button, the backlight will illuminate for about 5 seconds and then automatically turn off. Press any key other than [LAMP] button, the timer will retime. If you press the [LAMP] button, the backlight will light off. (12)MONI BUTTON Used to monitor the selected channels.
(9) Appears when keypad lock is on.
Radio Modes 1. Frame of Radio Modes Select the function you want from the modes and make the necessary settings.
2.
MODE USER MODE Conventional Mode Key POWER ON While holding down [LAMP] and Function Set Mode [○] key simultaneously, turn on the power (in 2 seconds) DEALER MODE Turn on the power to enter Conventional Mode ●] key to enter Function Set Mode. Press [ ○] key to enter DTMF Set Mode. DTMF Set Mode As above Press [ Channel Set Mode As above Press [ New function set mode Wired Clone Mode Wireless Clone Mode As above ■] key to enter Channel Set Mode. Press [□] key to enter New Function Set Mode.
5. Press [●] key to return to Dealer Mode from current option, and the current data shown on the display will not be stored. 6. Press [PTT] to store current function setting and a beep will sound to confirm the action. 7. END appears when settings in function mode are completed. Function No.
13 TIME OUT TIMER OFF 30s~300s 60s (30s/1STEP) TOT OFF TOT 30 TOT 300 14 TOT ALERT TIME OFF 1 ~ 60 (10s/1STEP) TOTA OFF TOT off. TOTA 1 When this feature is enabled, the radio will call an TOTA 60 15 16 TOT REKEY TIME TOT RESET TIME OFF 1s ~ 60s OFF (1s/1STEP) OFF 1s ~15s OFF (1s/1STEP) When OFF, in order to protect power amplifier, max. time of continuous transmission is set as 10 minutes. Maxi. time of continuous transmission alert at the set time.
2. In dealer mode, press [○] key to enter DTMF Set Mode. 3. Use Channel Selector knob and the 16 keys (0~9, *, #, A~D) to set DTMF function ON/OFF or select the setting. 4. Press [PTT] to store the selected settings, except functions 31 and 32, which are stored with the 16 keys, and the menu goes to next function option. 5. Press [○] key to return to Dealer Mode. The current setting displayed on LCD will not be stored. 6. Press [PTT] to store function settings and a Beep sounds to confirm the action. 7.
33 34 it) 12keys (0 ~ 9,*,#) DTMFK 12 Disable [A] [B] [C][D] keys. 16keys (0 ~ 9,*,#,A ~ D) Disable DTMFK 16 Enable DHT ON OFF STSD OFF Enable [A] [B] [C][D] keys. Function that continues Do not transmission for two seconds Hold even if manual DIAL key is Hold released. Prohibit Store & Send function. ON STSD ON Permit Store & Send function. D Code DKEYA D Send the code for D. 1s ~ 16s (1s/1STEP) DKEYA 1 DKEYA 16 Make unmodulated transmission for preset time.
In self-programming set, when the basic function is OFF, corresponding settings in the below table can be set, but not valid. Function name Settings Disable conditions 2-TONE/ DTMF DTMF 37.DTMF signaling is OFF 2.[SCN] TO 7.Priority is fixed or selected. 6.Priority Fixed, Selected 2.[SCN] is OFF 7.Priority CH 6.Priority is OFF or fixed. 8.Look Back A 6.Priority is OFF 9.Look Back B 6.Priority is OFF 10.Revert CH Priority, Priority + Selected 6.Priority is OFF 11.Dwell Time 2.
Function No. 45 46 47 48 49 50 14 Function Name Settings (Defaults are underlined) Group NO GROUP TONE Tone Type A TONE Group Tone Duration Channel Label Size KEY1 KEY2 KEY3 Display Remarks GRPT OFF 2-tone group tone off. GRPT A Set 2-tone group tone as tone A. B TONE GRPT B Set 2-tone group tone as tone B. 0.5~10s 0.5s step: 0.1s GTDUR 0.5 Group tone time.
