Operating Instructions for the Serie S Sub-Bass Systems REL Acoustics Limited North Road, Bridgend Industrial Estate Bridgend, CF31 3TP United Kingdom Telephone: +44 (0)1 656 768 777 Fax: +44 (0) 1 656 766 093 Web: www.rel.
IMPORTANT SAFETY INSTRUCTIONS [major heading] 1 Read all of these instructions. 2 3 4 5 6 7 8 Save these instructions for future use. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with automotive polish and micro fiber cloth. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
The mains plus is used as disconnect device. The mains plug of the apparatus should not be obstructed OR should be easily accessed during intended use. To be completely disconnected from the power input, the mains plug of the apparatus shall me disconnected from the mains. An appliance with a protective earth terminal should be connected to a mains outlet with a protective earth connection. Les conduites Plus est utilisé comme dispositif de déconnexion .
9 Ne pas contourner le dispositif de sécurité de la prise de terre . Une fiche de terre a deux lames et une troisième broche de mise à la terre . La troisième broche est fournie pour votre sécurité . Si la fiche fournie ne rentre pas dans votre prise , consultez un électricien pour le remplacement de la prise obsolète . 10 Protégez le cordon d'alimentation ne soit piétiné ou pincé, en particulier au niveau des fiches , des prises de courant , et le point de sortie de l'appareil.
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital Device, pursuant to Part 15 of the FCC Rules.
Wireless Freedom with Zero Compression: Longbow™ Once our team achieved the high standards for performance our customers expect of all REL subwoofers, we turned our attention to connectivity methods. In addition to our comprehensive array of hard-wired inputs, Serie S benefits from the finest sounding, most natural wireless system available at this time. In order to achieve high quality wireless, the REL team found a new chipset remarkable for its speed and lack of delay.
instantly transform to a powerhouse with LFE when watching movies. This feature requires no switching, but instead is a seamless benefit to doing things the REL way. This feature provides real benefit if you wish to play music in stereo mode in the purist audiophile way and also in REL Theatre Reference mode with no switching necessary. By connecting BOTH High Level and .1 concurrently and setting your processor to “Large” or “Full Range”, the best possible performance will be obtained.
PAGE BREAK 1 Volume Control for HI/LOW Level input: Use to adjust output when using either HI Level or LOW Level input. Do not use both simultaneously. 2 Volume Control for .1/LFE Input: Use to adjust output level when using .1/LFE input from a 5.1 amplifier or processor. 3 Crossover: Used to select crossover frequency. Variable between 30Hz and 120Hz. 4 Low-Level Left channel Phono Input: Used to connect low-level to the output of a preamplifier, integrated amplifier or receiver. (For home cinema, use .
To remove the Neutrik® Speakon® plug, grip body of plug, place thumb on chrome lever, move lever backwards, rotate plug anticlockwise quarter turn and withdraw. The high-level input is designed to accept the stereo (two-channel) signals from the speaker terminals of your receiver, integrated amplifier or basic amplifier.
amplifier. The easy and foolproof connection at the REL is done with a Neutrik® Speakon® connector. The purpose of connecting to the speaker output terminals is one of the unique secrets of REL’s success. By connecting to the High Level input on the REL from the amplifier, you build forward the sonic signature of your main system, including the tonal balance and timing cues of the entire electronics chain. In this way, the REL is fed the exact signal that is fed to the main speakers.
• If connecting a REL as a dedicated rear channel sub, connect the black wire of the REL to either the left rear or right rear negative speaker terminal; connect the yellow wire to the left rear positive speaker terminal; connect the red wire to the right rear positive speaker terminal. If the amplifier is of balanced differential design, please follow the instructions in the section above labeled Differential Connection.
5 Orientation: Once the position from the corner has been established, the orientation of the woofer must be determined by rotating the REL from an imagined centre point at the rear of the REL. As the REL is moved from one side to the other listen for the greatest level of output and bass linearity. In effect, the REL should be left in the position where it is playing the loudest and lowest.
PAGE BREAK Technical The Serie S models use an unusual method of bass loading. They are designed to operate below normal system resonance. This has been achieved without the normal form of bass boost or electronic equalization.
Power Saving Efficiency: All REL sub bass system designs utilize a true On-Off switch that affords the owner the ability to turn off their unit completely, without having to unplug the A/C mains cord. When a REL sub bass system is switched off using the On-Off switch on the rear panel it draws ZERO power.
During initial setup, use the REL this way. If you are using a REL Longbow™ transmitter for initial setup, the wireless switch must be enabled, please follow instructions for pairing included in the REL Longbow™ transmitter manual.
After initial setup, if you wish to employ the standby mode, simply move the power mode switch into the up position to “STANDBY”. Model Power Draw at Standby S/2 S/3 S/5 > 0.5 Watts > 0.5 Watts > 0.
PAGE BREAK S/5 Specifications [major heading] Type: Front-firing active woofer, down-firing passive radiator Active Drive Unit: 12 in., 300mm long-throw, die cast Aluminium chassis Passive Radiator: 12 in.
REL Longbow Wireless capability: Yes- REL Longbow™ transmitter [required]. Sold separately. Protection System Fully Electronic with SET-SAFE: Yes D.C. Fault: Yes Output Short: Yes Mains Input Voltage: 220-240 volts, 110-120 volts for certain markets Fuses: 5 Amp semi delay 220 volts operation 9 Amp semi delay 120 volts operation Dimensions W x H x D, Including Feet and Rear Panel Controls: 16 x 16.7 x 18.25 in., (406 x 424 x 463.5 mm) Add 1.75in (44.
Supplied Accessories Mains Lead: Yes Neutrik Speakon Interconnect 10 Metres Nominal: Yes Users Manual: Yes In the interest of product development, REL Acoustics Limited reserve the right to vary these specifications without notice 19