51 KEY4 Key Lock Variable QT SQL No Function SCAN DIAL TA LO Display Label Display Frequency Display Mode Scan ADD/DEL Key Lock Variable QT SQL K3 KLOCK K3 VQT K3 SQL K4 OFF K4 SCAN K4 DIAL K4 TARE K4 LO K4 DCHAR K4 DFREQ K4 DMODE K4 SADD K4 KLOCK K4 VQT K4 SQL <- Default Self-programming (channel setting) 1. Turn on the power while pressing [LAMP] and [○] key, radio enters the dealer mode in 2 seconds. 2. In dealer mode, press [■] key, radio enters Channel Set Mode. 3.
RX CTCSS SIGNALING OFF OFF Code selection → Channel Selector knob ●] key CTCSS (standard) 67.0Hz ~ 250.3Hz QT 67.0 CTCSS changes in 0.1 Hz step increment → [ QT 250.3 CDCSS changes in 1 step increment,→ [ CTCSS (not standard) (0.1Hz step) 67.0Hz ~ 250.3 Hz QT 67.0* Toggle signaling between CDCSS and –CDCSS→[ QT 250.3* Toggle among blank, CTCSS frequency and CDCSS (standard) DQT023N ●] key ○]. □ CDCSS→[ ] key “TX FREQUENCY” follows this setting.
Wideband/Narrowband ID CODE (DTMF) Wide Narrow WIDE NARROW ID Display about one seconds when entering this setting. 000 9999999999 -------0 ID is input, enter number→[10 digit keys(0-9)] 9999999999 If more than 8, scroll it TTS_R 1 Code selection→Channel selector knob Return to “Channel Select” function when 99 channels are not all set. When 99 channels are all set, END is displayed. Display about one seconds when entering this setting.
Appendix 2: CTCSS Frequency No. Frequency [Hz] No. Frequency [Hz] No. Frequency [Hz] No. Frequency [Hz] 1 67.0 11 94.8 21 131.8 31 186.2 2 69.3 12 97.4 22 136.5 32 192.8 3 71.9 13 100.0 23 141.3 33 203.5 4 74.4 14 103.5 24 146.2 34 210.7 5 77.0 15 107.2 25 151.4 35 218.1 6 79.7 16 110.9 26 156.7 36 225.7 7 82.5 17 114.8 27 162.2 37 233.6 8 85.4 18 118.8 28 167.9 38 241.8 9 88.5 19 123.0 29 173.8 39 250.3 10 91.5 20 127.
2. Transmit the clone data by pressing [MONI], red LED glows during data transfer. When data transfer is completed, “END” is displayed on LCD, and the red LED turns off. 3. When “End” is displayed, press [MONI] button to continue to clone another radio or press [LAMP] to return to Dealer Mode. [MONI] Sending clone data Red LED on clone data transfer end Red LED off [LAMP] Dealer Mode Target radio Operation 1. Turn On the power.
[ MONI ] Dealer Mode Clone Mode 2. Turn Channel Selector knob to select the frequency used for the wireless clone. [Channel Selector] Dealer Mode Clone Mode 3. Start the first half (00-50%) data transmission by pressing [PTT]. “00 CLONE” is displayed on LCD and red LED glows. The leftmost digits (00) on LCD show data transfer rate, and as data transmission proceeds, the digits count upwards in increments of 1. Transmit power is set as LOW POWER. [PTT] Clone Mode 4.
7. When the second half data transfer is completed, the LED turns off and “END” is displayed. Press [MONI], radio returns to Clone Mode and you can clone another radio or press [MONI] to return to Dealer Mode. Clone Mode Clone Mode Target Side Operation 1. Turn POWER ON while pressing [LAMP] and [○] key, in about 2 seconds radio enters the Dealer Mode. Then press [MONI] to enter Wireless Clone Mode. The frequency displayed on LCD is the initial frequency matching the destination. 2.
(1) Attach the antenna to the source radio. (2) Remove the antenna from the target radio. (3) Keep radios as close as possible. Note: During cloning do not execute any action that might interrupt the cloning such as shutting off power. TEST MODE Menu Mode 1. Turn the power ON while pressing [LAMP] and [■] key, in about 2 seconds the radio enters Test Mode and LCD displays “TEST”. After two seconds, the first setting option “ADJUST” is displayed on LCD.
3. Connect the source radio and the target radio with an interface cable. 4. Turn the target radio on. 5. Now press [□] key to enter Adjustment Data Clone Mode. LCD displays “–C–“. 6. Press [MONI] key to transmit the adjustment data. 7. Red LED glows during data transfer. When data transfer is completed, “END” is displayed on LCD and red LED turns off. 8. When “End” is displayed, press [MONI] to continue to clone another radio. 9. Press [■] key to exit from Adjustment Data Clone Mode.
1. Once the destination is set, previous channel settings (frequencies, CTCSS and channel functions) will be deleted and some functions are also changed. Therefore, do not make destination set except when EEPROM is replaced or other unavoidable conditions happened. 2. Destination of RPV599APlus is set as 8, frequency is 148~174MHz. And destination of RPU499APlus is 11, frequency 450-470MHz. Frequency Test Mode (for frequencies checking and radios repairing) Operation 1.
2.5KHz 6.25KHz 5KHz 12.5KHz Notes: 1. The frequency display range is between 100MHz and 550MHz. When PLL is unlocked, “beeps” sound. The frequency should not be out of corresponding frequency spectrum. 2. Step increment is not displayed on LCD. CTCSS Operation 1. In Frequency Test Mode, hold down [LAMP] and then press [○] key, the radio enters CTCSS set mode. Turn Channel Selector knob to change the CTCSS frequency. 2.
CTCSS N CDCSS N SQL CEN SQL LOW SQL HIGH 5. Press [□] key to adjust the Transmit High Power, Transmit Low Power, Battery Reference Value, CTCSS Deviation (Wideband), CDCSS Deviation (Wideband), CTCSS Deviation (Narrowband), CDCSS Deviation (Narrowband), BUSY Reference Value (Center Frequency), BUSY Reference Value (Low Frequency) and BUSY Reference Value (High Frequency) individually. 6. Press [■] key to exit from the Adjustment Mode and return to the menu of Test Mode. LCD displays “ADJUST”.
that the red LED flashes. The point where the red LED is flashing indicates detection of the low voltage. 5. Press [□] key to store the alignment value into the memory and return to the “CTCSS W” display. Press [■] key to cancel the alignment value and return to the “BATT REF” display. Adjusting CTCSS Deviation (Wideband) Use this procedure to adjust the transmit CTCSS deviation (Wideband). 1. Connect the modulation analyzer to the radio. 2. Turn Channel Selector knob to select the setting option “CTCSS W”.
Adjusting CDCSS Deviation (Narrowband) Use this procedure to adjust the transmit CDCSS deviation (Narrowband). 1. Connect the modulation analyzer to the radio. 2. Turn Channel Selector knob to select the setting option “CDCSS N”. 3. Transmission is performed automatically at Low Power and the preset CDCSS is sent when the [PTT] key is pressed. After the frequency display for one second, the display “CDCN XXX” now appears (XXX=1 to 255). If the CDCSS is set OFF, then 023 is sent. 4.
into the memory and continue to the alignment of squelch 3, and now “SQL3 XXX” displays. (XXX=1 to 255) 8. Then output a signal from the signal generator at which you want squelch 3 to open. Adjust by using the Channel Selector knob just same as with squelch 9. 9. Press [□] key to store the alignment value into the memory and return to the “SQL HIGH” display. Press [■] key to cancel the alignment value and return to the “SQL LOW” display.
12 13 14 15 480 490 360 380 √ √ √ √ √ √ √ √ √ √ √ √ √ 45.05 46.35 46.35 45.05 1 1 1 1 480 490 360 380 470 480 350 370 490 500 370 390 Note: About busy channel lockout *1: Transmission is prohibited if a signal appears with incompatible CTCSS/CDCSS; *2: Transmission is prohibited if a signal appears with incompatible CTCSS/CDCSS or DTMF/2-Tone. ALL RESET MODE Operation 1. Turn POWER ON while pressing [LAMP] and [○] key, in about 2 seconds, the radio enters the Dealer Mode. 2.